Fast-Cutting Carbide Square End Mills for Stainless Steel and Titanium
Variable spacing between the flutes reduces vibration, allowing these end mills to provide fast cuts, smooth finishes, and long tool life. They have a high helix angle and a wear-resistant coating for excellent shearing and chip removal in stainless steel and titanium. Made of solid carbide, they are harder, stronger, and more wear resistant than high-speed steel and cobalt steel end mills for the longest life and best finish on hard material. Their extreme hardness means they are brittle, so a highly rigid setup, such as a CNC machine, is necessary to prevent the end mill from breaking. End mills have a square end for milling square slots, pockets, and edges. All are center cutting, allowing plunge cuts into a surface.
Aluminum-titanium-nitride (AlTiN) coated end mills get additional wear and temperature resistance from their finish.
For technical drawings and 3-D models, click on a part number.
| Mill Dia. | Shank Dia. | Lg. of Cut | Overall Lg. | Flute Spacing | Helix Angle | For Use On | End Mill Type | Each | |
Aluminum Titanium Nitride (AlTiN) Coated | |||||||||
|---|---|---|---|---|---|---|---|---|---|
4 Flute | |||||||||
| 11mm | 12mm | 26mm | 83mm | Variable | 36°-38° | Stainless Steel, Titanium | Center Cutting | 00000000 | 0000000 |
High-Speed Steel Square End Mills
Use these end mills for general purpose milling in most material, such as aluminum, brass, bronze, iron, and steel. They have a square end for milling square slots, pockets, and edges.
End mills with fewer flutes provide better chip clearance for high-volume, high-speed plunge, slotting, and roughing cuts; end mills with more flutes provide a finer finish and operate with less vibration when run at high speeds.
Use uncoated end mills for general purpose milling and short production runs. Use titanium-nitride (TiN) coated end mills for demanding, high-speed jobs in hard material as well as for longer production runs. They’re more wear resistant than uncoated end mills, which means they last longer when run at similar speeds.
Center-cutting end mills allow plunge cuts into a surface.
For technical drawings and 3-D models, click on a part number.
| Mill Dia. | Shank Dia. | Lg. of Cut | O'all Lg. | Flute Spacing | Helix Angle | For Use On | End Mill Type | Each | |
Uncoated | |||||||||
|---|---|---|---|---|---|---|---|---|---|
2 Flute | |||||||||
| 11mm | 9.5mm | 20.6mm | 64mm | Equal | 30° | Aluminum, Brass, Bronze, Iron, Plastic, Stainless Steel, Steel | Center Cutting | 00000000 | 000000 |
4 Flute | |||||||||
| 11mm | 9.5mm | 25.4mm | 68mm | Equal | 30° | Aluminum, Brass, Bronze, Iron, Plastic, Stainless Steel, Steel | Center Cutting | 0000000 | 00000 |
Titanium Nitride (TiN) Coated | |||||||||
2 Flute | |||||||||
| 11mm | 9.5mm | 20.6mm | 64mm | Equal | 30° | Aluminum, Brass, Bronze, Hardened Steel, Iron, Nickel, Stainless Steel, Steel, Tool Steel | Center Cutting | 0000000 | 00000 |
Roughing High-Speed Steel Square End Mills
Serrations along the cutting edge act as chip breakers, so these end mills can remove large amounts of material at high speeds. They are high-speed steel for general purpose milling in most material, such as aluminum, brass, bronze, iron, and steel. Their square end makes them good for milling square slots and edges.
End mills with fewer flutes provide better chip clearance for high-volume, high-speed plunge, slotting, and roughing cuts; end mills with more flutes provide a finer finish and operate with less vibration when run at high speeds.
Center-cutting end mills allow plunge cuts into a surface.
For technical drawings and 3-D models, click on a part number.
| Mill Dia. | Shank Dia. | Lg. of Cut | O'all Lg. | Flute Pitch | Flute Spacing | Helix Angle | For Use On | End Mill Type | Each | |
Uncoated | ||||||||||
|---|---|---|---|---|---|---|---|---|---|---|
4 Flute | ||||||||||
| 11mm | 12mm | 22mm | 79mm | Fine | Equal | 30° | Aluminum, Brass, Bronze, Iron, Plastic, Stainless Steel, Steel | Center Cutting | 00000000 | 000000 |
Cobalt Steel Square End Mills with Two Milling Ends
When one end wears out, switch to the opposite end for two times the life of a standard cobalt steel end mill. With better heat and wear resistance than high-speed steel, these cobalt steel end mills can run at higher speeds and provide better performance on hard material, such as iron, hardened steel, titanium, and tool steel. Their square ends make them good for milling square slots, pockets, and edges. All are center cutting, allowing plunge cuts into a surface.
End mills with four flutes provide a finer finish and operate with less vibration when run at high speeds.
For technical drawings and 3-D models, click on a part number.
| Mill Dia. | Shank Dia. | Lg. of Cut | O'all Lg. | Flute Spacing | Helix Angle | For Use On | End Mill Type | Each | |
Uncoated | |||||||||
|---|---|---|---|---|---|---|---|---|---|
4 Flute | |||||||||
| 11mm | 12.7mm | 25.4mm | 105mm | Equal | 30° | Aluminum, Brass, Bronze, Hardened Steel, Iron, Nickel, Plastic, Stainless Steel, Steel, Titanium, Tool Steel | Center Cutting | 0000000 | 000000 |