System of Measurement System of Measurement |
|---|
|
Mill Diameter Mill Diameter | Show |
|---|
|
Mill Diameter Mill Diameter | Hide |
|---|
For Use On For Use On |
|---|
|
|
For T-Slot Bolt Size For T-Slot Bolt Size |
|---|
|
Material Material |
|---|
|
Neck Length Neck Length |
|---|
|
Mill Thickness Mill Thickness |
|---|
|
DFARS (Defense Acquisition Regulations Supplement) DFARS (Defense AcquisitionRegulations Supplement) |
|---|
Individual/Set Individual/Set |
|---|
 | Individual |
Number of Milling Ends Number of Milling Ends |
|---|
 | 1 |
Shank Type Shank Type |
|---|
 | Round |
Finish Finish |
|---|
|
Neck Diameter Neck Diameter |
|---|
|
Number of Flutes Number of Flutes |
|---|
 | 2 |
End Mill Type End Mill Type |
|---|
|
Flute Spacing Flute Spacing |
|---|
|
Flute Type Flute Type |
|---|
|
Helix Angle Helix Angle |
|---|
|
High-Speed Steel Square End Mills
Use these end mills for general purpose milling in most material, such as aluminum, brass, bronze, iron, and steel. They have a square end for milling square slots, pockets, and edges.
End mills with fewer flutes provide better chip clearance for high-volume, high-speed plunge, slotting, and roughing cuts; end mills with more flutes provide a finer finish and operate with less vibration when run at high speeds.
Use uncoated end mills for general purpose milling and short production runs. Use titanium-nitride (TiN) coated end mills for demanding, high-speed jobs in hard material as well as for longer production runs. They’re more wear resistant than uncoated end mills, which means they last longer when run at similar speeds.
Center-cutting end mills allow plunge cuts into a surface.
| Mill Dia. | Shank Dia. | Lg. of Cut | O'all Lg. | Flute Spacing | Helix Angle | For Use On | End Mill Type | Each | |
Uncoated | |||||||||
|---|---|---|---|---|---|---|---|---|---|
2 Flute | |||||||||
| 31/32" | 1" | 1 5/8" | 4 1/8" | Equal | 30° | Aluminum, Brass, Bronze, Iron, Plastic, Stainless Steel, Steel | Center Cutting | 0000000 | 000000 |
Titanium Nitride (TiN) Coated | |||||||||
2 Flute | |||||||||
| 31/32" | 1" | 1 5/8" | 4 1/8" | Equal | 30° | Aluminum, Brass, Bronze, Hardened Steel, Iron, Nickel, Stainless Steel, Steel, Tool Steel | Center Cutting | 00000000 | 00000 |
High-Speed Steel T-Slot End Mills
Use these end mills for general purpose work in most material, such as aluminum, brass, bronze, iron, and steel. They're often used to create slots in machine tool tables, indexing tables, and other workholding surfaces.
Mill | Neck | ||||||||
|---|---|---|---|---|---|---|---|---|---|
| For T-Slot Bolt Size | Dia. | Thick. | Shank Dia. | Dia. | Lg. | Overall Lg. | For Use On | Each | |
Uncoated | |||||||||
| 1/2" | 31/32" | 25/64" | 3/4" | 0.531" | 63/64" | 3 7/16" | Aluminum, Brass, Bronze, Hardened Steel, Iron, Plastic, Stainless Steel, Steel, Titanium, Tool Steel | 0000000 | 000000 |
Carbide-Tipped T-Slot End Mills
Made of carbide-tipped steel, these end mills maintain a sharper, harder edge at high temperatures than high-speed steel. Use them to create slots in machine tool tables, indexing tables, and other workholding surfaces.
Mill | Neck | |||||||||
|---|---|---|---|---|---|---|---|---|---|---|
| For T-Slot Bolt Size | Dia. | Thick. | Shank Dia. | Dia. | Lg. | Lg. of Cut | Overall Lg. | For Use On | Each | |
Uncoated Carbide-Tipped High-Speed Steel | ||||||||||
| 1/2" | 31/32" | 25/64" | 3/4" | 0.531" | 63/64" | 25/64" | 3 7/16" | Brass, Bronze, Hardened Steel, Iron, Nickel, Stainless Steel, Steel, Titanium, Tool Steel | 0000000 | 0000000 |
V-Belts
