An interlocking steel frame in these mounts prevents collapse, even if the rubber fails.

Connect these mounts to your air supply for vibration and shock isolation in compression load applications.

The polyurethane base on these mounts resists solvents, gasoline, and oil, while the metal plate sustains heavy loads.

Made of nitrile rubber, these mounts are oil resistant for use in compression load applications with punch presses, milling machines, grinders, and air compressors.

These mounts withstand exposure to weather and resist oil, antifreeze, and other petroleum-based fluids.

Made of tightly layered stainless steel mesh, these mounts withstand temperatures up to 500° F.

An interlocking steel frame in these mounts prevents collapse, even if the rubber fails.

Designed for tight spaces such as inside machinery, these mounts fit into a cutout, so they so they have a low top profile.

Specifically designed for light vertical loads, these mounts buckle to protect lightweight equipment such as small fans and pumps from vibration.

In addition to having a wider temperature range than our other vibration-damping bushings, these have excellent weather resistance.

Ribbed bushings are more flexible than our smooth vibration-damping bushings, so they're easier to install.

Press these grommets into a hole to add cushion on both sides.

In addition to having a wider temperature range than our other ribbed vibration-damping grommets, these have excellent weather resistance.

In addition to having a wider temperature range than our other vibration-damping washers, these have excellent weather resistance.

Made of 303/304 stainless steel, these mounts resist corrosion from water and most chemicals.

An economical choice for applications in corrosive environments that don't require high load capacities, these mounts have a plastic base.

Yellow zinc-plated steel is more corrosion resistant than nickel-plated steel.

Black-oxide steel has a dull shine for areas where appearance is a concern.

Made entirely of 316 stainless steel, these metric mounts have superior corrosion resistance.

Punch-out holes in the base let you bolt down these metric mounts to keep your equipment stationary.

Well-suited to damp environments, these mounts have a stainless steel stud and nut for corrosion resistance.

Well-suited to damp environments, these mounts have a stainless steel stud and nut for corrosion resistance.

Made entirely of 316 stainless steel, these mounts are our most resistant to corrosion from chemicals, solvents, and water.

Nickel-plated steel has some corrosion resistance.

Well-suited to damp environments, these mounts have a stainless steel nut for excellent corrosion resistance.

Made of 303 stainless steel, these mounts resist corrosion from water and most chemicals.

Often used on wobbly tables, these mounts automatically adjust up to 5/16" to compensate for uneven floors.

Made of 303 stainless steel, these metric mounts resist corrosion from water and most chemicals.

Protect surfaces from scratches and wear.

Use these mounts on heavy machines and equipment.

Able to withstand temperatures up to 350° F, these have the highest maximum temperature of our plastic mounts.

A hex nut at the base of the stud allows for easy height adjustment.

Able to shoulder up to 1,500 psi per mounting point, nitrile pads can support heavy machinery.

These soft pads work well for isolating vibration with light loads such as lab and testing equipment.

Reinforced with fabric so extreme compression won’t deform them, these pads protect surfaces from impact, dampen vibration and noise, and act as stable connection points. They’re commonly known as bearing pads.

Made of fiber-reinforced PVC, these pads endure exposure to corrosive chemicals, such as cleaning solvents, chlorine, and hydrochloric acid.

Higher deflection ratings translate to greater vibration and shock isolation than our other vibration-damping leveling mounts.

A two-piece design simplifies installation and requires less clearance than one-piece mounts.

A two-piece design requires less clearance than one-piece mounts and simplifies installation—raise your machine just enough to slide the base underneath, then insert the stud from above.

Bolt these mounts down to keep your equipment stationary.

Excellent chemical resistance makes these PTFE plastic feet the best choice for harsh environments.

All of these bumpers are reinforced with an embedded washer or base plate for strength. Often used as feet, spacers, and vibration dampers, they absorb shock to prevent damage to equipment and surfaces. They're also good for starting and stopping motion on automated machines. Install them with screws.

These bumpers are at a 90° angle to protect corners on equipment, walls, and docks from damage caused by carts, vehicles, and other moving objects. Install them with screws.

Mount these bumpers on a threaded stud. All are reinforced with a steel core or base plate for strength. Often used as feet, spacers, and vibration dampers, they absorb shock to prevent damage to equipment and surfaces. They're also good for starting and stopping motion on automated machines.

These bumpers withstand temperatures up to 300° F, which is at least twice as high as our other load rated bumpers. Use them in applications that require specific load capacities. All are reinforced with a base plate for strength. Often used as feet, spacers, and vibration dampers, these bumpers absorb shock to prevent damage to equipment and surfaces. They're also good for starting and stopping motion on automated machines and conveyors. Mount them on a threaded stud.

These bumpers withstand temperatures up to 300° F, which is twice as high as our other load rated bumpers. Use them in applications that require specific load capacities. All are reinforced with a base plate for strength. Often used as feet, spacers, and vibration dampers, these bumpers absorb shock to prevent damage to equipment and surfaces. They're also good for starting and stopping motion on automated machines and conveyors. Twist them into a threaded hole.

Twist these bumpers into a threaded hole. Often used as feet, spacers, and vibration dampers, they absorb shock to prevent damage to equipment and surfaces.

Push the stem into a hole for quick installation. These bumpers are commonly used as feet on instruments and bench-top equipment to keep them from sliding. They're also good as spacers between sheets of material. Also known as stem and grommet bumpers.

Press these bumpers into place with the adhesive backing. Use them as feet and spacers on instruments and small appliances to limit sliding, vibration, and noise. They're comparable to Bumpon bumpers.

Make bumpers the size and shape you need. Use them as feet and spacers on instruments and small appliances to limit sliding, vibration, and noise. Press them into place with the adhesive backing.

A magnetic base makes it easy to attach, move, and replace these bumpers on metal surfaces. Use them for guarding, aligning, and positioning parts.

For quick and easy installation, wrap these bumpers around tubing, rods, machinery legs, control shafts, and levers to protect them from impact, dents, and scratches. They're also good for providing protection during shipment and storage.