For Use On For Use On | Show |
---|
|
For Use On For Use On | Hide |
---|
For Joining For Joining |
---|
Maximum Temperature Maximum Temperature |
---|
|
Minimum Temperature Minimum Temperature |
---|
|
Type Type |
---|
|
Formulation Formulation |
---|
|
Adhesive Type Adhesive Type |
---|
|
Cure Type Cure Type |
---|
|
Consistency Consistency |
---|
|
Shear Strength Shear Strength |
---|
|
Approximate Coverage Approximate Coverage |
---|
|
Mixing Required Mixing Required |
---|
|
Peel Strength Peel Strength |
---|
|
Connection Type Connection Type |
---|
|
More
With excellent resistance to corrosive chemicals and salt water, these epoxies work in tough conditions. Epoxies are the strongest structural adhesives. Choose an adhesive that hardens quickly for fast repairs, or one that hardens slowly to allow more time for positioning.
The size listed is the combined total of the two parts. Use cartridges with a dispensing gun and mixer nozzle to simultaneously mix and dispense adhesives.
Container | Strength | ||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Size | Type | Begins to Harden | Reaches Full Strength | Shear, lbs./sq. in. | Peel, lbs./in. wd. | Mix Ratio | Consistency (Viscosity) | Temp. Range, °F | Color | Environment | For Joining | Each | |
Adhesives | |||||||||||||
1.69 oz. | Cartridge | 30 min. | 24 hrs. | 360 | Not Rated | 2:1 | Thick Liquid (7,000 cP) | -50° to 350° | Amber | Corrosive, Salt Spray, Submersible | Metal, Metal to Plastic, Metal to Rubber, Metal to Composites, Plastic, Plastic to Rubber, Plastic to Composites, Rubber, Rubber to Composites, Composites | 000000 | 000000 |
1.69 oz. | Cartridge | 40 min. | 24 hrs. | Not Rated | Not Rated | 2:1 | Thick Liquid (10,000 cP) | -65° to 350° | White | Corrosive, Salt Spray, Submersible | Metal, Metal to Plastic, Plastic | 000000 | 00000 |
Fasten hard-to-bond plastics, such as polypropylene and polyethylene, with these adhesives. They bond dissimilar materials. Epoxies are the strongest and most weather- and chemical-resistant structural adhesives. Choose an adhesive that hardens quickly for fast repairs, or one that hardens slowly to allow more time for positioning.
The size listed is the combined total of the two parts. Use cartridges with a dispensing gun and mixer nozzle to simultaneously mix and dispense adhesives.
Container | Strength | ||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Size, oz. | Type | Begins to Harden | Reaches Full Strength | Shear, lbs./sq. in. | Peel | Mix Ratio | Consistency (Viscosity) | Temp. Range, °F | Color | For Joining | Includes | Each | |
1.69 | Cartridge | 30 min. | 24 hrs. | 360 | Not Rated | 2:1 | Thick Liquid (9,000 cP) | -50° to 350° | Amber | Metal, Metal to Plastic, Metal to Rubber, Metal to Composites, Metal to Glass, Plastic, Plastic to Rubber, Plastic to Composites, Plastic to Glass, Rubber, Rubber to Composites, Rubber to Glass, Ceramic, Composites, Glass, Wood, Wood to Glass | __ | 000000 | 000000 |
1.69 | Cartridge | 30 min. | 24 hrs. | 360 | Not Rated | 2:1 | Thick Liquid (9,500 cP) | -50° to 350° | Amber | Plastic | 1:1 and 2:1 Mix Ratio Plungers, Mixer Nozzle, One 2-oz. Bottle of Etching Solution | 0000000 | 000000 |
1.69 | Cartridge | 30 min. | 24 hrs. | 360 | Not Rated | 2:1 | Thick Liquid (9,500 cP) | -50° to 350° | Amber | Plastic | 1:1 and 2:1 Mix Ratio Plungers, Mixer Nozzle, Mixing Stick, Two 4-oz. Bottles of Etching Solution, Two Brushes, Two Mixing Trays | 0000000 | 000000 |
1.69 | Cartridge | 90 min. | 72 hrs. | Not Rated | Not Rated | 1:1 | Thick Liquid (6,000 cP) | -85° to 270° | Amber | Metal, Metal to Plastic, Metal to Rubber, Metal to Glass, Plastic, Plastic to Rubber, Plastic to Glass, Rubber, Rubber to Glass, Ceramic, Composites, Glass, Wood, Wood to Glass | __ | 000000 | 00000 |
48 | Bottle | 30 min. | 24 hrs. | 360 | Not Rated | 2:1 | Thick Liquid (9,000 cP) | -50° to 350° | Amber | Metal, Metal to Plastic, Metal to Rubber, Metal to Composites, Metal to Glass, Plastic, Plastic to Rubber, Plastic to Composites, Plastic to Glass, Rubber, Rubber to Composites, Rubber to Glass, Ceramic, Composites, Glass, Wood, Wood to Glass | __ | 000000 | 000000 |
Also known as sloshing compounds, these two-part epoxies bond to rough and rusty surfaces in fuel tanks to repair leaks and prevent further corrosion. They withstand permanent immersion in fuel, oil, and harsh solvents. Use them with metal, plastic, and fiberglass tanks. Mix the smaller can with the bigger one and pour into your fuel tank. Rotate the tank to coat the interior and dump out any excess. Allow to cure overnight. Size listed is the combined total of the two parts.
1.5-pint container can treat a 10-gallon fuel tank. 3-pint container can treat a 20-gallon fuel tank.
Container | ||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|
Size, pt. | Type | Begins to Harden, min. | Reaches Full Strength, hrs. | Consistency | Mix Ratio | For Use Outdoors | Temp. Range, °F | Color | Finishing Method | For Use On | Each | |
1.5 | Can | 5 | 24 | Thick Liquid | 2:1 | No | 70° to 90° | Amber | Drill, Sand, Tap | Aluminum, Brass, Bronze, Copper, Silver, Steel, Stainless Steel, Cast Iron, Galvanized Iron, Galvanized Steel, Titanium, Acrylic Plastic, Polycarbonate Plastic, ABS Plastic, PVC Plastic, CPVC Plastic, PETG Plastic, PVDF Plastic, Polyimide Plastic, Nylon Plastic, Polyethylene Plastic, Polypropylene Plastic, Vinyl Plastic, Fiberglass, Ceramic, Porcelain | 0000000 | 000000 |
3 | Can | 5 | 24 | Thick Liquid | 2:1 | No | 70° to 90° | Amber | Drill, Sand, Tap | Aluminum, Brass, Bronze, Copper, Silver, Steel, Stainless Steel, Cast Iron, Galvanized Iron, Galvanized Steel, Titanium, Acrylic Plastic, Polycarbonate Plastic, ABS Plastic, PVC Plastic, CPVC Plastic, PETG Plastic, PVDF Plastic, Polyimide Plastic, Nylon Plastic, Polyethylene Plastic, Polypropylene Plastic, Vinyl Plastic, Fiberglass, Ceramic, Porcelain | 0000000 | 00000 |
Use these two-part fillers to rebuild cracked or worn plastic surfaces. The size listed is the combined total of the two parts.
Surface fillers in a cartridge come with a mixer nozzle, but require a gun (sold separately) for dispensing. For best results, use a primer (sold separately).
Container | ||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|
Size | Type | Begins to Harden | Reaches Full Strength | Consistency | Mix Ratio | Approx. Coverage @ Thick. | Temp. Range, °F | Color | Finishing Method | For Use On | Each | |
Surface Fillers | ||||||||||||
1.7 oz. | Cartridge | 5 min. | 30 min. | Thick Liquid | 1:1 | 11 sq. in. @ 1/4" | -20° to 180° | Gray | Sand | Polystyrene Plastic, Polycarbonate Plastic, Polyurethane Rubber, ABS Plastic, PVC Plastic, CPVC Plastic, PETG Plastic, PVDF Plastic, Polyimide Plastic, Polyethylene Plastic, Polypropylene Plastic | 0000000 | 000000 |