The insulation resists water, oil, and chemicals, so these cords withstand dirty and greasy environments.

Use these cords where ignitable gas and dust may be present. They're CSA certified for Class I, Division 1 and 2, Groups B, C, and D; and Class II, Division 1 and 2, Groups F and G hazardous environments.

Run these cords through high-traffic areas that are dirty and greasy. They have a thick insulation that resists water, oil, and chemicals, and protects against abrasion.

Power multiple devices with one extension cord.

Thick insulation protects the internal wires of these cords, so they can be used in high-traffic areas and over rough surfaces.

These self-coiling cords return to their retracted length after stretching for tangle-free storage.

Also known as hospital-grade cords, these have extra-tight connections to prevent them from detaching. The connectors are marked with a green dot.

These cords have an oil- and water-resistant insulation and impact-resistant connectors for protection in harsh environments.

Keep personnel safe from electric shock with these cords.

Cover mated connectors on extension cords to prevent disconnection.

Hardwire one of these converters to an extension cord to keep personnel safe from electric shock.

Attach these splitters to an extension cord to power multiple devices from one cord.

Separately control each device plugged into these strips—each outlet has its own power switch.

The power switch to these outlet strips is on a 44" long cord, so you can control power even when the strips are in hard to reach places, such as under a desk.

A combination of an outlet box, cord, and duct, these outlet strips minimize tripping hazards and protect the cord from damage.

Also known as hospital-grade outlet strips, these outlets have an extra-tight fit to prevent plugs from detaching. They are marked with a green dot.

Install these extra-long strips onto the frame of an electrical cabinet.

Create a permanent outlet system without opening walls. These outlet strips mount to a wall with clips and hardwire to an existing electrical system.

These curved outlet strips clamp onto a pole or table leg.

Mount these strips into standard 19" wide electronics racks and enclosures.

Use these unshielded cords where signal interference is not a concern.

The M12 threaded connectors on these cords are more vibration resistant than RJ45 connectors.

Send data between computers, printers, servers, and switches with these cords—they have an M12 plug on one end and an RJ45 plug on the other.

Connect computers, monitors, printers, and other devices with DB connections.

Display video from one source on two different monitors.

Transfer data between computers, printers, and mobile devices.

Pinch the sides on the plugs of these cords to insert them; they lock into a socket to prevent the cord from detaching.

Rated IP67, these cords withstand washdowns and temporary submersion. Connect them to a USB device inside an enclosure.

Transmit audio, video, and data signals over long distances with minimal signal loss.

Often used in assembly line networks and Fieldbus connections, these cords have B-coded M12 connections.

Often used to connect multiple monitors to a single computer, these cords send video and audio to a display device.

Replace the cords connecting your robot controller and teach pendant when they become worn, or switch them out for a different length.

These self-coiling cords stretch to full length and then return to their retracted length for tangle-free storage.

After a power failure, these cords must be manually reset, preventing unexpected equipment startup.

All cords have a country-specific plug to power equipment from international outlets.

Also known as hospital-grade cords, these cords have an extra-tight connection to prevent them from detaching. The plug is marked with a green dot.

Create a vibration-resistant connection—the socket on these cords locks onto any male receptacle and will not detach until manually unlocked.

Create a vibration-resistant connection—the socket on these cords securely locks onto any male receptacle and will not detach until manually unlocked.

These cords work with any Milwaukee tool with a pin socket (Quik-Lok) connection.

Plug these cords into computers, lab equipment, and office machines that have IEC connections.

Controlled winding prevents the cord from whipping at the end, making winding safer and extending the life of the cord and reel.

Intended for demanding applications, these reels include an oil- and water-resistant extension cord.

Made of impact-resistant plastic, these reels are more durable than other automatic-wind cord reels.

A steel stand makes these reels more rugged than light duty cord reels.

Plug a cord into these reels.

Store and transport cords.

Change a turn-lock to a straight-blade connection, or a straight-blade to a turn-lock connection.

Also known as plenum cable, this cable has low-smoke insulation and can be used without conduit in ductwork and above a drop ceiling. Use it to send data between computers, servers, and switches.

Also known as plenum cable, this cable has low-smoke insulation and can be used without conduit in ductwork and above a drop ceiling. It has an oil-resistant insulation to protect wires as the cable moves from duct to equipment or machinery.

Use this cable for complex and high-speed data and signal transmission.

Connect devices such as sensors, programmable logic controllers, and actuators to an automated network.

Often used to send signal and data to order pickers and cranes, this cable withstands continuous motion applications without degrading data or signal transmission.

Use these connectors and cords to make Ethernet connections in washdown environments.

Protect your hose when it’s not in use.