The insulation on these cords resists water, so they can be used outdoors.

Run these cords through high-traffic areas that are dirty and greasy. They have a thick insulation that resists water, oil, and chemicals, and protects against abrasion.

Thick insulation protects the internal wires of these cords, so they can be used in high-traffic areas and over rough surfaces.

Power multiple devices with one extension cord.

Insulated to resist water, oil, and solvents, these cords withstand dirty and greasy environments.

In addition to an outlet on the end, these cords have multiple inline outlets.

These self-coiling cords return to their retracted length after stretching for tangle-free storage.

Also known as hospital-grade cords, these have extra-tight connections to prevent them from detaching. The connectors are marked with a green dot.

Attach these splitters to an extension cord to power multiple devices from one cord.

Also known as hospital-grade cords, these cords have an extra-tight connection to prevent them from detaching. The plug is marked with a green dot.

All cords have a country-specific plug to power equipment from international outlets.

Use these cords with computers, lab equipment, and office machines that have IEC connections.

All cords have a country-specific plug on one end and an IEC socket on the other end.

The shielding blocks signal interference from nearby equipment and devices.

Power multiple devices from one power source.

These cords work with any Milwaukee tool with a pin socket (Quik-Lok) connection.

Use these cords with hydraulic and air-powered valves, motors, pumps, and pressure switches. They have a solenoid valve socket on one end and an M12 threaded plug on the other.

Save energy by automatically turning off unused outlets. The master outlet controls five outlets and shuts off power to the other outlets when a device plugged into the master is turned off.

The power switch to these outlet strips is on a 44" long cord, so you can control power even when the strips are in hard to reach places, such as under a desk.

An isolated ground connection on these outlets protects computers and other sensitive equipment from external signals that interfere with the equipment’s performance.

A combination of an outlet box, cord, and duct, these outlet strips minimize tripping hazards and protect the cord from damage.

Connect multiple devices from a single outlet.

These curved outlet strips clamp onto a pole or table leg.

Create a permanent outlet system without opening walls. These outlet strips mount to a wall with clips and hardwire to an existing electrical system.

Install these extra-long strips onto the frame of an electrical cabinet.

Power up mobile devices and other electronics.

Change a turn-lock to a straight-blade connection, or a straight-blade to a turn-lock connection.

Minimize the risk of electric shock by adding ground fault protection to a standard outlet.

Cover unused electrical outlets or plug prongs to protect them from dust, dirt, liquids, and other contaminants.

Use these connectors in general purpose residential and commercial applications.

Eliminate the need for wire stripping; snap-on terminals pierce the wire insulation and grip the wire securely. Access the wire connection by opening the hinged housing.

Visually confirm that connectors have power; they have an indicating light that is visible from any angle.

Protect computers and other sensitive equipment from electromagnetic interference (EMI). Also known as isolated ground receptacles.

Visually confirm that sockets have power—the face lights up when they're connected. The rubber housing protects them from damage caused by drops and other impact.

When mated, connectors meet NEMA 6P, NEMA 12, and either IP67 or IP69K.

Also known as hospital-grade connectors, these have an extra-tight fit when mated to remain secure in high-vibration environments.

Add a fuse to protect equipment from current overload. When mated with a receptacle, these plugs have an extra-tight fit to remain secure in high vibration environments. They're also known as hospital grade plugs.

Use connectors where ignitable gas and dust may be present. They are UL listed for Class I, Division 1 and 2, Groups C and D; Class II, Division 1 and 2, Groups F and G; and Class III hazardous environments.

Pair these connectors with standard IEC power cords to bring power into or out of your electronic devices.

Connect one end to a fixture and the other to a ballast. These connectors allow you to safely disconnect a failed ballast without exposing you to live wires.

Energize Milwaukee tool batteries with these chargers.

Keep Bosch tool batteries powered with these chargers.

Restore power to batteries for Dremel tools.

Charge up to eight batteries at once.

After the battery is fully charged, these chargers continuously provide a low-level charge to maintain the battery without overcharging.