A few turns is all it takes to join these cords, which have thick threads similar to a light bulb, for a secure connection in washdown and high-vibration areas. They detach just as fast for frequent maintenance. IP68 rated when mated, these cords block out dust and water if briefly submersed. They carry higher currents than mini cords, so they’re often used to power cameras, machine tools, HVAC equipment, and I/O modules, yet they’re compact to save space. Their housing resists UV rays for outdoor use. All have cables that are known as TC-ER, meaning they meet crush and impact requirements for exposed cable in cable carriers.

Connect these cords to mating quick-connect connectors.

Add caps to keep out dust and debris when these cords aren’t connected.

For technical drawings and 3-D models, click on a part number.

The M12 threaded ends on these cords seal out contaminants and resist coming loose from vibration better than the RJ45 ends on traditional Ethernet cords. Use them in tough, rugged environments to send high-speed data between sensors, switches, servers, computers, and PLCs not protected by control panels. These cords can power devices as they send data, as long as devices are Power over Ethernet (PoE) compatible. They are often used within Ethernet/IP, Profinet, and EtherCat systems. Their poles and keyways adhere to standard coding layouts, reducing the chance you’ll mismatch connections.

All cords are backward compatible, so they work in networks that meet the same or lower ethernet cable category. For example, a Category 6 cord will work in a Category 5 network, but it will only run at the Category 5 speed.

A- and X-coded cords send data faster than D-coded cords, so they’re good for robotics and multi-step programs.

With either TPE or polyurethane insulation, all cords stand up to harsh factory conditions, chemicals, and UV rays. All are also highly flexible, so they’re good for jobs with continuous motion, such as robotics. TPE-insulated cords resist abrasion and won’t pit or crack from welding runoff.

Use unshielded cords where signal interference is not a concern. Double-shielded cords have layers of braid and foil that block signal interference from nearby devices, preventing impact to transmission speeds and data.

90° elbow cords sit flush against equipment, so they fit behind machinery in areas where space is tight.

When mated, all cords are IP67 rated to protect against dust and temporary submersion. IP65-rated cords stand up to washdowns. IP66K-rated cords stand up to high-pressure washdowns.

Add caps to protect cords and maintain their IP ratings when not in use.

For technical drawings and 3-D models, click on a part number.

To send high-speed data in tough, rugged environments, these cords have an M12 connector on one end that threads onto switches, sensors, and other devices prone to vibration. The other end has a traditional RJ45 plug that connects to Ethernet equipment, such as computers, IO modules, and programmable logic controllers (PLCs). These cords can also power devices as they send data, so you don’t need a separate power cord. But, the device must be Power over Ethernet (PoE) compatible. They’re often used with EtherNet/IP, Profinet, and EtherCAT systems. With TPE insulation, they stand up to bending in robotics applications. It also means they resist abrasion and won’t pit or crack from chemicals, sunlight, and welding runoff.

Thanks to its threads and IP rating, the M12 end is water and dust tight when mated. Poles and keyways on its face adhere to standard coding layouts, which reduces the chance of mismatching connections.

When choosing an Ethernet cord, make sure you match or exceed your network’s ethernet cable category. These cords are backward compatible—for example, a Category 6 cord will work in a Category 5 network, but it’ll only run at the Category 5 speed.

A- and X-coded cords send data faster than D-coded cords, so they’re best for systems that run multi-step programs, such as robotics.

Use unshielded cords where signal interference is not a concern. Double-shielded cords have layers of braid and foil that block signal interference from nearby devices, maintaining their speed and data integrity.

Cords with a 90° elbow run along the side of equipment, so they fit behind machines and in tight spaces.

Add caps to protect connectors and maintain their IP rating when not in use.

For technical drawings and 3-D models, click on a part number.

These cords contain a single pair of twisted wires, making them lighter and more flexible than other Ethernet cords. They’re good for transportation, robotics, and automation applications. Cords have a metal locking tab to create a more secure connection than cords with RJ45 connectors, and are easier to install than coaxial cords and cords with M12 connectors. They transmit power as well as data, making them useful in places without an easily accessible power supply. These cords are shielded to block out signal interference from nearby devices.

Cords meet IEEE standards for data transmission speeds and protocols. All meet EN 60811-404 for resistance to mineral oil. They’re compliant with IEC 60332-1-2 for flame retardancy and IEC 63171-6 for single pair Ethernet cord dimensions and compatibility.

For technical drawings and 3-D models, click on a part number.

Often used in assembly line networks and Fieldbus connections, these cords have B-coded M12 connections. The ends are threaded to withstand the vibration and shaking of an automated assembly line. Shielded with both braid and foil, these cords block interference from nearby devices, maintaining their signal integrity. PVC insulation protects these cords and resists abrasion, though it contains halogen. When mated or capped, these cords are IP67 rated, so they withstand dust and temporary submersion.

The socket end has an extra hole on the face that is not wired.

Add caps to protect connectors and maintain their IP ratings when not in use.