Mount this light on a pole to illuminate pedestrian areas such as streets and walkways.

Also known as wall packs, these lights mount to exterior walls and ceilings.

These lights are UL listed for use in hazardous locations where flammable/combustible gases, vapors, and liquids may be present.

No need for wiring—these lights plug-in with a three-prong plug.

Powered by the sun, these security lights function in areas that don’t have access to electricity. They’re often used to shine light on parking lots, landscaping, signs, entryways, and other outdoor spaces.

Mount these lights flush with ceilings in wet locations—all are sealed to keep out humidity and dripping, splashing, and falling liquids. Unlike recessed can lights, which require a separate housing, these fit directly into a cutout in your ceiling and are held in place by springs.

Also known as jelly jar lights. These fixtures have a guard that protects the lens from breaking.

Suspend or mount with fasteners to the ceiling.

A sealed lens keeps moisture out to protect these lights against washdowns.

Also known as pigtail holders. Temporarily wire these sockets to provide light during construction.

These LED lights have an air-tight seal to protect against contaminants.

Attach to your key ring or hat so you’ll always have a flashlight on hand. They're rated for use in environments where hazardous material is present.

Rated for use in environments where hazardous material is present.

Small enough to fit in your pocket.

All of these flashlights stand up to wet environments.

Made of stainless steel, these pocket-size flashlights have a smooth, easy-to-clean surface.

Because these flashlights are buoyant, they're easy to recover when dropped in the water.

Safe for use in environments where hazardous material is present.

These IP67 rated lights withstand temporary submersion in a maximum of one meter of water for up to 30 minutes. They're compact for easy transport to job sites with no electrical power.

Rated IP65, these lights are sealed to protect against light washdowns from a garden hose. They have a height-adjustable stand and light heads that pivot up and down to direct light where it's needed.

A series of bulb heads are attached to a power cord to provide overhead lighting for job sites.

Use these with portable lights that use screw-in bulbs.

With a NEMA 4X rating, these lights resist degradation when exposed to corrosive liquids, withstand liquids sprayed during washdowns, and are dust tight.

These lights are sealed to protect against humidity, moisture, and dripping and splashing liquids.

These lights are UL rated for use in hazardous locations where flammable/combustible gases, vapors, and liquids may be present.

These lights swing out from the wall to illuminate loading docks and trailers.

Just like traditional tubular lights that illuminate your machine with a bright white light, these lights can also be programmed to switch over to a red or green light for communicating machine status.

Mount these lights into a recessed opening on your machine—they sit flush against the surface for a streamlined appearance.

Similar in function to tubular machine lights, except strip machine lights have a flat lens that directs light downward.

These lights cast a narrower beam than other gooseneck-arm machine lights. Reposition them faster and more easily than articulating-arm lights.

The articulating arm on these lights holds its position better than gooseneck-arm lights, especially around vibration.

Bulbs have two filaments, which operate at different brightness levels.

Offset pins on the base lock these bulbs into sockets. One pin is slightly higher on the base than the other pin.

Commonly used in signs, instruments, indicators, and flashlights.

Use these bulbs in tight spaces, such as in indicators and vehicle lights.

These miniature bulbs are sized to fit older telephone switchboards, signs, instruments, and indicators.

A sealing gasket keeps out oil and other contaminants.

Install miniature light bulbs into control panels, machines, and other devices using bulb holders.

These bulbs are small, but very bright, so they're often used in flashlights and optical instruments such as projectors and microscopes.

Switch from the yellow light of high-pressure sodium to the white light of metal halide without changing ballasts.

Illuminate parking lots and roads with the warm, yellow light of these high-pressure sodium bulbs.

These slender bulbs are used in lamps and task lights.

Small but powerful, these bulbs are commonly used in stage and security lighting.

Use these bulbs in ovens and equipment that reaches temperatures up to 500° F.

Pins on the base lock these bulbs into sockets to withstand vibration.

Use these bulbs in standard sockets, panels, and appliances.

Often used in task lights, these two-pin wedge base bulbs are comparable to PL, Dulux, and Biax bulbs.

Replace bayonet base incandescent bulbs in exit signs with longer-lasting, energy-efficient LEDs.

Also known as beacon lights and signal lamps, these bulbs provide high-intensity light so they're often used in security warning devices and machinery.

Insert removers into broken bulbs and twist to take the bulbs out. A built-in tray collects the glass shards.

Replace hard-to-grip miniature bulbs in equipment such as control panels and indicators. Install new bulbs without leaving behind oil from your fingers that can cause bulbs to burn out.

A solid lens retains glass if a screw-in bulb breaks.