Inlet Diameter Inlet Diameter |
|---|
|
Power Power |
|---|
|
Airflow Airflow |
|---|
|
Housing Material Housing Material |
|---|
|
Electrical Phase Electrical Phase |
|---|
|
Voltage Voltage |
|---|
|
Wheel Diameter Wheel Diameter |
|---|
|
Overall Height Overall Height | Show |
|---|
|
Overall Height Overall Height | Hide |
|---|
Outlet Shape Outlet Shape |
|---|
|
Power Source Power Source |
|---|
|
DFARS (Defense Acquisition Regulations Supplement) DFARS (Defense AcquisitionRegulations Supplement) |
|---|
Mounting Hole Diameter Mounting Hole Diameter |
|---|
|
Number of Speeds Number of Speeds |
|---|
|
Outlet Height Outlet Height |
|---|
|
Outlet Width Outlet Width |
|---|
|
Wheel Material Wheel Material |
|---|
|
Drive Type Drive Type |
|---|
|
Electrical Connection Type Electrical Connection Type |
|---|
|
Minimum Temperature Minimum Temperature |
|---|
|
Motor Speed Motor Speed |
|---|
|
Volume Volume |
|---|
|
Chemical-Resistant Blowers
For resistance to chemicals as well as corrosion, these blowers have a plastic housing. They install in ductwork similar to duct fans, but are for use where high static pressures are present. Use them for equipment cooling, material conveying, drying, ventilating, and exhausting. All blowers have a totally enclosed motor enclosure, which can be used in dirty, dusty, and damp environments.
Note: Airflow depends on the resistance created by ductwork. This resistance, known as static pressure (SP), is measured in inches of water.
PVC plastic housing offers greater chemical resistance than the fiberglass housing. It resists strong oxidizing acids such as sulfuric acid but will not withstand contact with perchloric acid.
For technical drawings and 3-D models, click on a part number.
Blowers | |||||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Outlet | Overall | Mounting | Replacement Wheels | ||||||||||||||
| Airflow @ Static Pressure | Motor Speed, rpm | Power, hp | Ht. | Wd. | Inlet Dia. | Wheel Dia. | Ht. | Wd. | Dp. | Wt., lbs. | Housing Material | Fasteners Included | Hole Dia. | Each | Each | ||
208-230/460V AC, Three Phase—Hardwire | |||||||||||||||||
| 4,700 cfm @ 1 in. of H₂O 4,900 cfm @ 1/2 in. of H₂O | 1,725 | 5 | 11 7/8" | 9 3/4" | 13" | 14 1/2" | 31 1/2" | 30" | 29 3/4" | 172 | PVC Plastic | No | 3/8" | 0000000 | 000000000 | 0000000 | 000000000 |
Hazardous Location Chemical-Resistant Blowers
These blowers have an explosion-proof motor that is UL listed and CSA certified for Class I, Divisions 1 and 2, Group D; and Class II, Divisions 1 and 2, Groups F and G hazardous locations. For resistance to chemicals as well as corrosion, they have a plastic housing. They install in ductwork similar to duct fans, but are for use where high static pressures are present. Use them for equipment cooling, material conveying, drying, ventilating, and exhausting. All blowers have a totally enclosed motor enclosure, which can be used in dirty, dusty, and damp environments.
Note: Airflow depends on the resistance created by ductwork. This resistance, known as static pressure (SP), is measured in inches of water.
PVC plastic housing offers greater chemical resistance than the fiberglass housing. It resists strong oxidizing acids such as sulfuric acid but will not withstand contact with perchloric acid.
For technical drawings and 3-D models, click on a part number.
Blowers | ||||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Outlet | Overall | Mounting | Replacement Wheels | |||||||||||||
| Airflow @ Static Pressure | Motor Speed, rpm | Power, hp | Ht. | Wd. | Inlet Dia. | Wheel Dia. | Ht. | Wd. | Dp. | Housing Material | Fasteners Included | Hole Dia. | Each | Each | ||
230/460V AC, Three Phase—Hardwire | ||||||||||||||||
| 4,700 cfm @ 1 in. of H₂O 4,900 cfm @ 1/2 in. of H₂O | 1,725 | 5 | 11 7/8" | 9 3/4" | 13" | 14 1/2" | 31 1/2" | 30" | 29 3/4" | PVC Plastic | No | 3/8" | 0000000 | 000000000 | 0000000 | 000000000 |