Use these general purpose 18-8 stainless steel screws for a variety of fastening applications. They have good chemical resistance.

More corrosion resistant than 18-8 stainless steel screws, these button head screws have excellent resistance to chemicals and salt water. They may be mildly magnetic.

18-8 stainless steel pan head screws have good chemical resistance and may be mildly magnetic.

These steel pan head screws are coated for corrosion resistance.

Stainless steel screws have excellent corrosion resistance in most environments.

18-8 stainless steel pan head screws have good chemical resistance and may be mildly magnetic.

These screws have good chemical resistance.

These screws have good chemical resistance.

Stainless steel screws have excellent corrosion resistance in most environments.

Made from stainless steel, these screws are chemical resistant and may be mildly magnetic.

Made from alloy steel, these screws are nearly twice as strong as stainless steel button head screws.

The washer on these screws has sharp external teeth that dig into surfaces for maximum holding power and vibration resistance. Also known as Sems screws, the washer rotates freely but is permanently attached.

Use these general purpose 18-8 stainless steel screws for a variety of fastening applications. They have good chemical resistance.

More corrosion resistant than 18-8 stainless steel screws, these screws have excellent resistance to chemicals and salt water. They may be mildly magnetic.

These screws have good chemical resistance and may be mildly magnetic.

These steel screws have a zinc plating for mild corrosion resistance.

These 18-8 stainless steel screws have good chemical resistance and may be mildly magnetic.

Brass screws are electrically conductive, nonmagnetic, and have good corrosion resistance.

With a tamper-resistant Torx or Torx Plus drive (also known as a pin-in Torx or Torx Plus drive), these screws are difficult to remove without special tools.

These 18-8 stainless steel screws have a hardened steel drill point to penetrate steel and are coated to increase corrosion resistance.

These steel screws are available with corrosion resistant finishes. A rubber-bonded washer compresses to form a watertight seal. They save you time and effort by drilling their own holes and fastening in a single operation.

Made from 410 stainless steel, these screws are strong, wear resistant, and mildly chemical resistant.

These steel screws cut threads in drilled holes as they’re turned, so they require less driving torque and cause less stress on your material than thread forming screws.

These steel screws are zinc plated to resist corrosion in wet environments.

Commonly used with door hinge hardware, these screws cut threads in material such as aluminum and brass.

These screws speed installation by drilling, tapping, and fastening wood and metal in a single operation.

Brass binding barrels and screws are corrosion resistant in wet environments and electrically conductive.

These nuts have good chemical resistance and may be mildly magnetic.

Made from nylon 6/6, these nuts resist oil, grease, and solvents (except mineral acids).

One-third the weight of steel, these aluminum nuts are corrosion resistant in wet environments and nonmagnetic.

These nuts tighten when turned to the left; once fastened, they resist loosening from counterclockwise motion.

These locknuts have good chemical resistance.

These locknuts are about half the height of standard nylon-insert locknuts. Use them in light duty low clearance applications or jam one against a hex nut to hold it in place.

Also known as Keps and K Lock nuts, these locknuts have a free-spinning tooth lock washer that grips the material surface instead of threads for easy installation and mild vibration resistance.

Made from 18-8 stainless steel, these flange locknuts have good chemical resistance and may be mildly magnetic

Brass coupling nuts are corrosion resistant in wet environments and electrically conductive.

These cap nuts have excellent resistance to chemicals and salt water.

These thumb nuts have good chemical resistance and may be mildly magnetic.

These thumb nuts are corrosion resistant in wet environments, electrically conductive, and nonmagnetic. The flange distributes pressure over a large area to reduce stress on your part.

Wings provide more leverage for greater torque while tightening than knurled-head thumb nuts.

These nuts have good chemical resistance and may be mildly magnetic.

About twice as strong as aluminum rivet nuts, these low-profile rivet nuts have a cadmium or tin-zinc plating for corrosion resistance.

18-8 stainless steel threaded rods have good chemical resistance.

One-third the weight of steel, aluminum threaded rods resist corrosion in wet environments.

A distorted thread grips the screw to resist loosening.

Assortments include various sizes of helical inserts and a tap, a drill bit, and an installation tool for each thread size.