6-32 Fasteners | McMaster-Carr

Filter by

System of Measurement

Thread Size

Length

Material

Stainless Steel

Drive Style

Drilled Spanner

External Square

Tamper-Resistant Hex

Tamper-Resistant Torx

Tamper-Resistant Torx Plus

Fastener Head Type

Finish

Black Zinc Plated

Cadmium Yellow-Chromate Plated

Corrosion-Resistant Coated

Dry Film Lubricated

Neoprene Coated

Phosphate Coated

Threading

Partially Threaded

Threaded on Both Ends

Threaded on One End

Head Diameter

Rounded Head Style

Socket Head Profile

Head Height

Specifications Met

Federal Specification

Thread Type

Flat Head Profile

Drive Size

Thread Direction

Right Hand and Left Hand

Countersink Angle

Thread Spacing

Screw Size

DFARS Specialty Metals

Thread Fit

Metric Class 6g

Metric Class 6H

Unified Standard Class 1A

Unified Standard Class 1B

Unified Standard Class 2A

Unified Standard Class 2B

Unified Standard Class 3A

Unified Standard Class 3B

Tensile Strength

Less than 10,000 psi

10,000 psi to 19,999 psi

20,000 psi to 29,999 psi

30,000 psi to 99,999 psi

100,000 psi or greater

RoHS

Compliant with Exemptions

Export Control Classification Number (ECCN)

REACH

How can we improve?

4,277 Products

Fastening and Joining

Socket Head Screws

Socket Head Screws

With a deeper drive than flat and rounded head screws, these withstand more torque for a tighter hold

Rounded Head Screws

Rounded Head Screws

Sit just above the surface for a low-profile finish and hold tighter than flat head screws

Flat Head Screws

Flat Head Screws

Fit in countersunk holes for a flush finish that won't snag on surrounding parts

Hex Head Screws

Hex Head Screws

Used with nuts to create a stronger joint than flat and rounded screws

Tighten and loosen by hand without the need for tools

Captive Panel Screws

Captive Panel Screws

Secure panels and enclosures while still having access to them

Set Screws

Exert pressure at the tip to hold parts in place, unlike screws that hold material together with threads

Hanger Bolts

Suspend pipe and other fixtures with wire or cable ties

Shoulder Screws

Shoulder Screws

Rotate parts around the cylinder under the head to guide and align them during installation

Tapping Screws

Fasten a range of materials together without needing to tap the hole first

Studs

Press, weld, or screw in place to add a threaded fastening point

Oval Head Screws

Oval Head Screws

The domed top sits slightly above the surface of countersunk holes for a decorative look

Hex Nuts

Handle most general fastening needs

Locknuts

Hold fasteners in place to prevent loosening from vibration

Easy to tighten and loosen by hand for making frequent adjustments

Cap Nuts

Cover and protect threads while adding a finished look; also known as acorn nuts

Flange Nuts

The flange distributes pressure, so you don't need a washer

Coupling Nuts

Connect and extend threaded rods

Socket Nuts

Install in recessed holes and tight spots where a wrench won’t fit; also known as Allen nuts

Square Nuts

Flat sides won’t spin in channels and square holes

Sealing Nuts

Prevent leaks and block out contaminants with a rubber seal

Rivet Nuts

Add threads to thin panels with access from only one side; also known as blind inserts

Threaded Inserts

Threaded Inserts

Create new threads or repair stripped threads

Press-Fit Nuts

Push into drilled or punched holes to add threads to thin panels

Screw-Mount Nuts

Screw-Mount Nuts

Mount with screws, rivets, and nails to add threads to a surface

Push Nuts

Press onto threads for a light duty hold that’s faster to install than typical nuts

Rivet-Mount Nuts

Rivet-Mount Nuts

Add threads in hard-to-reach areas and materials that are too thin to be tapped

Clip-On Nuts

Slide onto the edge of thin panels to create a fastening point

Weld Nuts

Weld to metal surfaces to add permanent threads

Snap-In Nuts

Push into square holes in thin materials to add bolts for aligning off-center parts

Adhesive-Mount Nuts

Adhesive-Mount Nuts

Attach threads to material that’s too thin for a threaded insert

Standoff Caps

Create a finished look on standoffs and protect them from dirt and debris

Standoffs

Threaded to separate or connect parts as well as position components in assemblies

Binding Barrels and Screws

Binding Barrels and Screws

Thread together for a low-profile fastener

Quick-Release Pin Receptacles

Quick-Release Pin Receptacles

Secure quick-release pins when you don’t have a through hole

Single-End Studs

Single-End Studs

Use the unthreaded end as a pivot point, hinge, shaft, or locator pin

Anchors

Secure anything from signs to heavy machinery in concrete, brick, and drywall

Thread Adapters

Thread Adapters

Join threads of a different type, size, and gender

Threaded Rods

Anchor, connect, or hang components in a wide variety of applications

Press-Fit Nut Installation Tools

Press-Fit Nut Installation Tools

Everything you need to install press-fit nuts by hand

Rivet Nut Tools

Rivet Nut Tools

Install rivet nuts

Rivet Tools

Install and remove blind, solid, hollow, and other types of rivets

Building and Machinery Hardware

Cam Handles

For fast clamping, push down on the handle to draw two parts together

Power Transmission

Connecting Rods

Connecting Rods

Use with rod ends and swivel joints to link components in push/pull assemblies

Rod Ends

Use with connecting rods to support loads and control steering, tensioning, or pivoting motion

Lead Screws and Nuts

Lead Screws and Nuts

Components travel along a screw with broad, square threads to clamp and lift heavy loads

Fabricating and Machining

Clamps

Hold workpieces securely in place

Material Handling

Eyebolts

Route rope through the loop or attach hooks and shackles for lifting

The quick brown fox jumped over the lazy dog. Pedestal (35" Ht. x 4" Wd. x 4" Dp.)