These vibrators have a muffler and an air cushion prevent metal-to-metal contact.

Often attached to differential pressure gauges to measure liquid level in tanks, these manifolds have two isolation valves with a pressure-equalizing valve between them. To isolate your differential pressure gauge for maintenance or calibration, shut off flow on both sides and equalize pressure in the manifold. They are rated for at least 6,000 psi. Use with water, oil, air, and inert gas.

Pull the handle to dispense bulk material quickly through a gravity-fed, wide-mouth opening.

Choose from a variety of containers, lids, and accessories to design a dispenser that will pour or pump contents without allowing contaminants inside. These dispensers are often used with oil and other lubricating fluids.

Grab and serve food with these tongs.

Connect a tube fitting and tubing to the dispenser outlet to access hard-to-reach lubrication points.

Serve multiple lubrication points from a single location.

Serve multiple lubrication points from a single location.

Mount these reservoirs directly to your machine, or use them with a flow-adjustment valve and brush to create a dispenser.

A sealed design prevents contamination in dirty and dusty environments. Install a line between the reservoir's pressure port and the lubricated equipment to balance pressure.

Use this dispenser to brush oil on chain, gears, and conveyors. Often used to replenish lubricant after washdowns.

For use in clean environments, these manifolds have multiple air vents that keep pressure balanced.

Deliver an equal amount of oil to multiple lubrication points at once.

A solenoid automatically starts and stops flow to dispense lubricant while equipment is running.

Use these brushes to lubricate chain, gears, and conveyors. Connect to an oil dispenser, then turn the dial to adjust flow.

As chain, gears, and conveyors move, these brushes rotate to apply lubricant.

Choose from pumps that dispense with a set interval. Turn the dial to adjust the flow from 0.1 oz. to 0.2 oz. per cycle.

Ready to connect to your air system, these complete systems include a timer and a reservoir.

Connect these modular pumps to a reservoir and a solenoid valve to automate the flow of oil.

Use with manual and electric pumps to dispense different amounts of oil from multiple lubrication points.

Equipped with a flowmeter/totalizer, this dispenser displays both the flow rate and the cumulative flow volume of the oil dispensed.

Deliver a mist of oil using shop air.

These dispensers have an opening for filling without removing the nozzle.

This gun comes filled with 2 oz. of lithium-thickened grease.

Turn a small tube of grease into a dispenser.

Dispense grease with the highest-pressure-rated gun we offer.

Switch between high-pressure and low-pressure settings. Use high pressure to dispense thicker grease or to force grease through clogged fittings. Use low pressure for high-volume dispensing.

Be sure you’re using the right grease—this gun has a clear barrel for identification at a glance.

Switch between high-pressure and low-pressure settings. Use high pressure to dispense thicker grease or to force grease through clogged fittings. Use low pressure for high-volume dispensing.

Ensure that only food-grade grease is used in controlled areas—this gun only works with compatible food-grade grease cartridges.

Dispense small amounts of grease with this compact gun.

Dispense from grease guns into grease fittings and bare lubrication points.

These rigid tip adapters penetrate gaskets, sealed bearings, and joints to deliver grease to precise locations.

These flexible nozzles come with a dispensing tip and have threads on one end for connecting to a grease gun.

These flexible nozzles have threads on both ends for connecting a grease gun to a dispensing tip.

With threads on both ends, these rigid nozzles connect grease guns to dispensing tips.

Convert dispensing tips with male threads into quick-disconnect couplings.

These flexible extensions have a quick-disconnect fitting that snaps into your dispensing tip, so you can lubricate grease fittings that are hard to reach.

Mount these pumps to your grease container to bulk load guns.

Tighten the cover to dispense grease.

These dispensers come packed with grease, eliminating the mess of filling. Turn the dial to adjust flow rate.

Apply lubricant to gear racks with a 14 1/2° pressure angle and a pitch of 16.

Useful in remote areas without access to air or electrical power.

Switch between high-pressure and low-pressure settings. Use high pressure to dispense thicker grease or to force grease through clogged fittings. Use low pressure for high-volume dispensing.

Connect these guns to container-mount dispensers for controlled dispensing.

A display allows you to monitor how much grease is dispensed.

Made of neoprene rubber, these rollers resist oil, flames, gasoline, and weather.

These urethane rollers are nonmarring and wear resistant.

These urethane rollers are nonmarring and wear resistant.

These urethane rollers are wear and chemical resistant. They’re also nonmarring.

The mounting holes on these rollers are tapped directly through the roller’s surface so you can install them with set screws and still fit them into tight spots.

Use these SBR rubber rollers with a keyed shaft to prevent slippage in high-torque applications.

Made of neoprene rubber, these rollers resist oil, flames, gasoline, and weather.

These rollers spin freely in one direction and lock to transmit power in the other. Made of neoprene rubber, they are oil, flame, gasoline, and weather resistant.

These polyurethane rollers are nonmarring and wear resistant.

Made of neoprene rubber, these rollers resist oil, flames, gasoline, and weather.

Made of neoprene rubber, these rollers resist oil, flames, gasoline, and weather.

Place stands on a work surface to position pipe while machining.

Arms are long and at a wide angle to support pipe from 4" to 36" in diameter.

Rollers support and help guide material into machinery.

Use in place of ball transfers to prevent scratches when feeding and positioning flat sheets and panels.

Feed wire through the wheels inside the included counter to take measurements.

A heavy duty steel construction and long handle allow you to grip hot material in furnaces and forging and heat-treating applications.

Keep hands away from machinery—use these lightweight tools to pick up and hold parts. The pliers-style handles provide more comfort and control than standard tongs.

Get a firm grip on beakers and other containers in the curved jaws. You can also use the tips of these tongs to pick up small objects.

Often used to pick up steel sheets, the magnet holds material until you press the lever to disengage it.

Push the plunger to engage the magnet; release to disengage. These retrievers bend into position and stay in place.

Pick up objects on the ground, grab items on high shelves, and reach into deep tanks.

Access difficult-to-reach lubrication points from up to 10 ft. away.

Safer to use around energized equipment than other types of fish tape, this fiberglass tape is also round, making it more flexible than flat and oval tape to pull wire through multiple bends.

Flexible enough for pulling wire through multiple bends, this round, stainless steel tape is stiff enough to push through tough runs without backing up.