These panel-mount adapters have a female USB connection on both ends to join two USB cables.

Mount two coaxial cords of the same gender and coaxial connection directly onto a panel cutout.

Mount these adapters in a panel cutout.

Connect two stereo cords through a panel with these adapters.

Use these connectors and cords to make Ethernet connections in wet location environments.

Unlike traditional RJ45 connectors found in data centers, these connectors stand up to rugged industrial environments since they tightly thread to devices with M12 connections, sealing out contaminants and resisting shaking loose from vibration. Use them to transfer high-speed data between sensors, switches, computers, IO modules, programmable logic controllers (PLCs), and other equipment.

Connect audio equipment. These connectors mount to panels of any thickness, as long as you drill a mounting hole first.

Push these connectors together for secure Ethernet connections that are quick and easy to connect and disconnect with just one hand. You’ll know when the plug and socket are locked in place when you hear a click.

Pair these connectors with standard IEC power cords to bring power into or out of your electronic devices.

Rated IP67, these connectors create a dust- and watertight seal where they fit into the housing of power supplies, appliances, and other electronic devices. Instead of hardwiring your devices, these connectors let you plug in a standard IEC power cord and turn the power on and off with a built-in switch.

With a built-in switch, these connectors run power to appliances, power supplies, and other electronic devices while also filtering damaging EMI (electromagnetic interference).

Change AC voltage to DC voltage and bring power to electronic devices while protecting them from harmful electromagnetic interference (EMI).

Distribute power from one electronic device to several others with these connectors. By housing multiple outlets in a single unit, they save space and time spent on installation.

Use these connectors in general purpose residential and commercial applications.

A good fit for tight spaces, these connectors are also known as NEMA midget plugs. They turn to lock together when mated to prevent accidental disconnection.

Also known as twist-lock devices, these connectors withstand tough, repetitive use, and are more durable than standard turn-lock connectors. They turn to lock together when mated to prevent accidental disconnection.

Minimize signal loss between low-current devices with M8 connections.

Send power and signal to devices with M12 connections that are exposed to some of the toughest industrial stresses—from welding to metal machining and changing temperatures.

Some of the smallest signal/power connectors we offer, these connectors fit in tight spaces and are often used in electronics.

Often used to send power and signal to automated systems, motors, and pumps, these mini connectors carry higher currents than M5, M8, and M12 connectors.

Send higher current than M5, M8, and M12 connectors near tough industrial jobs, such as welding and metal machining.

Rated to MIL-DTL-5015 specifications, these connectors are compatible with other products that meet the same standard. They screw together for a secure connection.

Make secure connections with machine tools, robots, and other equipment that vibrates frequently and carries currents as high as 300 amps.

These general purpose M23 connectors send power or signal to servomotors, servocontrollers, and servodrives.

Made with industry standard barrel-style ends, these connectors carry DC power between electronic devices and power supplies.

These connectors meet international standards IEC 309-1 and 309-2. They prevent an electrical arc when separating mated connectors, so you can safely connect and disconnect with the power on.

Mount these receptacles to control cabinets and equipment in order to quickly connect and disconnect M29 power cords.

Often used in devices that branch off of the main power line, these connectors power high-amperage fans, pumps, and machines in motor controls, conveyors, and sorting and packaging systems.

With a flange on the socket end, you can mount these cords in a panel cutout to move data between computers, printers, and mobile devices.

No drilling or fasteners needed—a screw-in cover plate makes it easy to mount these chargers for powering up phones, tablets, speakers, cameras, and other small devices.

Grips have a rubber inner grommet with multiple holes and a rubber O-ring that create a tight seal to prevent liquid from entering the connection.

The face of these grips is flush with the cable-entry point for a seamless appearance. They have a thin, flexible seal that covers the holes until you push a cord through.

Modify these cord grips to get the right fit for your cord even when you don't know the exact diameter.

FDA compliant for direct food contact, these cord grips have a multi-piece design to wrap around cables in sanitary environments without removing connectors or rewiring.

The face of these grips is flush with the cable-entry point for a seamless appearance.

These grips are sized to fit in tight areas.

Wrap the split gland of these grips around ethernet cables with an RJ45 connector or other already installed cables for a water-resistant seal with your enclosure.

Because these grips resist absorbing water, they are less likely to crack or corrode than other types of plastics and metals.

Extend your cord’s life while stopping it from coming loose in places that are sanitized with water or steam as hot as 300° F, such as food plants and clean rooms.

Snap these cord grips into place to secure cable in wet environments.

Tighten the screw-down clamp for superior pull-out resistance.

These grips are made of nylon, which resists most chemicals. The nylon mesh extension provides a secure hold when the cable is pulled or in motion.

Suitable for use in applications where cords are underwater—these grips are rated IP68 for protection from prolonged submersion.

These grips have an extension that provides extra support for moving cable and prevents kinking for longer cable life.

With an oval bushing hole, these lightweight grips secure flat building cable, such as Romex and Festoon cable, in wet areas. All offer strain relief to extend cable life.

Use these lightweight grips to secure cords entering knockouts at a 45° angle in wet, tight spaces while easing the stress from bending. Made of aluminum, they’re lighter in weight than steel and brass grips yet durable.

Create a tight grip on cords in wet environments while reducing stress from bending—the 90° angle of these cord grips routes cords to fit tight spaces in enclosures and panels.

Made of nylon, these grips resist chemicals.

Built with snap-in tabs and a spring extension, these cord grips install into panel holes more quickly than standard grips and better prevent damage from sharp bends.

Able to stand up to rust better than steel grips, these 300 series stainless steel grips secure electrical cables in corrosive environments.

The mesh extension provides a secure hold in applications where cable is pulled or in motion. It reduces stress on the cable and prevents kinking for longer cable life.

Stronger than aluminum cord grips, these grips are zinc plated for corrosion resistance.

These cord grips are lightweight yet durable.

Made of nylon, these grips resist chemicals. Install them in panels and enclosures—they have a zinc-plated steel locknut and metal-reinforced rubber O-ring that prevents liquid from entering the enclosure.

Made of nylon, these grips resist chemicals. Install them in panels and enclosures—they have a zinc-plated steel locknut and metal-reinforced rubber O-ring that prevents liquid from entering the enclosure.

These cord grips are lightweight yet durable. They have a zinc-plated steel locknut and metal-reinforced rubber O-ring that prevents liquid from entering the connection.

These cord grips are lightweight yet durable. They have a zinc-plated steel locknut and metal-reinforced rubber O-ring that prevents liquid from entering the connection.

Secure cords in wet and industrial environments with little room—these grips curve 45° to relieve bending stress.

These grips are nickel-plated brass for good corrosion resistance.

These grips meet Class III, Divisions 1 and 2 standards for use in hazardous locations.

Already mounted in a conduit box, these connection strips save you the effort of modifying a panel for installation.

Create a connection point on a control panel to plug in thermocouples.

No need to take these connectors apart—just insert your wire leads and tighten the terminals to quickly give your thermocouple a plug-in connection.