About Durometer Hardness Scales
More
About Leveling Mounts
More
About Vibration-Damping Mounts
More
Nickel-Plated Steel Swivel Leveling Mounts with Threaded Stud
Nickel-plated steel has some corrosion resistance. Mounts have a ball-and-socket design that swivels to compensate for uneven floors. In addition to leveling, mounts raise equipment off the floor for easier cleaning and inspection.
Mounts with a cushion are nonskid for an extra measure of stability.
For technical drawings and 3-D models, click on a part number.
Metric Yellow Zinc-Plated Steel Swivel Leveling Mounts with Threaded Stud
Yellow zinc-plated steel is more corrosion resistant than nickel-plated steel. Mounts have a ball-and-socket design that swivels to compensate for uneven floors. In addition to leveling, mounts raise equipment off the floor for easier cleaning and inspection.
Mounts with a cushion are nonskid for an extra measure of stability.
For technical drawings and 3-D models, click on a part number.
Metric Corrosion-Resistant Swivel Leveling Mounts with Threaded Stud
Made entirely of stainless steel, these mounts resist corrosion from water and most chemicals. Their ball-and-socket design swivels to compensate for uneven floors. In addition to leveling, mounts raise equipment off the floor for easier cleaning and inspection.
Mounts with a cushion are nonskid for an extra measure of stability.
For technical drawings and 3-D models, click on a part number.
Metric Super-Corrosion-Resistant Swivel Leveling Mounts with Threaded Stud
Made entirely of 316 stainless steel, these mounts have superior corrosion resistance. Their ball-and-socket design swivels to compensate for uneven floors. In addition to leveling, mounts raise equipment off the floor for easier cleaning and inspection.
For technical drawings and 3-D models, click on a part number.
Thread Size | Thread Pitch, mm | Thread Lg., mm | Capacity per Mount, lbs. | Base Dia., mm | Overall Ht., mm | Hex Nut Wd., mm | Each | |
316 Stainless Steel | ||||||||
---|---|---|---|---|---|---|---|---|
M20 | 2.5 | 51 | 7,370 | 76 | 89 | 27 | 0000000 | 0000000 |
Metric Bolt-Down Swivel Leveling Mounts with Threaded Stud
Punch-out holes in the base let you bolt down these mounts to keep your equipment stationary. Their ball-and-socket design swivels to compensate for uneven floors. In addition to leveling, mounts raise equipment off the floor for easier cleaning and inspection.
Mounts with a cushion are nonskid for an extra measure of stability.
For technical drawings and 3-D models, click on a part number.
Mounting Holes | |||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Thread Size | Thread Pitch, mm | Thread Lg., mm | Capacity per Mount, lbs. | Base Dia., mm | Overall Ht., mm | Hex Nut Wd., mm | Temperature Range, °F | Mounting Fasteners Included | No. of | Dia., mm | Ctr.-to-Ctr. Lg., mm | Each | |
Plastic with Zinc-Plated Steel Stud | |||||||||||||
M20 | 2.5 | 102 | 5,000 | 76 | 130 | 27 | -20° to 170° | No | 2 | 8.9 | 55.9 | 0000000 | 000000 |
M20 | 2.5 | 102 | 7,500 | 102 | 135 | 27 | -20° to 170° | No | 2 | 11.9 | 68.8 | 0000000 | 00000 |
M20 | 2.5 | 152 | 5,000 | 76 | 181 | 27 | -20° to 170° | No | 2 | 8.9 | 55.9 | 00000000 | 00000 |
M20 | 2.5 | 152 | 7,500 | 102 | 185 | 27 | -20° to 170° | No | 2 | 11.9 | 68.8 | 0000000 | 00000 |
M20 | 2.5 | 152 | 10,000 | 127 | 210 | 27 | -20° to 170° | No | 2 | 12 | 98 | 0000000 | 00000 |
M20 | 2.5 | 203 | 5,000 | 76 | 232 | 27 | -20° to 170° | No | 2 | 8.9 | 55.9 | 00000000 | 00000 |
M20 | 2.5 | 203 | 7,500 | 102 | 236 | 27 | -20° to 170° | No | 2 | 11.9 | 68.8 | 00000000 | 00000 |
M20 | 2.5 | 203 | 10,000 | 127 | 260 | 27 | -20° to 170° | No | 2 | 12 | 98 | 00000000 | 00000 |
M20 | 2.5 | 254 | 10,000 | 127 | 311 | 27 | -20° to 170° | No | 2 | 12 | 98 | 00000000 | 00000 |
Plastic with Rubber Cushion and Zinc-Plated Steel Stud | |||||||||||||
M20 | 2.5 | 102 | 5,000 | 76 | 131.6 | 27 | -20° to 170° | No | 2 | 8.9 | 55.9 | 00000000 | 00000 |
M20 | 2.5 | 102 | 7,500 | 102 | 136.6 | 27 | -20° to 170° | No | 2 | 11.9 | 68.8 | 00000000 | 00000 |
M20 | 2.5 | 152 | 5,000 | 76 | 182.6 | 27 | -20° to 170° | No | 2 | 8.9 | 55.9 | 00000000 | 00000 |
M20 | 2.5 | 152 | 7,500 | 102 | 186.6 | 27 | -20° to 170° | No | 2 | 11.9 | 68.8 | 0000000 | 00000 |
M20 | 2.5 | 203 | 5,000 | 76 | 233.6 | 27 | -20° to 170° | No | 2 | 8.9 | 55.9 | 00000000 | 00000 |
M20 | 2.5 | 203 | 7,500 | 102 | 237.6 | 27 | -20° to 170° | No | 2 | 11.9 | 68.8 | 00000000 | 00000 |
M20 | 2.5 | 254 | 10,000 | 127 | 312.6 | 27 | -20° to 170° | No | 2 | 12 | 98 | 000000 | 00000 |
Metric Corrosion-Resistant Bolt-Down Swivel Leveling Mounts with Threaded Stud
Well-suited to damp environments, these mounts have a stainless steel stud and nut for corrosion resistance. Use the punch-out holes in the base to bolt down mounts to keep your equipment stationary. Their ball-and-socket design swivels to compensate for uneven floors. In addition to leveling, mounts raise equipment off the floor for easier cleaning and inspection.
Mounts with a cushion are nonskid for an extra measure of stability.
For technical drawings and 3-D models, click on a part number.
Mounting Holes | |||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Thread Size | Thread Pitch, mm | Thread Lg., mm | Capacity per Mount, lbs. | Base Dia., mm | Overall Ht., mm | Hex Nut Wd., mm | Temperature Range, °F | Mounting Fasteners Included | No. of | Dia., mm | Ctr.-to-Ctr. Lg., mm | Each | |
Plastic with 303 Stainless Steel Stud | |||||||||||||
M20 | 2.5 | 152 | 7,500 | 102 | 185 | 27 | -20° to 170° | No | 2 | 11.9 | 68.8 | 0000000 | 000000 |
Plastic with Rubber Cushion and 303 Stainless Steel Stud | |||||||||||||
M20 | 2.5 | 152 | 7,500 | 102 | 186.6 | 27 | -20° to 170° | No | 2 | 11.9 | 68.8 | 0000000 | 00000 |
Metric Yellow Zinc-Plated Steel Swivel Leveling Mounts with Threaded Hole
Yellow zinc-plated steel is more corrosion resistant than nickel-plated steel. Mounts have a ball-and-socket design that swivels to compensate for uneven floors. Add your own threaded stud or bolt to build a mount that fits your needs. In addition to leveling, mounts raise equipment off the floor for easier cleaning and inspection.
Mounts with a cushion are nonskid for an extra measure of stability.
For technical drawings and 3-D models, click on a part number.
Metric Corrosion-Resistant Swivel Leveling Mounts with Threaded Hole
Made of stainless steel, these mounts resist corrosion from water and most chemicals. Their ball-and-socket design swivels to compensate for uneven floors. Add your own threaded stud or bolt to build a mount that fits your needs. In addition to leveling, mounts raise equipment off the floor for easier cleaning and inspection.
Mounts with a rubber cushion are nonskid for an extra measure of stability.
For technical drawings and 3-D models, click on a part number.
Thread Size | Thread Pitch, mm | Thread Dp., mm | Capacity per Mount, lbs. | Base Dia., mm | Overall Ht., mm | Hex Nut Wd., mm | Temperature Range, °F | Performance | Each | |
303 Stainless Steel | ||||||||||
---|---|---|---|---|---|---|---|---|---|---|
M20 | 2.5 | 13.9 | 7,370 | 76 | 38 | 27 | -20° to 170° | Corrosion Resistant | 0000000 | 000000 |
303 Stainless Steel with Rubber Cushion | ||||||||||
M20 | 2.5 | 13.9 | 5,555 | 76 | 41 | 27 | -20° to 170° | Antislip, Corrosion Resistant | 0000000 | 00000 |
Corrosion-Resistant Swivel Vibration-Damping
Leveling Mounts with Threaded Stud
All-stainless steel construction stands up to water and chemicals and won't rust or corrode. Use these mounts to minimize vibration and noise to prolong machine life and protect floors. Their ball-and-socket design swivels to compensate for uneven floors. In addition to leveling, mounts raise equipment off the floor for easier cleaning and inspection.
For technical drawings and 3-D models, click on a part number.
Thread Size | Thread Pitch, mm | Thread Lg. | Capacity per Mount, lbs. | Deflection @ Capacity | Base Dia. | Overall Ht. | Temperature Range, °F | Each | |
304 Stainless Steel with Rubber Cushion | |||||||||
---|---|---|---|---|---|---|---|---|---|
M20 | 2.5 | 4 3/4" | 1,000 | 0.12" | 3 7/8" | 5 11/16" | 0° to 200° | 0000000 | 000000 |
M20 | 2.5 | 4 3/4" | 2,000 | 0.12" | 3 7/8" | 6 5/16" | 0° to 200° | 0000000 | 00000 |
M20 | 2.5 | 4 3/4" | 3,000 | 0.17" | 5 1/2" | 6 7/8" | -20° to 190° | 00000000 | 000000 |
M20 | 2.5 | 4 3/4" | 4,000 | 0.17" | 5 1/2" | 6 9/16" | -20° to 190° | 0000000 | 000000 |
Sanitary Swivel Vibration-Damping Leveling Mounts with Threaded Stud
Thread these mounts into machinery to level them on uneven floors in sanitary environments such as food-processing areas. They also create space to clean underneath machinery. All have a hygienic thread cover that prevents contaminants from settling in the grooves. To further block out contaminants as the mount moves, as well as prevent unsanitary metal-to-metal connections, there is a silicone seal at each end of the thread cover and at the point where the mount swivels. These seals have chemical additives, so you can find them with an X-ray machine if a piece falls into your line. This helps you comply with Hazard Analysis and Critical Control Point (HACCP) programs to keep contaminated food from leaving your facility. Seals are also FDA compliant for direct contact with food.
Made of 304 stainless steel, these mounts won’t corrode from frequent washdowns with harsh cleaners and sanitizers. Their smooth finish and rounded edges leave no crevices for bacteria to grow in, reducing the chance of foodborne illnesses. They also don’t have any horizontal ledges, so liquids and food will drain off completely. Certified by 3-A, EHEDG, and USDA, they meet sanitary design standards.
The rubber cushion on the bottom reduces vibration and noise from machinery, which protects floors and extends machine life. Their grip on the floor minimizes bacteria growth beneath them and prevents machines from shifting.
These mounts swivel to level machinery on slightly uneven floors; for severely uneven floors, use the threaded stud to raise each mount to a level height.
Some mounts have mounting holes to secure them to the floor, keeping machinery stationary. Mounts with one mounting hole are secure enough to prevent machines from moving while they’re running and being cleaned.
For technical drawings and 3-D models, click on a part number.
Mounting Holes | |||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Thread Size | Thread Lg. | Mounting Ht. | Cap. per Mount, lbs. | Deflection @ Cap. | Swivel Range of Motion | Base Dia. | Overall Ht. | Temp. Range, °F | Mounting Fasteners Included | Dia. | Performance Properties | Specifications Met | Performance | Each | |
304 Stainless Steel with Rubber Cushion | |||||||||||||||
M20 | 8 1/4" | 5 1/2"-8 1/16" | 3,300 | Not Rated | 10° | 3 1/8" | 9 9/16" | -30° to 230° | __ | __ | X-Ray Detectable | 3-A Certified 88-00, EHEDG Certified, FDA Compliant 21 CFR 177.2600, USDA Accepted Equipment | Antislip, Vibration Damping | 0000000 | 000000 |
304 Stainless Steel with Rubber Cushion—One Mounting Hole | |||||||||||||||
M20 | 5 7/8" | 4 5/16"-5 11/16" | 3,300 | Not Rated | 10° | 3 1/8" | 7 3/16" | -30° to 230° | No | 19/32" | X-Ray Detectable | 3-A Certified 88-00, EHEDG Certified, FDA Compliant 21 CFR 177.2600, USDA Accepted Equipment | Antislip, Vibration Damping | 0000000 | 000000 |
Bolt-Down Swivel Vibration-Damping Leveling Mounts with Threaded Stud
Bolt these mounts down to keep your equipment stationary. Use them to minimize vibration and noise to prolong equipment life and protect floors. Mounts have a ball-and-socket design that swivels to compensate for uneven floors. In addition to leveling, mounts raise equipment off the floor for easier cleaning and inspection. They're made of stainless steel for corrosion resistance when exposed to water and most chemicals.
Mounts with one mounting hole are good for tight locations.
For technical drawings and 3-D models, click on a part number.
Thread Size | Thread Pitch, mm | Thread Lg. | Capacity per Mount, lbs. | Deflection @ Capacity | Base Dia. | Base Ht. | Overall Ht. | Temperature Range, °F | Mounting Fasteners Included | Mount. Hole Dia. | Each | |
304 Stainless Steel with Rubber Cushion | ||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|
One Mounting Hole | ||||||||||||
M20 | 2.5 | 5 15/16" | 1,770 | 0.06" | 2 15/16" | 7/8" | 6 13/16" | 0° to 200° | No | 5/8" | 00000000 | 000000 |
Extreme-Force Swivel Vibration-Damping Leveling Mounts with Threaded Stud
Higher deflection ratings translate to greater vibration and shock isolation. These mounts have a rubber base that grips the floor for stability and is resistant to oil and grease. Their ball-and-socket design swivels to compensate for uneven floors. In addition to leveling, mounts raise equipment off the floor for easier cleaning and inspection.
For technical drawings and 3-D models, click on a part number.
Thread Size | Thread Pitch, mm | Thread Lg. | Capacity per Mount, lbs. | Deflection @ Capacity | Swivel Range of Motion | Base Dia. | Base Ht. | Overall Ht. | Hardness | Hardness Rating | Temp. Range, °F | Each | |
Rubber with Zinc-Plated Steel Stud | |||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|
M20 | 2.5 | 4 1/4" | 3,700 | 0.13" | 7.5° | 5" | 1 1/2" | 5 7/8" | Durometer 50A | Medium | -20° to 180° | 00000000 | 0000000 |
M20 | 2.5 | 4 1/4" | 8,000 | 0.13" | 7.5° | 5" | 1 1/2" | 5 7/8" | Durometer 70A | Hard | -20° to 180° | 00000000 | 000000 |
Fail-Safe Bolt-Down Vibration-Damping Mounts with Threaded Hole
An interlocking steel frame in these mounts prevents collapse, even if the rubber fails. They minimize vibration and noise from machinery to reduce maintenance costs, prolong equipment life, and protect floors. Use the holes in the base to bolt down these mounts to keep your equipment stationary. Neoprene rubber has good resistance to oil and gasoline.
For technical drawings and 3-D models, click on a part number.
Mounting Holes | |||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Thread Size | Thread Pitch, mm | Capacity per Mount, lbs. | Deflection @ Capacity | O'all Ht. | Dia. | Base Lg. | Base Wd. | Hardness | Temp. Range, °F | Mounting Fasteners Included | No. of | Dia. | Ctr.-to-Ctr. | Each | |
Neoprene Rubber with Steel Base | |||||||||||||||
M20 | 2.5 | 900 | 0.13" | 1.84" | 3.1" | 6.41" | 4.09" | Durometer 30A | 10° to 180° | No | 2 | 0.53" | 5" | 000000000 | 000000 |
M20 | 2.5 | 1,106 | 0.13" | 1.84" | 3.1" | 6.41" | 4.09" | Durometer 40A | 10° to 180° | No | 2 | 0.53" | 5" | 000000000 | 00000 |
M20 | 2.5 | 1,630 | 0.13" | 1.84" | 3.1" | 6.41" | 4.09" | Durometer 50A | 10° to 180° | No | 2 | 0.53" | 5" | 000000000 | 00000 |
M20 | 2.5 | 2,500 | 0.13" | 1.84" | 3.1" | 6.41" | 4.09" | Durometer 60A | 10° to 180° | No | 2 | 0.53" | 5" | 000000000 | 00000 |
Metric High-Capacity Leveling Mount Inserts for Tubular Legs
Rated for high load capacity, use these inserts to connect threaded leveling mounts to machinery, instrument bases, and conveyor equipment with tubular legs. These inserts have pass-through holes that are partially threaded at the base. Tap mounts into place with a rubber hammer.
For technical drawings and 3-D models, click on a part number.
Threaded Bumpers
Mount these bumpers on a threaded stud. All are reinforced with a steel core or base plate for strength. Often used as feet, spacers, and vibration dampers, they absorb shock to prevent damage to equipment and surfaces. They're also good for starting and stopping motion on automated machines. All of these bumpers can be used outdoors.
Bumpers with an extra-hard, hard, and medium-hard rating withstand high levels of impact. The harder the bumper, the more impact it withstands.
Polyurethane bumpers have better abrasion resistance than neoprene bumpers. They won't become brittle and crack when exposed to ozone.
For technical drawings and 3-D models, click on a part number.
Thread | ||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|
Size | Pitch | Dp. | OD | Ht. | Temp. Range, °F | For Use Outdoors | Hardness Rating | Hardness | Nonmarking | Color | Each | |
Polyurethane Rubber with Steel Core | ||||||||||||
M20 | 2.5 mm | 25mm | 57mm | 57mm | -40° to 200° | Yes | Extra Hard | Durometer 95A | No | Black | 00000000 | 000000 |
Swiveling Tips for Screws and Threaded Studs
Attach to the end of a screw or threaded stud to apply uniform pressure on uneven and angled surfaces. Also known as toggle and swivel-foot pads.
For technical drawings and 3-D models, click on a part number.
Dia. | Ht. | Load Capacity, lbs. | Thread Size | Range of Motion | Each | |
Steel | ||||||
---|---|---|---|---|---|---|
32mm | 36mm | 4,720 | M20 | 20° | 0000000 | 000000 |