These metric Grade B7 threaded rods meet the pressure and temperature requirements of ASTM A193 and are often used to secure pressure tanks, valves, and flanges.

Tighten these threaded rods by turning them to the left; once fastened, they resist loosening from counterclockwise motion.

Grade B16 threaded rods maintain their strength at higher temperatures than Grade B7 threaded rods. They meet the pressure and temperature requirements of ASTM A193 and are often used to secure pressure tanks, valves, and flanges.

These metric threaded rods are about half the strength of medium-strength steel threaded rods for light duty hanging, mounting, and fastening.

Tighten these threaded rods by turning them to the left; once fastened, they resist loosening from counterclockwise motion. About half the strength of medium-strength steel threaded rods, use them for light duty hanging, mounting, and fastening.

Comparable to Grade 8 steel, these threaded rods have a tensile strength of 150,000 psi, making them about 25% stronger than medium-strength steel rods.

Class 12.9 rods are about 20% stronger than Class 10.9 threaded rods and are for use in heavy machinery.

Available in metric sizes, these 18-8 stainless steel threaded rods have good chemical resistance.

Grade B8 threaded rods meet the pressure and temperature requirements of ASTM A193 and are often used to secure pressure tanks, valves, and flanges. They have good chemical resistance.

More corrosion resistant than 18-8 and 410 stainless steel threaded rods, these 316 stainless steel rods have excellent resistance to chemicals and salt water.

Tighten these threaded rods by turning them to the left; once fastened, they resist loosening from counterclockwise motion.

These hardened 316 stainless steel threaded rods are 40% stronger than standard Grade B8M threaded rods. They meet the pressure and temperature requirements of ASTM A193 and are often used to secure pressure tanks, valves, and flanges.

One-third the weight of steel, aluminum threaded rods resist corrosion in wet environments.

These metric brass threaded rods are corrosion resistant in wet environments, electrically conductive, and nonmagnetic.

These metric threaded rods are made from nylon 6/6 and resist oil, grease, and solvents. They’re nonconductive, making them good for use around sensitive electrical components.

Unlike metal rods, these metric threaded rods will not warp at extreme temperatures, making them ideal for heat treating and furnace fixtures.

PTFE threaded rods withstand temperatures up to 250° F and resist oil, grease, detergents, and most mineral acids. They're the lowest friction plastic threaded rods we offer, so they thread on smoothly.

PVC threaded rods resist acids, alkalies, salt solutions, and alcohol.

Commonly used in valves, pumps, and shafts, these 400 nickel threaded rods resist salt water and caustic chemicals.

Titanium threaded rods have a high strength-to-weight ratio and are resistant to acids and salt water.

These steel studs are zinc plated to resist corrosion in wet environments.

Screw these studs into a tapped hole and use them as a pivot point, hinge, shaft, or locator pin.

Also known as hood pins, these studs have a cotter pin lodged through a drilled hole in the unthreaded portion for light duty holding, such as securing access panels and locking other fasteners.

316 stainless steel studs have excellent resistance to chemicals and salt water.

These studs have good chemical resistance. Weld them to stainless steel surfaces.

18-8 stainless steel studs have good chemical resistance and may be mildly magnetic. Also known as hanger bolts, use them to hang, mount, and fasten parts to wood structures.

These studs are also known as hanger bolts—use them to hang, mount, and fasten parts to wood structures.

Add a stud to thin material when you only have access to one side.

A hollow center allows these studs to be used as an axle, a vent, or a passageway for wiring.

Often used in cell phones and laptops, these pins attach thin panels such as printed circuit boards to metal and plastic bases. Also known as PEM® TA and T4 TackPins.

Pass these pins through a mounting hole and weld the head to the surface.

Press these wing head nuts into a closed-end hole or thick panel in applications where the back of the panel is inaccessible. A quarter-turn locks and releases access panels, doors, and covers.

Press these wing head nuts into the backside of a panel in applications where you have access to both sides of the panel. A quarter-turn locks and releases access panels, doors, and covers.

Rivet these wing head nuts into thin panels for a flush fit. They can be mounted without space between panels. A quarter-turn locks and releases access panels, doors, and covers.

These wing-head screws have a clip-on nut that allows you to mount them near the edge of a thin panel. Use them to lock and release access panels, doors, and covers with a quarter-turn.