The most widely used aluminum, 6061 is fabricated into everything from pipe fittings and containers to automotive and aerospace parts. It is strong and corrosion resistant, plus it's easy to machine and weld.

Polished on the outside to a #8 reflective, mirror-like finish, these tubes have no visible grain lines.

The most widely used aluminum, 6061 is fabricated into everything from pipe fittings and containers to automotive and aerospace parts. It is strong and corrosion resistant, plus it's easy to machine and weld.

More corrosion resistant and easier to form than multipurpose 6061 aluminum, 6063 is primarily used for exterior railings, decorative trim, and door frames.

The outside of these tubes is anodized to improve wear and corrosion resistance.

Known for being one of the easiest types of aluminum to weld, 5052 is also recognized for its ability to resist salt water. It's widely used for the bodies of boats, buses, trucks, and trailers, as well as for chemical drums.

3003 aluminum stands up to outdoor use, as well as exposure to chemicals. It offers a good combination of strength, formability, and weldability. It's often used for storage tanks, heat exchangers, and general sheet metal work.

Also known as mild steel, low-carbon steel is easy to machine, form, and weld. It's widely fabricated into parts that don’t require high strength.

The same steel used in automobile bodies, this AHSS (advanced high-strength steel) allows you to fabricate high-strength parts using thinner material than you could with other types of steel. It is formable, weldable, and more economical than alloy steel.

4130 alloy steel has a low carbon content that provides good weldability. It's often used for gears, fasteners, and structural applications.

Easier to machine than 52100 alloy steel rods, these extremely hard and wear-resistant tubes are often used to create bearings, bushings, and other cylindrical parts that are under constant stress. They’re also known as chrome steel.

From cookware to chemical-processing equipment, 304 stainless steel is a good all-around choice for a wide range of applications.

The textured surface hides fingerprints and dents. This material is widely used in decorative applications, such as partitions and handrails.

With 99.99% copper content, 101 copper has higher purity than 110 copper, resulting in superior electrical conductivity. It's commonly called OFE and OFHC copper. Use it in electrical applications, such as for coaxial cables and terminal lugs.

The addition of phosphorus makes 122 copper easier to weld and braze than 110 copper. It has excellent resistance to corrosion caused by water, soil, and weather, making it the go-to material for plumbing and underground applications.

The most formable brass we offer, 260 offers better weldability than 300 series brass but it’s not as machinable. Sometimes called cartridge brass, it's commonly used for ammunition casings, radiator components, and decorative door hardware.

Offering the highest yield strength of all our brass, 330 has a low lead content for a good balance of machinability and formability. It's used for fire station poles, pump cylinder lines, and plumbing accessories.

Offering excellent antifriction qualities, 932 bronze also offers good strength and wear resistance. It's also known as SAE 660 and is often used for bearings, bushings, and thrust washers.

An excellent alternative to oil-filled bronze, graphite-filled bronze provides dry lubrication in temperatures as high as 700° F.

In addition to a low-friction surface that prevents sticking and binding, this tough material is impact and wear resistant to handle the scuffs, scrapes, and strikes that other plastics can’t.

The addition of PTFE provides a more slippery, wear-resistant surface than standard Delrin® acetal resin. It’s commonly fabricated into pump components, gears, and bearings.

Because PVC resists many acids and alkalies, it’s widely used for tanks and in chemical-processing applications. Also known as PVC Type 1.

Also known as nylon 6/6, this general purpose material is often used for bearings, gears, valve seats, and other high-wear parts.

This cast nylon 6 material is easier to machine than other types of nylon. It’s comparable to Nylatron and Nycast.

This nylon stays lubricated over time because it’s filled with oil. Use it to fabricate parts for hard-to-reach places where adding lubricants would be difficult.

Because this polypropylene resists swelling when exposed to water, it’s often fabricated into containers and parts for laboratory equipment.

This glass-filled PTFE is more rigid than standard PTFE for increased durability in high-stress applications.

Cast acrylic is easier to machine than extruded acrylic. It's comparable to Lucite and Plexiglas® Acrylic.

At only half the weight of glass, polycarbonate maintains excellent impact resistance across a wide temperature range. It's comparable to Lexan, Hyzod, Tuffak, and Makrolon.

Add rollers to T-slotted framing to create flow rails, ball transfer tables, and other manual conveyors.

Reduce the chance your concrete will crack from expansion and contraction and other tensile stresses.

A good all-around choice, Garolite G-10/FR4 is strong, machinable, and electrically insulating. It meets UL 94 V-0 for flame retardance.

A good all-around choice, Garolite G-10/FR4 is strong, machinable, and electrically insulating. It meets UL 94 V-0 for flame retardance.

With a coating that reduces static electricity , these sheets are good for use in solder pallets, automated test equipment, electronic assembly workstations, and other applications where static buildup could damage your equipment.

These rectangular tubes are flame retardant, machinable, and electrically insulating.

Garolite CE is often fabricated into parts where high strength is not required.

Graphite is added to this Garolite CE to provide a slippery surface that reduces friction and makes this material conductive.

Use Garolite G-10 in place of Garolite G-10/FR4 for applications that are sensitive to halogen, such as in nuclear plants. It's strong, machinable, and electrically insulating.

Stronger than Garolite CE with better electrical-insulating properties, Garolite XX is often fabricated into low-cost electrical components.

Stronger than Garolite CE with better electrical-insulating properties, Garolite XX is often fabricated into low-cost electrical components.

Using nothing more than standard high-speed steel tooling, Garolite LE can be machined into intricate parts.

Easily turn these rectangular tubes into parts for transformers and switchgears using high-speed tooling.

Offering higher strength and better heat resistance than Garolite G-10/FR4, Garolite G-11 is suitable for continuous use in elevated temperatures.

Good for use as structural mounting brackets, components, and electrical housings in high temperatures, these angles are a flame-retardant version of Garolite G-11. All are stronger and resist heat better than Garolite G-10/FR4.