Stop active leaks of up to 50 gallons per minute in concrete, brick, and stone. These crack fillers begin to harden within seconds to create a permanent fix that won't shrink. When fully cured they create a seal that can withstand pressure of up to 2,000 psi. Apply with a dispensing gun (sold separately). The size listed is the combined total of the two parts. A mixer nozzle is included.

Stop slow-flowing and weeping leaks in concrete. These crack fillers begin to harden in three to five minutes to create a permanent fix that won't shrink.

Polyurethane fillers are thin to penetrate deep into cracks. When fully cured they create a seal that can withstand pressure of up to 2,000 psi. Apply with a standard caulk gun (sold separately). For especially large cracks, use a packer (sold separately) with a grease gun or a grout pump.

Fill in and shape horizontal, vertical, and overhead concrete surfaces, such as steps and columns.

Epoxy surface fillers are nonsagging. They resist oil, grease, water, alkalies, and chemicals. Application time, after mixing, is 1 hour. The size listed is the combined total of the two parts.

Used on ceramic, concrete, and stone floor and wall tiles, grout consists of fine sand, masonry cement, and coloring. Apply with a grout float.

Acrylic grout does not require mixing. It resists shrinking, cracking, and staining.

Mix this two-part epoxy—a resin-aggregate blend and a pigmented hardener—to create a grout that resists chemicals, such as acids, alkalies, salt water, and common solvents and cleaners. Its lightweight formula makes this grout easy to spread. Use in horizontal or vertical joints—grout won’t sag or shrink. Apply with a grout float. It can be cleaned up with water when wet; it doesn’t require a sealer once it cures. The size listed is the combined total of the two parts.

Keep the surface of your porcelain fixtures looking like new.

Filler repairs large chips and cracks. Sand and finish with glaze.

Glaze touches up small chips and scratches.

Apply these sealants in cold temperatures, on wet surfaces, and even through running water. They are structural sealants that combine the mechanical strength of an adhesive with excellent sealing properties and high flexibility. Sealants are non-sagging, so they won't drip from vertical and overhead surfaces.

Elongation and joint compression/expansion tolerance indicate flexibility—the higher the values are, the more joint movement sealants can sustain. These sealants are good for use between dissimilar materials and in environments with wide temperature fluctuation.

These structural sealants combine the mechanical strength of an adhesive with excellent sealing properties and high flexibility. They’re non-sagging, so they won't drip from vertical and overhead surfaces.

Elongation and joint compression/expansion tolerance indicate flexibility—the higher the values are, the more joint movement sealants can sustain. For joints between dissimilar materials and in environments with wide temperature fluctuation, choose a sealant with a higher elongation or joint compression/expansion tolerance. For high-wear applications, choose a harder sealant for the most abrasion resistance.

Made from silicone, these sealants are RTV (room-temperature vulcanizing). They’re non-sagging, so they won't drip from vertical and overhead surfaces.

Elongation and joint compression/expansion tolerance indicate flexibility—the higher the values are, the more joint movement sealants can sustain. Sealants that are good for joining dissimilar materials also work well in environments with wide temperature fluctuation.

Also known as neutral-cure sealants, these won't discolor copper, brass, and concrete. They’re non-sagging, so they won't drip from vertical and overhead surfaces. Made from silicone, sealants are RTV (room-temperature vulcanizing).

Elongation and joint compression/expansion tolerance indicate flexibility—the higher the values are, the more joint movement sealants can sustain. Sealants that are good for joining dissimilar materials also work well in environments with wide temperature fluctuation.

Sealants that cannot be sold to California exceed local regulatory limits on VOCs (volatile organic compounds).

These sealants are non-sagging, so they won't drip from vertical and overhead surfaces.

Elongation and joint compression/expansion tolerance indicate flexibility. For joints between dissimilar materials and in environments with wide temperature fluctuation, choose a sealant with a higher elongation or joint compression/expansion tolerance. For high-wear applications, choose a harder sealant for the most abrasion resistance.

Form seals that resist punctures, cuts, and abrasion to withstand heavy wear and tampering. These sealants are non-sagging, so they won't drip from vertical and overhead surfaces.

Elongation and joint compression/expansion tolerance indicate flexibility—the higher the values are, the more joint movement sealants can sustain. These sealants are best suited to joints between similar materials that aren't exposed to wide temperature fluctuation.

Caulk is non-sagging, so it won't drip from vertical and overhead surfaces.

Elongation and joint compression/expansion tolerance indicate flexibility—the higher the values are, the more joint movement a sealant can sustain. Caulk is best suited to joints between similar materials that aren't exposed to wide temperature fluctuation.

Mix a small amount of water-based paint with this caulk to match the color of your surface. Caulk is non-sagging, so it won't drip from vertical and overhead surfaces.

Elongation and joint compression/expansion tolerance indicate flexibility—the higher the values are, the more joint movement a sealant can sustain. This caulk is best suited to joints between similar materials that aren't exposed to wide temperature fluctuation.

Impervious to the swelling effects of oils, fuels, and solvents, use this high-strength silicone sealant to assemble and repair fuel systems and tanks. Silicone forms a tough, rubbery, UV-resistant seal that remains flexible over time. It's non-sagging, so it won't drip from vertical and overhead surfaces. Also known as RTV (room-temperature vulcanizing).

Elongation and joint expansion/compression tolerance indicate flexibility—the higher the values are, the more joint movement sealants can sustain. This sealant is best suited to joints between similar materials that aren't exposed to wide temperature fluctuation.

Thinner than non-sagging sealants, these flow easily into cracks and have a smooth finish.

Elongation and joint expansion/compression tolerance indicate flexibility. For joints between dissimilar materials and in environments with wide temperature fluctuation, choose a sealant with a higher elongation or joint expansion/compression tolerance. For high-wear applications, choose a harder sealant for the most abrasion resistance.

Sealants that cannot be sold to California exceed local regulatory limits on VOC (volatile organic compounds).

The textured finish matches concrete surfaces. These sealants are non-sagging, so they won't drip from vertical and overhead surfaces.

Elongation and joint compression/expansion tolerance indicate flexibility—the higher the values are, the more joint movement sealants can sustain. These sealants are best suited to joints between similar materials that aren't exposed to wide temperature fluctuation. For high-wear applications, choose a harder sealant for the most abrasion resistance.

When Sika Sikaflex Polyurethane requires a primer, for best results use Primer 260 on metal and Primer 449 on plastic and rubber.

Primer 260 cannot be sold to CT, DC, DE, MA, MD, ME, NJ, NY, PA, RI, UT, VT; Northern VA; Los Angeles County, CA; Orange County, CA; Riverside County, CA; or San Bernardino County, CA, due to regulatory limits on VOCs (volatile organic compounds).

Seal concrete joints in high-traffic locations—these sealants stand up to heavy wear and tear, such as steel wheel traffic. Thinner than non-sagging sealants, these flow easily into cracks and have a smooth finish.

Silicone sealant is RTV (room-temperature vulcanizing).

Elongation and joint compression/expansion tolerance indicate flexibility—the higher the values are, the more joint movement sealants can sustain. These sealants are best suited to joints between similar materials that aren't exposed to wide temperature fluctuation. For high-wear applications, choose a harder sealant for the most abrasion resistance.

When Sika Sikaflex Polyurethane requires a primer, for best results use Primer 260 on metal and Primer 449 on plastic and rubber.

Seal concrete joints in high-traffic areas—these sealants stand up to heavy wear and tear, such as steel wheel traffic. They're non-sagging, so they won't drip from vertical and overhead surfaces. Made from silicone, sealants are RTV (room-temperature vulcanizing).

Elongation and joint compression/expansion tolerance indicate flexibility—the higher the values are, the more joint movement sealants can sustain. These sealants are best suited to joints between similar materials that aren't exposed to wide temperature fluctuation. For high-wear applications, choose a harder sealant for the most abrasion resistance.

Apply these sealants on wet surfaces and in cold temperatures. Thinner than non-sagging sealants, these flow easily into cracks and have a smooth finish.

Elongation and joint compression/expansion tolerance indicate flexibility—the higher the values are, the more joint movement sealants can sustain.

Apply these sealants on wet surfaces and in cold temperatures. They're non-sagging, so they won't drip from vertical and overhead surfaces.

Elongation and joint compression/expansion tolerance indicate flexibility—the higher the values are, the more joint movement sealants can sustain. These sealants are best suited to joints between similar materials that aren't exposed to wide temperature fluctuation.

Keep out the elements by sealing roof joints. These sealants are non-sagging, so they won't drip from vertical and overhead surfaces. They are good for use in environments with wide temperature fluctuation.