These rolls are coated with aluminum oxide, which is the most common abrasive material and hard enough to sand steel and wood.

A thicker, heavier construction than standard rolls withstands tough sanding.

Sanding rolls with precision-shaped ceramic alumina abrade hard metals like stainless steel faster than standard ceramic alumina rolls because of their sharp, outwardly pointed grit.

The soft abrasive is good for fine hand-polishing of metal surfaces that require the smoothest finish possible after an abrasive sequence. Also known as crocus cloth.

Create smooth finishes on wood with these garnet sheets.

The soft abrasive is good for fine hand-polishing of soft nonferrous metals. Also known as crocus cloth.

These rolls resist deterioration when used wet or with grease, chemicals, cutting fluids, and other solvents that may be present when sanding.

The thick, abrasive-embedded nylon mesh construction flexes to compensate for uneven pressure as you sand, producing a consistent finish.

When you need to achieve a more consistent finish, choose nylon mesh sanding rolls over paper- or cloth-backed rolls.

Flexible enough to sand around curves and in corners, these sponges provide the comfort and control of a sanding block.

These sponges prevent debris from accumulating on the abrasive surface and keep operating temperatures low.

Evenly sand two surfaces at once.

Sized for tight spaces, these small pads sand flat and curved surfaces. They have a flexible foam layer that gives you more control over sanding pressure, creating finer and more consistent finishes.

These cut-to-length rolls resist deterioration when used wet or with grease, chemicals, cutting fluids, and other solvents that may be present when sanding. A layer of mesh lets sanding dust and debris escape during use, preventing material buildup on the abrasive surface.

The dental floss of abrasives, these cords slip into areas that other forms cannot. They're good for deburring and polishing small holes, narrow slots, keyways, and grooves.

The mesh in these sanding pads flexes to compensate for uneven pressure as you sand, producing a consistent finish.

Flexible enough to sand around curves and in corners, these sponges provide the comfort and control of a sanding block. They have a long-lasting diamond abrasive on one side.

Cut the length you need, then stick to your sanding tool. When it's time to change the sheet, peel it off.

Sanding rolls with precision-shaped ceramic alumina abrade hard metals like stainless steel faster than standard ceramic alumina rolls because of their sharp, outwardly pointed grit.

Create consistent finishes on stainless steel, titanium, steel, iron, and nickel.

Quickly attach, remove, and reuse.

Cut to convenient sizes and shapes, these fit most sheet sanders.

Peel and stick to your file handle. When it’s time to change the sheet, peel it off.

Dust and debris won't build up on the abrasive surface.

Quickly switch between different grits—these sanding sheets attach and detach from a compatible sanding block with hook and loop.

The mesh backing lets sanding dust and debris escape during use, preventing material build up on the abrasive surface.

The abrasive-embedded nylon mesh construction gives you more control over sanding pressure.

Get twice the life over standard nylon mesh cushioned discs—the flexible mesh in these discs is embedded with a premium form of aluminum oxide or ceramic alumina.

The nylon mesh on these discs is embedded with precision-shaped ceramic alumina, which cuts through hard metals like stainless steel faster than other forms of ceramic alumina because of its sharp, outwardly pointed grit.

The premium abrasive stays sharp longer.

The heavy duty construction provides more support than standard discs for heavy material removal.

These discs have a harder abrasive than standard flexible-edge quick-change discs.

A special fastener on the back of these discs allows you to easily swap one disc for another.

These discs have a long-lasting diamond abrasive.

Precision-shaped ceramic alumina discs abrade hard metals like stainless steel faster than standard ceramic alumina discs because of their sharp, outwardly pointed grit.

When you need to achieve a more consistent finish, choose nylon mesh sanding discs over paper- or cloth-backed discs.

Press onto a compatible sanding tool or backup pad; peel off to remove.

Coated with zirconia alumina to stay sharper longer.

The cushioned construction gives you more control over sanding pressure, creating finer and more consistent finishes.

The premium abrasive stays sharp longer.

The cushioned construction gives you more control over sanding pressure, creating finer and more consistent finishes.

The cushioned construction gives you more control over sanding pressure, creating finer and more consistent finishes.

For use with vacuum sanders, these discs have holes that allow dust to get sucked up before it can build up and dull the abrasive surface.

Holes allow dust removal when used with a vacuum sander.

Precision-shaped ceramic alumina discs abrade hard metals like stainless steel faster than standard ceramic alumina discs because of their sharp, outwardly pointed grit.

Quickly sand while capturing up to 97% of the dust generated.

For use with vacuum sanders, these discs have holes that allow dust to get sucked up before it can build up and dull the abrasive surface.

The nylon mesh on these discs is embedded with precision-shaped ceramic alumina, which cuts through hard metals like stainless steel faster than other forms of ceramic alumina because of its sharp, outwardly pointed grit.

These discs are abrasive-embedded cloth with a cushioned layer.

Quickly attach, remove, and reuse these discs with a compatible sanding tool or backup pad.

These discs have multiple layers of brick-shaped abrasive arranged in a pattern to create highly consistent finishes.

The cushioned construction gives you more control over sanding pressure, creating finer and more consistent finishes.

Holes allow dust removal when used with a vacuum sander.

The abrasive-embedded mesh construction gives you more control over sanding pressure, creating finer and more consistent finishes.

Nylon mesh is embedded with precision-shaped ceramic alumina, which cuts through hard metals like stainless steel faster than other forms of ceramic alumina because of its sharp, outwardly pointed grit.

Fit these discs over your tool's arbor.

Fit these discs over your tool's arbor to sand aluminum, soft metals, and nonmetals.

With more flaps than standard discs, these last 30-40% longer.

With more flaps than standard discs, these last 30-40% longer.

When you need to achieve a more consistent finish, choose nylon mesh sanding discs over paper- or cloth-backed discs.

Replace your sanding discs less often—the backing plate on these discs can be trimmed off as the abrasive flaps wear down, allowing you to use more of the disc.

Set at an angle and widely spaced, the overlapping abrasive flaps reach into corners.

Replace your sanding discs less often—the backing plate on these discs can be trimmed off as the abrasive flaps wear down, allowing you to use more of the disc.

A coating prevents dust and debris from building up on the abrasive surface.

The zirconia alumina grit on these discs continually fractures to produce new, sharp cutting edges that aggressively remove material from steel and wood.

Set at an angle and widely spaced, the flaps reach into corners.

The abrasive-embedded mesh construction gives you more control over sanding pressure, creating finer and more consistent finishes.

Sand both flat and irregularly shaped workpieces without gouging or leaving behind streaks.

Improve the strength of your concrete mix by eliminating trapped air.

Also known as mortar hoes, the blade on these tools has holes to allow concrete to pass through as you mix.

Once concrete begins to set up and surface water reabsorbs, finish with a trowel to compact the top layer for a smooth, hard surface.

Slide these tools along the perimeter of poured concrete slabs to create a rounded edge for a finished appearance that resists chipping.

Drag these brooms along hardening concrete to create a rough surface for traction in slippery environments.

Make removing form-board stakes easier.

Remove hardened flecks of mortar, dirt, and other debris.

Rub these tools along the mortar between bricks for a uniform, finished appearance.