Protect your face from low-level arc flashes when a full hood is not necessary.

All hard hats have a ratchet suspension that adjusts with an easy-turn knob.

Absorb sweat and stay cool by wearing these bandanas around your head or neck. They meet NFPA 70E and ASTM F1506 standards, so they’re safe to wear when sparks are flying. To keep you cool, they contain water-absorbing crystals. Run these bandanas under cold water for a few minutes, then the crystals will relieve heat through evaporation for up to 4 hours. They're made of a soft, breathable cotton and modacrylic blend that resists flames and protects against radiant heat.

Keep cool while staying shielded from flame and electrical hazards.

Shield your face and neck from flame and electrical hazards while working in the cold.

These face masks meet NFPA 70E standards for protection against electrical arc flashes for personal protection equipment (PPE) category 2. Check the PPE category and minimum arc rating provided for your workplace, and then select all required clothing and personal protective equipment to meet the minimum arc rating. Arc rating measures a garment’s ability to insulate the wearer from burns; the higher the arc rating, the greater the flame resistance. These hats are made of abrasion-resistant aramid/viscose blend fabric, which keeps you warm without accumulating moisture.

Withstand flash fire for up to 8 seconds—the clothes in these kits can protect you for twice as long as most flame-resistant clothing. Made of rayon/aramid, the coveralls and mask absorb moisture to keep you cool and comfortable.

The coveralls have a 10 ft. Kevlar strap, so nearby teammates can pull you to safety without putting themselves at risk if there’s a fire. The reflective stripes keep you easy to see where there's low visibility. The zipper closure on the front is covered by a hook-and-loop flap so it doesn't scrape equipment or get hot. The legs have zippers on the sides as well, so you can fit them over bulky boots. Tighten the hook and loop straps on the bottom of the pants to keep flames out. The sleeves have cuffs with thumb holes to keep the sleeves in place and prevent flames from sneaking in. When measuring chest size, measure around the fullest part of your chest. Take all measurements over any clothing you expect to wear under the coveralls.

These hoods meet NFPA 70E standards for protection against electrical arc flashes for personal protection equipment (PPE) category 4. Check the PPE category and minimum arc rating provided for your workplace, and then select all required clothing and personal protective equipment to meet the minimum arc rating. Arc rating measures a garment’s ability to insulate the wearer from burns; the higher the arc rating, the greater the flame resistance. Each hood has a hard hat with adjustable headgear and a face shield with an antifog coating.

Fans—Fans (sold separately) mount on your hood and pumps air inside using a fan motor. They operate on four AA batteries (not included).

Protect your head and neck from extreme heat. To fit your head, these hoods use an adjustable ratchet suspension. There's enough room inside to wear glasses, goggles, or a respirator.

Get up close to your welds with these goggles. Their lightweight, compact design lets you weld in tight spots or awkward positions. A flame-resistant hood shields your ears, head, and neck from sparks and spatter better than traditional welding helmets. For different protection needs, wear them over prescription glasses, under a hard hat, or without the hood. Use the external controls to adjust power and shade settings without removing these goggles.

As you begin to weld, two sensors detect the light and automatically darken the lens. Unlike traditional green welding lenses, these goggles use a true color lens to enhance clarity and color accuracy. They allow for a better look at your weld pool to increase weld quality and reduce eye strain.

Hold your hard hat securely on your head with these chin straps. Connect them to your hard hat and adjust the strap length with a slider for a snug fit.

Combine style and safety with these caps. Inside each cap is a protective insert for added defense against minor bumps and scrapes. If the insert cracks or you require a different style, such as one to fit over long hair, we offer replacement inserts.

Protect your head from electrical arc flashes. These face masks won’t melt or drip when exposed to intermittent flames. They meet NFPA 70E standards for personal protection equipment (PPE) category 2. Check the PPE category and minimum arc rating provided for your workplace, and then select all required clothing and personal protective equipment to meet the minimum arc rating. Arc rating measures a garment’s ability to insulate the wearer from burns; the higher the arc rating, the greater the flame resistance. Masks are soft, breathable, and washable.

These face masks are double-layered to protect your head from radiant heat, flames, and welding sparks. They are designed to meet NFPA 1971 standards for structural firefighting. Check the PPE category and minimum arc rating provided for your workplace, and then select all required clothing and personal protective equipment to meet the minimum arc rating. Arc rating measures a garment’s ability to insulate the wearer from burns; the higher the arc rating, the greater the flame resistance.

Clip these detectors to your hard hat to identify voltage and current from 360°. Without making physical contact, they flash light in the direction of the electrical threat and beep louder as you get closer to it. These lightweight detectors are comfortable to wear all day. They’re often used to identify live conductors, energized lines underground, and residual voltage.

Set the sensitivity level to determine when the detector alerts you. While the battery life varies depending on the number of alerts, a full charge can last up to five days. Recharge the battery with the included USB charging cable or a standard USB 2.0 Micro-B charger.

Protect your torso, hands, and eyes from sparks, spatter, and heat in welding areas. Each of these kits come with basic safety gear, common welding accessories, and a four-gallon bucket for easy gear transport. The included jacket protects against low radiant heat, with leather sleeves for added heat protection and cut resistance. Three pairs of gloves—one for TIG welding, one for stick welding, and one pair of standard leather work gloves—ensure you have the hand protection you need. These kits also come with two pairs of glasses: shaded ones to guard from harmful infrared light, plus a pair of standard safety glasses. When measuring chest size, measure around the fullest part of your chest. Take all measurements over any clothing you expect to wear under the coveralls.