Machine these clamps to match the contours of your workpiece and turn the screw to grip.

Install these clamps into a slot in your fixture to grip at the bottom of a workpiece edge, giving the cutting tool maximum access.

Set one of these clamps between two workpieces in a fixture and tighten the screw to push the clamp's sides out for a secure hold.

Secure a workpiece from the inside, leaving the outside clear for machining.

Tighten the spring-loaded socket head cap screw on these clamps to hold your workpiece from above.

Mount using the holes in the base.

Build these components into fixture plates, machine subplates, and tombstones for quick changes. The system clamps and locates at the same time for accurate positioning with repeatability of ±0.0005".

A nonreflective black oxide finish prevents glare that can interfere with machine vision systems.

Hold workpieces of slightly different thicknesses with one clamp. These clamps automatically adjust to compensate for imperfections or small inconsistencies on the material’s surface.

The handle locks in a horizontal position for more clearance above the clamp than standard hold-down toggle clamps.

Hold workpieces of different thicknesses without adjustment.

Push the lever to lock the handle and prevent accidental opening.

Push the lever to lock the handle and prevent accidental opening.

Weld these clamps to the side of an object or drill your own holes in the mounting plate and bolt into place.

The handle locks in a horizontal position for more clearance above the clamp.

Mount these clamps below a surface.

Suitable for production applications, these clamps have double the service life of other air-powered toggle clamps.

These clamps have mounting holes on the bottom.

The base fits into round or square holes on most workholding tables for clamping anywhere on the work surface.

The stepped end provides support and quick height adjustment when paired with a step block.

Eliminating the need for step blocks or other rear support, the pivoting rocker clamps workpieces of various thicknesses.

Get everything needed for basic workholding on a machine table.

Designed to provide more clearance above the nut than standard clamps, these have an offset shape. Also known as gooseneck clamps.

Position these clamps between two workpieces, vises, or fixtures and secure both to your machine table using T-slot nuts or bolts.

Keep setup clamps from falling out of position when they are unclamped—the spring holds them up for quick workpiece insertion and removal. Also known as spring lifters.

Unlike other setup clamps that grip the horizontal surface of a workpiece, these clamps have a pivoting ball in the tip to get a firm hold on angled parts.

The built-in T-slot nut on these side clamps lets you clamp a part to a machine table quickly. Their small footprint leaves more free space on your table than standard side clamps.

Smaller than standard setup clamps, these clamps leave more usable space on a machine table when mounting a vise.

Smaller than standard push/pull toggle clamps, these are often used for electronics and small fixturing applications.

Smaller than standard push toggle clamps, these are often used for electronics and small fixturing applications.

A highly durable construction with hardened steel pivot pins and bushings provides a long service life.

Moving parts are sealed to prevent dirt and dust from clogging the clamp.

Panel mount through a hole with the included nut, or drill and tap a hole to flush mount. A pushing or pulling motion holds workpieces from the side.

Secure these clamps to a rail or bar.

Use for repetitive clamping and in production environments or hard-to-reach locations.

Also known as press screws, mount these clamps through a drilled hole and turn the crank to move the jaw end of the screw in and out.

Each arm has a handle for turning the magnets on and off.

Hold and align up to three workpieces at 90° angles.

The clamping surfaces pivot individually to secure workpieces of different thicknesses at any angle from 5° to 180°.

Hold workpieces at a 90° angle.

Mount these versatile blocks to any flat surface for machine table-style T-slot clamping. They can also be used on a machine table to clamp parts at specific angles or add more total clamping points.