Turn heating equipment on or off in environments with flammable gases, combustible dust, and ignitable fibers, such as chemical plants, refineries, and grain elevators. The switch housing is UL listed for use in Class I, Divisions 1 and 2, Groups B, C, and D; Class II, Divisions 1 and 2, Groups E, F, and G; and Class III, Divisions 1 and 2 hazardous locations. It also meets NEMA 4X for use in washdown environments with splashing water, corrosive liquid, and dust. Switches have a probe on a cable for remote temperature readings. Set actuation points with the adjustment dial.

Switch with one actuation point has one SPDT (single pole, double throw) relay. The relay can be set to turn one circuit from off to on (normally open) or from on to off (normally closed). The probe has 1/2 NPT male threads for installation directly into tanks, pipelines, and other process components. It comes with a bushing that adapts the thread size to 3/4 NPT male.

Switch with two actuation points has two SPDT (single pole, double throw) relays. Each relay can be set to turn one circuit from off to on (normally open) or from on to off (normally closed).

Install the threaded probe directly into tanks, pipelines, and other process components to turn heating equipment on or off at a specified temperature. These switches have an adjustment dial to set the actuation point. All are SPDT (single pole, double throw). They can be set to turn one circuit from off to on (normally open) or from on to off (normally closed).

Since these switches don’t have a housing above the probe, they are often used in tight spaces and low-clearance areas. The threaded probe installs directly into tanks, pipelines, and other process components to turn heating equipment on or off at a specified temperature. Use the adjustment screw to set the actuation point. All switches are SPST (single pole, single throw) and control one circuit.

Normally open switches turn the circuit from off to on.

Normally closed switches turn the circuit from on to off.

For technical drawings and 3-D models, click on a part number.

A digital display makes it easy to monitor the temperature and control when these switches turn heating equipment on and off. They have an adjustable reset, so you can change the temperature range between when they activate and deactivate, commonly referred to as deadband and differential. Use the keypad to adjust the setpoint and reset point anywhere on the setpoint range. They produce an electronic signal that is often used to communicate with a programmable logic controller (PLC), so they're common in control and automation applications. Install them directly into tanks, pipelines, and other process components using their threaded probe.

These switches have a micro M12 plug, so you can quickly connect and disconnect them.

Rated IP65 and IP67, these switches protect against dust and water from washdowns and temporary submersion. They’re also UL listed, C-UL listed, and CE marked, so they meet U.S., Canadian, and European safety standards.

For technical drawings and 3-D models, click on a part number.

An adjustable reset lets you control the amount of temperature change, also known as deadband and differential, before these switches reset. Twist the rings to select the setpoint temperature and reset temperature anywhere within the setpoint range. When they reach the set temperature, they send an electronic signal to your programmable logic controller (PLC) to turn equipment on or off. Because they control two circuits, they turn one device from off to on (normally open) and another from on to off (normally closed). An LED illuminates to indicate they’re switching. These switches are often used in control and automation in hydraulics, pneumatics, air-conditioning, and refrigeration applications. Made of stainless steel, they resist corrosion and chemicals.

Install these switches directly into tanks, pipelines, and other process components using their threaded probe. They have a micro M12 plug connection and are compatible with micro M12 sockets, so you can quickly connect and disconnect them. After selecting your setpoint, tighten the locking ring to prevent unintentional changes.

IP rated, these switches seal out dust and water from temporary submersion. They also meet U.S., Canadian, and European safety standards.

To view switch wiring diagrams, select a part number and click Product Detail.

For technical drawings and 3-D models, click on a part number.