Thread Size Thread Size |
---|
Material Material |
---|
|
Installed Length Installed Length |
---|

|
Body Length Body Length |
---|
Flange Diameter Flange Diameter |
---|

For Minimum Material Thickness For MinimumMaterial Thickness |
---|
|
Drill Bit Size Drill Bit Size |
---|
Flange Thickness Flange Thickness |
---|

For Maximum Hole Diameter For Maximum Hole Diameter |
---|
|
Thread Spacing Thread Spacing |
---|
Tensile Strength Tensile Strength |
---|
|
|
DFARS (Defense Acquisition Regulations Supplement) DFARS (Defense AcquisitionRegulations Supplement) |
---|
RoHS (Restriction of Hazardous Substances) RoHS (Restriction ofHazardous Substances) |
---|
|
REACH (Registration, Evaluation, Authorization and Restriction of Chemicals) REACH (Registration,Evaluation, Authorization and Restriction of Chemicals) |
---|
|
Brass Flanged Screw-to-Expand Inserts for Plastic

Made from brass, these inserts are nonmagnetic, corrosion resistant, and electrically conductive. The flange provides a load-bearing surface and acts as an electrical contact. Press them into a drilled hole, then install a screw to expand the insert and drive the knurls into the surrounding plastic to keep it secure. Installed length includes the flange.
For technical drawings and 3-D models, click on a part number.
Flange | |||||||||
---|---|---|---|---|---|---|---|---|---|
Thread Size | Installed Lg. | Body Lg. | Dia. | Thick. | Drill Bit Size | For Max. Hole Dia. | Pkg. Qty. | Pkg. | |
Brass | |||||||||
2-56 | 0.156" | 0.136" | 0.187" | 0.02" | 1/8" | 1/8" | 50 | 000000000 | 000000 |
4-40 | 0.188" | 0.168" | 0.218" | 0.02" | 5/32" | 5/32" | 50 | 000000000 | 00000 |
4-40 | 1/4" | 0.228" | 0.218" | 0.02" | 5/32" | 5/32" | 25 | 000000000 | 0000 |
6-32 | 1/4" | 0.22" | 0.249" | 0.03" | 3/16" | 3/16" | 50 | 000000000 | 00000 |
8-32 | 0.281" | 0.246" | 0.28" | 0.03" | 7/32" | 7/32" | 25 | 000000000 | 0000 |
8-32 | 5/16" | 0.283" | 0.28" | 0.03" | 7/32" | 7/32" | 50 | 000000000 | 00000 |
10-32 | 0.313" | 0.27" | 0.312" | 0.04" | 1/4" | 1/4" | 25 | 000000000 | 0000 |
10-32 | 3/8" | 0.335" | 0.312" | 0.04" | 1/4" | 1/4" | 25 | 000000000 | 0000 |
1/4"-20 | 0.438" | 0.388" | 3/8" | 0.05" | 5/16" | 5/16" | 10 | 000000000 | 0000 |
1/4"-20 | 1/2" | 0.45" | 3/8" | 0.05" | 5/16" | 5/16" | 25 | 000000000 | 00000 |
5/16"-18 | 0.563" | 0.513" | 0.437" | 0.05" | 3/8" | 3/8" | 10 | 000000000 | 0000 |
3/8"-16 | 5/8" | 0.565" | 1/2" | 0.06" | 7/16" | 7/16" | 10 | 000000000 | 0000 |
Flange, mm | ||||||||||
---|---|---|---|---|---|---|---|---|---|---|
Thread Size | Thread Pitch, mm | Installed Lg., mm | Body Lg., mm | Dia. | Thick. | Drill Bit Size | For Max. Hole Dia. | Pkg. Qty. | Pkg. | |
Brass | ||||||||||
M3 | 0.5 | 4.8 | 4.29 | 5.5 | 0.51 | 4 mm | 4 mm | 50 | 000000000 | 00000 |
M3 | 0.5 | 6.3 | 5.8 | 5.5 | 0.51 | 4 mm | 4 mm | 25 | 000000000 | 0000 |
M4 | 0.7 | 7.1 | 6.25 | 7.1 | 0.81 | 5.6 mm | 5.6 mm | 25 | 000000000 | 0000 |
M4 | 0.7 | 8 | 7.19 | 7.1 | 0.81 | 5.6 mm | 5.6 mm | 50 | 000000000 | 0000 |
M5 | 0.8 | 9.5 | 8.51 | 7.9 | 0.99 | 6.4 mm | 6.4 mm | 25 | 000000000 | 0000 |
M6 | 1 | 12.7 | 11.45 | 9.5 | 1.25 | 8 mm | 8 mm | 25 | 000000000 | 0000 |
M8 | 1.25 | 14.3 | 13.05 | 11.1 | 1.25 | 9.5 mm | 9.5 mm | 10 | 000000000 | 0000 |
18-8 Stainless Steel Flanged Screw-to-Expand Inserts for Plastic

These 18-8 stainless steel inserts have good corrosion resistance and may be mildly magnetic. The flange provides a load-bearing surface. Press them into a drilled hole, then install a screw to expand the insert and drive the knurls into the surrounding plastic to keep it secure. Installed length includes the flange.
For technical drawings and 3-D models, click on a part number.
Flange | |||||||||
---|---|---|---|---|---|---|---|---|---|
Thread Size | Installed Lg. | Body Lg. | Dia. | Thick. | Drill Bit Size | For Max. Hole Dia. | Pkg. Qty. | Pkg. | |
18-8 Stainless Steel | |||||||||
2-56 | 5/32" | 0.136" | 0.187" | 0.02" | 1/8" | 1/8" | 10 | 000000000 | 00000 |
4-40 | 3/16" | 0.168" | 0.218" | 0.02" | 5/32" | 5/32" | 10 | 000000000 | 00000 |
6-32 | 1/4" | 0.23" | 0.249" | 0.02" | 3/16" | 3/16" | 10 | 000000000 | 00000 |
8-32 | 5/16" | 0.293" | 0.28" | 0.02" | 7/32" | 7/32" | 5 | 000000000 | 0000 |
10-32 | 3/8" | 0.345" | 0.312" | 0.03" | 1/4" | 1/4" | 5 | 000000000 | 0000 |
1/4"-20 | 1/2" | 0.47" | 3/8" | 0.03" | 5/16" | 5/16" | 5 | 000000000 | 00000 |
Flange, mm | ||||||||||
---|---|---|---|---|---|---|---|---|---|---|
Thread Size | Thread Pitch, mm | Installed Lg., mm | Body Lg., mm | Dia. | Thick. | Drill Bit Size | For Max. Hole Dia. | Pkg. Qty. | Pkg. | |
18-8 Stainless Steel | ||||||||||
M3 | 0.5 | 4.8 | 4.3 | 5.5 | 0.51 | 4 mm | 4 mm | 5 | 000000000 | 00000 |
M4 | 0.7 | 8 | 7.1 | 7.1 | 0.81 | 5.6 mm | 5.6 mm | 5 | 000000000 | 0000 |
M5 | 0.8 | 9.5 | 8.5 | 7.9 | 0.99 | 6.4 mm | 6.4 mm | 5 | 000000000 | 0000 |
M6 | 1 | 12.7 | 11.5 | 9.5 | 1.25 | 8 mm | 8 mm | 1 | 000000000 | 0000 |
Aluminum Flanged Screw-to-Expand Inserts for Plastic

These aluminum inserts are 70% lighter than brass inserts, electrically conductive, and nonmagnetic. They have good corrosion resistance, which is comparable to brass but not as good as stainless steel. The flange provides a load-bearing surface and acts as an electrical contact. Press them into a drilled hole, then install a screw to expand the insert and drive the knurls into the surrounding plastic to keep it secure. Installed length includes the flange.
For technical drawings and 3-D models, click on a part number.
Flange | |||||||||
---|---|---|---|---|---|---|---|---|---|
Thread Size | Installed Lg. | Body Lg. | Dia. | Thick. | Drill Bit Size | For Max. Hole Dia. | Pkg. Qty. | Pkg. | |
Aluminum | |||||||||
2-56 | 5/32" | 0.136" | 3/16" | 0.02" | 1/8" | 1/8" | 25 | 000000000 | 00000 |
4-40 | 0.186" | 0.166" | 7/32" | 0.02" | 5/32" | 5/32" | 25 | 000000000 | 0000 |
4-40 | 0.248" | 0.228" | 7/32" | 0.02" | 5/32" | 5/32" | 25 | 000000000 | 0000 |
6-32 | 0.252" | 0.222" | 1/4" | 0.03" | 3/16" | 3/16" | 25 | 000000000 | 0000 |
6-32 | 0.283" | 0.253" | 1/4" | 0.03" | 3/16" | 3/16" | 25 | 000000000 | 0000 |
8-32 | 0.286" | 0.246" | 9/32" | 0.04" | 7/32" | 7/32" | 25 | 000000000 | 00000 |
8-32 | 0.318" | 0.278" | 9/32" | 0.04" | 7/32" | 7/32" | 25 | 000000000 | 00000 |
10-24 | 3/8" | 0.345" | 5/16" | 0.03" | 1/4" | 1/4" | 10 | 000000000 | 0000 |
10-32 | 0.31" | 0.27" | 5/16" | 0.04" | 1/4" | 1/4" | 25 | 000000000 | 00000 |
10-32 | 0.372" | 0.332" | 5/16" | 0.04" | 1/4" | 1/4" | 25 | 000000000 | 00000 |
1/4"-20 | 0.438" | 0.388" | 3/8" | 0.05" | 5/16" | 5/16" | 20 | 000000000 | 00000 |
1/4"-20 | 1/2" | 0.45" | 3/8" | 0.05" | 5/16" | 5/16" | 20 | 000000000 | 00000 |
5/16"-18 | 0.563" | 0.533" | 7/16" | 0.03" | 3/8" | 3/8" | 10 | 000000000 | 00000 |
3/8"-16 | 5/8" | 0.595" | 1/2" | 0.03" | 7/16" | 0.438" | 10 | 000000000 | 00000 |
Flange, mm | ||||||||||
---|---|---|---|---|---|---|---|---|---|---|
Thread Size | Thread Pitch, mm | Installed Lg., mm | Body Lg., mm | Dia. | Thick. | Drill Bit Size | For Max. Hole Dia. | Pkg. Qty. | Pkg. | |
Aluminum | ||||||||||
M3 | 0.5 | 4.78 | 4.22 | 5.6 | 0.56 | 4 mm | 4 mm | 25 | 000000000 | 00000 |
M3 | 0.5 | 6.36 | 5.8 | 5.6 | 0.56 | 4 mm | 4 mm | 25 | 000000000 | 0000 |
M4 | 0.7 | 7.14 | 6.25 | 7.1 | 0.89 | 5.6 mm | 5.6 mm | 25 | 000000000 | 00000 |
M4 | 0.7 | 7.95 | 7.06 | 7.1 | 0.89 | 5.6 mm | 5.6 mm | 25 | 000000000 | 00000 |
M5 | 0.8 | 7.95 | 6.86 | 8 | 1.09 | 6.4 mm | 6.4 mm | 25 | 000000000 | 00000 |
M5 | 0.8 | 9.52 | 8.43 | 8 | 1.09 | 6.4 mm | 6.4 mm | 25 | 000000000 | 00000 |
M6 | 1 | 11.13 | 9.86 | 9.5 | 1.27 | 8 mm | 8 mm | 25 | 000000000 | 00000 |
M6 | 1 | 12.7 | 11.43 | 9.5 | 1.27 | 8 mm | 8 mm | 25 | 000000000 | 00000 |
M8 | 1.25 | 14.3 | 13.54 | 11.1 | 0.76 | 9.5 mm | 9.5 mm | 10 | 000000000 | 00000 |
M10 | 1.5 | 15.88 | 15.11 | 12.7 | 0.76 | 11.1 mm | 11.1 mm | 10 | 000000000 | 00000 |
Screw-to-Expand Inserts for Through Holes in Plastic

The flange keeps these inserts from pulling through a hole. Install on the underside of the material by pressing them into a drilled hole. Install a screw to expand the insert and drive the knurls into the surrounding plastic to keep it from pulling out. Made from brass, they’re nonmagnetic, corrosion resistant, and electrically conductive. Installed length includes the flange.
For technical drawings and 3-D models, click on a part number.
Flange | |||||||||
---|---|---|---|---|---|---|---|---|---|
Thread Size | Installed Lg. | Body Lg. | Dia. | Thick. | Drill Bit Size | For Max. Hole Dia. | Pkg. Qty. | Pkg. | |
Brass | |||||||||
2-56 | 5/32" | 0.136" | 0.187" | 0.02" | 1/8" | 1/8" | 25 | 000000000 | 00000 |
4-40 | 3/16" | 0.168" | 0.218" | 0.02" | 5/32" | 5/32" | 25 | 000000000 | 0000 |
6-32 | 1/4" | 0.224" | 0.249" | 0.03" | 3/16" | 3/16" | 25 | 000000000 | 00000 |
8-32 | 5/16" | 0.283" | 0.28" | 0.03" | 7/32" | 7/32" | 25 | 000000000 | 0000 |
10-32 | 3/8" | 0.336" | 0.312" | 0.04" | 1/4" | 1/4" | 25 | 000000000 | 00000 |
1/4"-20 | 1/2" | 0.45" | 3/8" | 0.05" | 5/16" | 5/16" | 25 | 000000000 | 00000 |
Flange, mm | ||||||||||
---|---|---|---|---|---|---|---|---|---|---|
Thread Size | Thread Pitch, mm | Installed Lg., mm | Body Lg., mm | Dia. | Thick. | Drill Bit Size | For Max. Hole Dia. | Pkg. Qty. | Pkg. | |
Brass | ||||||||||
M2 | 0.4 | 4 | 3.5 | 4.8 | 0.5 | 3.2 mm | 3.2 mm | 25 | 000000000 | 000000 |
M2.5 | 0.45 | 4.8 | 4.25 | 5.6 | 0.55 | 4 mm | 4 mm | 25 | 000000000 | 00000 |
M3 | 0.5 | 4.8 | 4.25 | 5.6 | 0.55 | 4 mm | 4 mm | 25 | 000000000 | 00000 |
M4 | 0.7 | 8 | 7.15 | 7.2 | 0.85 | 5.6 mm | 5.6 mm | 10 | 000000000 | 0000 |
M5 | 0.8 | 9.5 | 8.5 | 8 | 1 | 6.4 mm | 6.4 mm | 10 | 000000000 | 0000 |
M6 | 1 | 12.7 | 11.4 | 9.5 | 1.3 | 8 mm | 8 mm | 10 | 000000000 | 00000 |
M8 | 1.25 | 12.7 | 11.4 | 11 | 1.3 | 9.6 mm | 9.6 mm | 10 | 000000000 | 00000 |
Ultra-Fine-Threaded Inserts for Plastic

Use these inserts to install fine-threaded screws in existing holes. Made from brass, they’re corrosion resistant, electrically conductive, and nonmagnetic. Press them into a drilled hole.
For technical drawings and 3-D models, click on a part number.
Flange | ||||||||
---|---|---|---|---|---|---|---|---|
Thread Size | Installed Lg. | Body Lg. | Dia. | Thick. | Drill Bit Size | For Max. Hole Dia. | Each | |
Brass | ||||||||
6-80 | 1/4" | 0.225" | 1/4" | 0.03" | 7/32" | 7/32" | 000000000 | 00000 |
6-80 | 3/8" | 0.35" | 1/4" | 0.03" | 7/32" | 7/32" | 000000000 | 0000 |
3/16"-100 | 5/16" | 0.298" | 0.29" | 0.01" | 1/4" | 1/4" | 000000000 | 0000 |
3/16"-100 | 7/16" | 0.423" | 0.29" | 0.01" | 1/4" | 1/4" | 000000000 | 0000 |
3/16"-100 | 5/8" | 0.61" | 0.29" | 0.01" | 1/4" | 1/4" | 000000000 | 0000 |
3/16"-100 | 3/4" | 0.735" | 0.29" | 0.01" | 1/4" | 1/4" | 000000000 | 0000 |
1/4"-80 | 5/16" | 0.298" | 0.352" | 0.01" | 5/16" | 5/16" | 000000000 | 0000 |
1/4"-80 | 7/16" | 0.423" | 0.352" | 0.01" | 5/16" | 5/16" | 000000000 | 0000 |
1/4"-80 | 5/8" | 0.61" | 0.352" | 0.01" | 5/16" | 5/16" | 000000000 | 0000 |
1/4"-80 | 3/4" | 0.735" | 0.352" | 0.01" | 5/16" | 5/16" | 000000000 | 0000 |
1/4"-100 | 5/16" | 0.298" | 0.352" | 0.01" | 5/16" | 5/16" | 000000000 | 0000 |
1/4"-100 | 7/16" | 0.423" | 0.352" | 0.01" | 5/16" | 5/16" | 000000000 | 0000 |
1/4"-100 | 5/8" | 0.61" | 0.352" | 0.01" | 5/16" | 5/16" | 000000000 | 0000 |
1/4"-100 | 3/4" | 0.735" | 0.352" | 0.01" | 5/16" | 5/16" | 000000000 | 0000 |
Flange | |||||||||
---|---|---|---|---|---|---|---|---|---|
Thread Size | Thread Pitch, mm | Installed Lg., mm | Body Lg., mm | Dia., mm | Thick., mm | Drill Bit Size, mm | For Max. Hole Dia., mm | Each | |
Brass | |||||||||
M2.5 | 0.2 | 7 | 6.5 | 4.5 | 0.5 | 4 | 4 | 000000000 | 00000 |
M3 | 0.25 | 5 | 4.75 | 4.95 | 0.25 | 4.5 | 4.5 | 000000000 | 0000 |
M3 | 0.25 | 7 | 6.75 | 4.95 | 0.25 | 4.5 | 4.5 | 000000000 | 0000 |
M3 | 0.25 | 9 | 8.75 | 4.95 | 0.25 | 4.5 | 4.5 | 000000000 | 0000 |
M3 | 0.2 | 5 | 4.75 | 4.95 | 0.25 | 4.5 | 4.5 | 000000000 | 0000 |
M3 | 0.2 | 7 | 6.75 | 4.95 | 0.25 | 4.5 | 4.5 | 000000000 | 0000 |
M3 | 0.2 | 9 | 8.75 | 4.95 | 0.25 | 4.5 | 4.5 | 000000000 | 0000 |
Heat-Set Inserts for Plastic

Install these inserts into plastic parts to create a secure base for fasteners. Also known as Chevron and headed inserts, they are often used to strengthen mounting holes on brittle plastics, such as on 3D printed parts. Unlike plastic threads, which wear down with repeated use, these threads hold their shape over a long life. Press inserts into straight holes that have been drilled, printed, or molded into plastic parts, then heat them with a soldering tip to melt the surrounding plastic. As the plastic cools, it fuses to the sharp, diagonal ridges around the inserts, which withstand torque and prevent the inserts from being pulled out. The interior is fully threaded, so you can access the threads from both sides of a through-hole.
Flanged inserts have a wider end than standard inserts, which gives them a larger load-bearing surface and makes them harder to pull out. The flange also gives you a larger contact area for soldering. When threading into the flanged side, these inserts prevent over-tightening, which can cause brittle plastic to crack.
Made with lead, brass inserts are stronger than aluminum and other brass alloys but not as strong as stainless steel inserts. They have good corrosion resistance.
For technical drawings and 3-D models, click on a part number.
Inserts | ||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|
Flange | Soldering Installation Tips | Extraction Tips | ||||||||||
Thread Size | Installed Lg. | Thick. | Dia. | Drill Bit Size | For Max. Hole Dia. | Pkg. Qty. | Pkg. | Each | Each | |||
Brass | ||||||||||||
2-56 | 0.157" | 0.02" | 0.188" | 3.2 mm | 0.126" | 50 | 000000000 | 000000 | 000000000 | 000000 | 000000000 | 000000 |
4-40 | 0.226" | 0.02" | 0.218" | No. 22 | 0.157" | 50 | 000000000 | 00000 | 000000000 | 00000 | 000000000 | 00000 |
6-32 | 0.18" | 0.03" | 1/4" | No. 12 | 0.189" | 50 | 000000000 | 00000 | 000000000 | 00000 | 000000000 | 00000 |
6-32 | 0.281" | 0.03" | 1/4" | No. 12 | 0.189" | 50 | 000000000 | 00000 | 000000000 | 00000 | 000000000 | 00000 |
8-32 | 0.185" | 0.03" | 0.281" | No. 2 | 0.221" | 50 | 000000000 | 00000 | 000000000 | 00000 | 000000000 | 00000 |
8-32 | 1/4" | 0.03" | 0.281" | No. 2 | 0.221" | 50 | 000000000 | 00000 | 000000000 | 00000 | 000000000 | 00000 |
8-32 | 0.321" | 0.03" | 0.281" | No. 2 | 0.221" | 50 | 000000000 | 00000 | 000000000 | 00000 | 000000000 | 00000 |
10-24 | 1/4" | 0.04" | 0.312" | 6.4 mm | 0.252" | 50 | 000000000 | 00000 | 000000000 | 00000 | 000000000 | 00000 |
10-24 | 3/8" | 0.04" | 0.312" | 6.4 mm | 0.252" | 50 | 000000000 | 00000 | 000000000 | 00000 | 000000000 | 00000 |
10-32 | 0.225" | 0.04" | 0.312" | 6.4 mm | 0.252" | 50 | 000000000 | 00000 | 000000000 | 00000 | 000000000 | 00000 |
10-32 | 1/4" | 0.04" | 0.312" | 6.4 mm | 0.252" | 50 | 000000000 | 00000 | 000000000 | 00000 | 000000000 | 00000 |
10-32 | 3/8" | 0.04" | 0.312" | 6.4 mm | 0.252" | 50 | 000000000 | 00000 | 000000000 | 00000 | 000000000 | 00000 |
1/4"-20 | 0.3" | 0.05" | 3/8" | O | 0.316" | 25 | 000000000 | 00000 | 000000000 | 00000 | 000000000 | 00000 |
1/4"-20 | 1/2" | 0.05" | 3/8" | O | 0.316" | 25 | 000000000 | 00000 | 000000000 | 00000 | 000000000 | 00000 |
1/4"-28 | 1/2" | 0.05" | 3/8" | O | 0.316" | 25 | 000000000 | 00000 | 000000000 | 00000 | 000000000 | 00000 |
5/16"-18 | 1/2" | 0.05" | 0.437" | V | 0.377" | 10 | 000000000 | 0000 | 000000000 | 00000 | 000000000 | 00000 |
5/16"-24 | 1/2" | 0.05" | 0.437" | V | 0.377" | 10 | 000000000 | 0000 | 000000000 | 00000 | 000000000 | 00000 |
3/8"-16 | 1/2" | 0.07" | 0.55" | 15/32" | 0.469" | 10 | 000000000 | 00000 | 000000000 | 00000 | 000000000 | 00000 |
3/8"-24 | 1/2" | 0.07" | 0.55" | 15/32" | 0.469" | 10 | 000000000 | 00000 | 000000000 | 00000 | 000000 | 00 |
Soldering Iron, 40W | 00000000 | Each | 000000 |
Inserts | |||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Flange | Soldering Installation Tips | Extraction Tips | |||||||||||
Thread Size | Thread Pitch, mm | Installed Lg., mm | Thick., mm | Dia., mm | Drill Bit Size | For Max. Hole Dia., mm | Pkg. Qty. | Pkg. | Each | Each | |||
Brass | |||||||||||||
M2 | 0.4 | 4 | 0.46 | 4.8 | 3.2 mm | 3.2 | 50 | 000000000 | 000000 | 000000 | 00 | 000000 | 00 |
M3 | 0.5 | 5.7 | 0.53 | 5.5 | No. 22 | 4 | 50 | 000000000 | 00000 | 000000000 | 000000 | 000000000 | 000000 |
M3.5 | 0.6 | 7.1 | 0.69 | 6.4 | No. 12 | 4.8 | 50 | 000000000 | 00000 | 000000000 | 00000 | 000000000 | 00000 |
M4 | 0.7 | 4.7 | 0.84 | 7.1 | No. 2 | 5.6 | 50 | 000000000 | 00000 | 000000000 | 00000 | 000000000 | 00000 |
M4 | 0.7 | 8.2 | 0.84 | 7.1 | No. 2 | 5.6 | 50 | 000000000 | 00000 | 000000000 | 00000 | 000000000 | 00000 |
M5 | 0.8 | 9.5 | 1.02 | 7.9 | 6.4 mm | 6.4 | 50 | 000000000 | 00000 | 000000000 | 00000 | 000000000 | 00000 |
M6 | 1 | 7.6 | 1.27 | 9.5 | O | 8 | 50 | 000000000 | 00000 | 000000000 | 00000 | 000000000 | 00000 |
M6 | 1 | 12.7 | 1.27 | 9.5 | O | 8 | 25 | 000000000 | 00000 | 000000000 | 00000 | 000000000 | 00000 |
M8 | 1.25 | 12.7 | 1.27 | 11.1 | V | 9.6 | 10 | 000000000 | 0000 | 000000000 | 00000 | 000000000 | 00000 |
Soldering Iron, 40W | 00000000 | Each | 000000 |
Flanged Tapping Inserts for Softwood

The flange keeps these inserts from being pulled through a hole and provides a load-bearing surface. They have large threads that cut into softwood for a strong hold. Made of zinc alloy, they have mild corrosion resistance. Install using a hex driver or an installation bit and drill for faster installation. Installed length includes the flange.
For technical drawings and 3-D models, click on a part number.
Inserts | |||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Flange | Drive | Installation Bits | |||||||||||
Thread Size | Installed Lg. | Body Lg. | Dia. | Thick. | Drill Bit Size | For Max. Hole Dia. | Style | Size | Pkg. Qty. | Pkg. | Each | ||
Zinc Alloy | |||||||||||||
8-32 | 25/64" | 0.361" | 0.335" | 0.025" | 15/64" | 15/64" | Hex | 4 mm | 100 | 000000000 | 000000 | 000000000 | 000000 |
8-32 | 25/32" | 0.756" | 0.335" | 0.031" | 15/64" | 15/64" | Hex | 4 mm | 25 | 000000000 | 00000 | 000000000 | 00000 |
10-24 | 25/64" | 0.361" | 0.453" | 0.03" | 9/32" | 9/32" | Hex | 5 mm | 50 | 000000000 | 0000 | 000000000 | 00000 |
10-24 | 33/64" | 0.395" | 0.453" | 0.039" | 5/16" | 5/16" | Hex | 5 mm | 50 | 000000000 | 00000 | 000000000 | 00000 |
10-24 | 25/32" | 0.751" | 0.453" | 0.03" | 9/32" | 9/32" | Hex | 5 mm | 50 | 000000000 | 00000 | 000000000 | 00000 |
10-32 | 25/64" | 0.361" | 0.453" | 0.03" | 9/32" | 9/32" | Hex | 5 mm | 50 | 000000000 | 0000 | 000000000 | 00000 |
10-32 | 33/64" | 0.486" | 0.453" | 0.03" | 9/32" | 9/32" | Hex | 5 mm | 50 | 000000000 | 0000 | 000000000 | 00000 |
10-32 | 25/32" | 0.751" | 0.453" | 0.03" | 9/32" | 9/32" | Hex | 5 mm | 25 | 000000000 | 0000 | 000000000 | 00000 |
1/4"-20 | 25/64" | 0.354" | 0.492" | 0.04" | 23/64" | 23/64" | Hex | 6 mm | 50 | 000000000 | 00000 | 000000000 | 00000 |
1/4"-20 | 33/64" | 0.486" | 0.492" | 0.03" | 23/64" | 23/64" | Hex | 6 mm | 100 | 000000000 | 00000 | 000000000 | 00000 |
1/4"-20 | 25/32" | 0.741" | 0.492" | 0.04" | 23/64" | 23/64" | Hex | 6 mm | 50 | 000000000 | 00000 | 000000000 | 00000 |
1/4"-20 | 63/64" | 0.944" | 0.492" | 0.04" | 23/64" | 23/64" | Hex | 6 mm | 50 | 000000000 | 00000 | 000000000 | 00000 |
5/16"-18 | 33/64" | 0.486" | 0.571" | 0.03" | 7/16" | 7/16" | Hex | 8 mm | 50 | 000000000 | 00000 | 000000000 | 00000 |
5/16"-18 | 25/32" | 0.73" | 0.571" | 0.057" | 7/16" | 7/16" | Hex | 8 mm | 25 | 000000000 | 00000 | 000000000 | 00000 |
5/16"-18 | 63/64" | 0.954" | 0.571" | 0.03" | 7/16" | 7/16" | Hex | 8 mm | 25 | 000000000 | 00000 | 000000000 | 00000 |
3/8"-16 | 33/64" | 0.486" | 0.63" | 0.03" | 15/32" | 15/32" | Hex | 10 mm | 25 | 000000000 | 00000 | 000000000 | 00000 |
3/8"-16 | 63/64" | 0.944" | 5/8" | 0.04" | 15/32" | 15/32" | Hex | 10 mm | 25 | 000000000 | 00000 | 000000000 | 00000 |
Inserts | ||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Flange, mm | Drive | Installation Bits | ||||||||||||
Thread Size | Thread Pitch, mm | Installed Lg., mm | Body Lg., mm | Dia. | Thick. | Drill Bit Size | For Max. Hole Dia. | Style | Size | Pkg. Qty. | Pkg. | Each | ||
Zinc Alloy | ||||||||||||||
M6 | 1 | 13 | 12.365 | 12 | 0.635 | 9 mm | 9 mm | Hex | 6 mm | 50 | 000000000 | 00000 | 000000000 | 000000 |
M6 | 1 | 20 | 19.24 | 12 | 0.762 | 9 mm | 9 mm | Hex | 6 mm | 50 | 000000000 | 0000 | 000000000 | 00000 |
M8 | 1.25 | 13 | 11.98 | 15 | 1.016 | 11 mm | 11 mm | Hex | 8 mm | 25 | 000000000 | 0000 | 000000000 | 00000 |
M8 | 1.25 | 20 | 18.98 | 15 | 1.016 | 11 mm | 11 mm | Hex | 8 mm | 25 | 000000000 | 0000 | 000000000 | 00000 |
M10 | 1.5 | 13 | 12.2 | 16 | 0.8 | 12 mm | 12 mm | Hex | 10 mm | 25 | 000000000 | 0000 | 000000000 | 00000 |
M10 | 1.5 | 25 | 24 | 16 | 0.8 | 12 mm | 12 mm | Hex | 10 mm | 25 | 000000000 | 00000 | 000000000 | 00000 |
Flanged Barbed Inserts for Softwood

The flange keeps these inserts from being pulled through a hole and provides a load bearing surface. Barbs dig into softwood for a secure hold. Made of zinc alloy, they have mild corrosion resistance. Hammer them into a drilled hole to install. Installed length includes the flange.
For technical drawings and 3-D models, click on a part number.
Flange | |||||||||
---|---|---|---|---|---|---|---|---|---|
Thread Size | Installed Lg. | Body Lg. | Dia. | Thick. | Drill Bit Size | For Max. Hole Dia. | Pkg. Qty. | Pkg. | |
Zinc Alloy | |||||||||
8-32 | 0.453" | 0.394" | 0.413" | 0.059" | 1/4" | 1/4" | 50 | 000000000 | 000000 |
10-24 | 0.472" | 0.393" | 0.492" | 0.079" | 5/16" | 5/16" | 50 | 000000000 | 00000 |
1/4"-20 | 0.61" | 0.512" | 0.571" | 0.098" | 3/8" | 3/8" | 25 | 000000000 | 00000 |
5/16"-18 | 0.529" | 0.45" | 0.741" | 0.079" | 3/8" | 3/8" | 25 | 000000000 | 00000 |
5/16"-18 | 0.9" | 0.83" | 3/4" | 0.07" | 7/16" | 7/16" | 25 | 000000000 | 00000 |
Closed-End Flanged Barbed Inserts for Softwood

A closed end seals out elements and protects the threads on these inserts from debris. The flange keeps them from being pulled through a hole, and barbs dig into softwood for a secure hold. Made of zinc alloy, they are mildly corrosion resistant. Hammer them into a drilled hole to install. Installed length includes the flange.
For technical drawings and 3-D models, click on a part number.
Flange | |||||||||
---|---|---|---|---|---|---|---|---|---|
Thread Size | Installed Lg. | Body Lg. | Dia. | Thick. | Drill Bit Size | For Max. Hole Dia. | Pkg. Qty. | Pkg. | |
Zinc Alloy | |||||||||
8-32 | 0.443" | 0.394" | 0.433" | 0.049" | 1/4" | 1/4" | 50 | 000000000 | 000000 |
10-24 | 0.492" | 0.394" | 0.433" | 0.098" | 1/4" | 1/4" | 50 | 000000000 | 00000 |
10-32 | 0.492" | 0.394" | 0.433" | 0.098" | 1/4" | 1/4" | 50 | 000000000 | 00000 |
1/4"-20 | 0.62" | 0.41" | 0.669" | 0.21" | 11/32" | 11/32" | 25 | 000000000 | 00000 |
1/4"-20 | 0.694" | 0.611" | 0.669" | 0.083" | 11/32" | 11/32" | 25 | 000000000 | 00000 |
5/16"-18 | 0.687" | 0.602" | 0.669" | 0.085" | 11/32" | 11/32" | 25 | 000000000 | 00000 |
Knurled Inserts for Hardwood

Knurls hold these inserts in hardwood to prevent twisting. The flange keeps them from being pulled through a hole. Made of zinc-plated steel, they are mildly corrosion resistant. Hammer them into a drilled hole to install. Installed length includes the flange.
For technical drawings and 3-D models, click on a part number.
Flange | |||||||||
---|---|---|---|---|---|---|---|---|---|
Thread Size | Installed Lg. | Body Lg. | Dia. | Thick. | Drill Bit Size | For Max. Hole Dia. | Pkg. Qty. | Pkg. | |
Zinc-Plated Steel | |||||||||
8-32 | 0.315" | 0.276" | 0.315" | 0.039" | 7/32" | 7/32" | 25 | 000000000 | 000000 |
1/4"-20 | 0.303" | 0.244" | 0.473" | 0.059" | 21/64" | 21/64" | 10 | 000000000 | 00000 |
1/4"-20 | 0.473" | 0.414" | 0.473" | 0.059" | 21/64" | 21/64" | 10 | 000000000 | 0000 |
5/16"-18 | 0.473" | 0.394" | 0.59" | 0.079" | 13/32" | 13/32" | 10 | 000000000 | 00000 |