Flat Roller Bearings | McMaster-Carr

Filter by

System of Measurement

Shaft Diameter

Dynamic Thrust Load Capacity

Less than 2,000 lb.

2,000 lb. to 9,999 lb.

10,000 lb. to 19,999 lb.

20,000 lb. to 29,999 lb.

30,000 lb. or greater

Static Thrust Load Capacity

Less than 10,000 lb.

10,000 lb. to 19,999 lb.

20,000 lb. to 99,999 lb.

100,000 lb. to 199,999 lb.

200,000 lb. or greater

Cage Material

Bearing Seal Type

Material

Maximum Rotation Speed

Roller Bearing Type

DFARS Specialty Metals

REACH

RoHS

Export Control Classification Number (ECCN)

Performance

Maximum Temperature

Minimum Temperature

Rotation Speed

2,000 rpm to 2,999 rpm

3,000 rpm to 9,999 rpm

10,000 rpm to 19,999 rpm

20,000 rpm or greater

Specifications Met

Relative Thickness

Lubricant

185 Products

Needle-Roller Thrust Bearings


Bearings	Washers

Small but mighty, our thinnest rolling thrust bearings slot into tight spaces and spin at whirring speeds. Their long, slender rollers support thrust loads and reduce friction in everything from machine tool spindles to gearboxes.

A cage holds the rollers in place. You can install these bearings without washers between hardened, ground surfaces for the thinnest profile. If you’re working with unhardened, unground surfaces, you’ll need two washers for the rollers to run on. This three-piece design is easy to lubricate, but the oil will attract dust and grime since it’s exposed.

Steel—Strong and wear resistant. However, these bearings are best for dry environments since moisture will cause them to rust.

	Thrust Bearings										Thin Washers			Thick Washers
	For Shaft Dia.	OD	Thk.	Cage Material	Dynamic Thrust Load Cap., lb.	Max. Rotation Speed, rpm	Temp. Range, ° F	Specs. Met		Each	Thk.		Each	Thk.		Each
Steel



		1/4"	11/16"	5/64"	Steel	1,350	20,000	0 to 240	—	0000000	00000	0.032"	00000000	00000	0.095"	00000000	00000


		5/16"	3/4"	5/64"	Steel	1,150	24,000	0 to 240	—	0000000	0000	0.032"	00000000	0000	1/16"	00000000	0000
		3/8"	13/16"	5/64"	Steel	1,600	16,000	0 to 240	—	0000000	0000	0.032"	00000000	0000	0.063"	00000000	0000
		1/2"	15/16"	5/64"	Steel	1,900	13,000	0 to 240	—	0000000	0000	0.032"	0000000	0000	0.063"	00000000	0000
		9/16"	1"	5/64"	Steel	1,700	18,000	0 to 240	—	00000000	0000	1/32"	00000000	0000	1/16"	00000000	0000
		5/8"	1 1/8"	5/64"	Steel	2,150	11,000	0 to 240	—	0000000	0000	0.032"	0000000	0000	0.063"	00000000	0000
		3/4"	1 1/4"	5/64"	Steel	2,400	9,500	0 to 240	—	0000000	0000	0.032"	0000000	0000	0.126"	0000000	0000
		7/8"	1 7/16"	5/64"	Steel	2,900	8,000	0 to 240	—	0000000	0000	0.032"	0000000	0000	0.126"	0000000	0000
		7/8"	1 11/16"	5/64"	Steel	4,400	7,500	0 to 240	—	0000000	0000	0.032"	0000000	0000	—	———	0
		1"	1 9/16"	5/64"	Steel	3,150	7,500	0 to 240	—	0000000	0000	0.032"	0000000	0000	0.126"	0000000	0000
		1 1/16"	1 5/8"	5/64"	Steel	3,400	8,400	0 to 240	—	00000000	0000	—	———	0	—	———	0


		1 1/8"	1 3/4"	5/64"	Steel	3,850	6,500	0 to 240	—	0000000	0000	0.032"	0000000	0000	0.126"	0000000	0000
		1 1/4"	1 15/16"	5/64"	Steel	4,500	6,000	0 to 240	—	0000000	0000	0.032"	0000000	0000	0.126"	0000000	0000
		1 3/8"	2 1/16"	5/64"	Steel	4,600	5,500	0 to 240	—	0000000	0000	0.032"	0000000	0000	0.126"	0000000	00000
		1 1/2"	2 3/16"	5/64"	Steel	4,850	5,000	0 to 240	—	0000000	0000	0.032"	0000000	0000	0.126"	0000000	0000
		1 3/4"	2 1/2"	5/64"	Steel	5,600	4,400	0 to 240	—	0000000	0000	0.032"	0000000	0000	0.126"	00000000	0000
		2"	2 3/4"	5/64"	Steel	5,800	4,000	0 to 240	—	0000000	0000	0.032"	0000000	0000	0.126"	0000000	00000
		2 1/8"	2 7/8"	5/64"	Steel	5,450	5,800	0 to 240	—	00000000	0000	1/32"	00000000	0000	1/16"	00000000	0000
		2 1/4"	3"	5/64"	Steel	5,550	5,600	0 to 240	—	0000000	00000	0.032"	00000000	0000	0.126"	00000000	0000
		2 1/2"	3 1/4"	5/64"	Steel	6,200	3,300	0 to 240	—	0000000	00000	0.032"	00000000	0000	—	———	0
		2 3/4"	3 5/8"	1/8"	Steel	10,700	4,600	0 to 240	—	00000000	00000	1/32"	00000000	0000	1/16"	00000000	00000


		3"	3 3/4"	5/64"	Steel	6,600	2,800	0 to 240	—	0000000	00000	0.032"	00000000	00000	0.126"	00000000	00000
		3 1/4"	4 1/8"	1/8"	Steel	11,600	4,000	0 to 240	—	00000000	00000	1/32"	00000000	00000	1/8"	00000000	00000
		3 3/4"	4 5/8"	1/8"	Steel	12,600	3,500	0 to 240	—	00000000	00000	1/32"	00000000	00000	1/16"	00000000	00000
		4 1/8"	5 1/16"	1/8"	Steel	14,300	3,200	0 to 240	—	00000000	000000	1/32"	00000000	00000	3/32"	00000000	00000
		4 mm	14 mm	2 mm	Nylon	1,000	21,000	0 to 240	DIN 5405-2	000000	0000	1 mm	00000000	0000	—	———	0
		5 mm	15 mm	2 mm	Nylon	1,050	21,000	0 to 240	DIN 5405-2	000000	0000	1 mm	00000000	0000	—	———	0
		6 mm	19 mm	2 mm	Nylon	1,500	19,000	0 to 240	DIN 5405-2	0000000	0000	1 mm	00000000	0000	2.75 mm	00000000	00000
		8 mm	21 mm	2 mm	Nylon	1,750	18,000	0 to 240	DIN 5405-2	000000	0000	1 mm	00000000	0000	2.75 mm	00000000	00000
		10 mm	24 mm	2 mm	Steel	2,050	17,000	0 to 240	DIN 5405-2	0000000	0000	1 mm	0000000	0000	2.75 mm	0000000	00000
		12 mm	26 mm	2 mm	Steel	2,200	15,000	0 to 240	DIN 5405-2	0000000	0000	1 mm	0000000	0000	2.75 mm	0000000	0000


		15 mm	28 mm	2 mm	Steel	2,550	13,000	0 to 240	DIN 5405-2	0000000	0000	1 mm	0000000	0000	2.75 mm	0000000	0000
		17 mm	30 mm	2 mm	Steel	2,700	12,000	0 to 240	DIN 5405-2	0000000	0000	1 mm	0000000	0000	2.75 mm	0000000	00000
		18 mm	31 mm	2 mm	Steel	2,140	10,000	0 to 240	—	0000000	00000	1 mm	0000000	0000	—	———	0
		20 mm	35 mm	2 mm	Steel	2,950	10,000	0 to 240	DIN 5405-2	0000000	0000	1 mm	0000000	0000	2.75 mm	0000000	00000
		25 mm	42 mm	2 mm	Steel	3,300	8,500	0 to 240	DIN 5405-2	0000000	0000	1 mm	0000000	0000	3 mm	0000000	00000
		30 mm	47 mm	2 mm	Steel	3,650	7,500	0 to 240	DIN 5405-2	0000000	0000	1 mm	0000000	0000	3 mm	0000000	00000
		35 mm	52 mm	2 mm	Steel	4,000	6,500	0 to 240	DIN 5405-2	0000000	0000	1 mm	0000000	0000	3.5 mm	0000000	00000
		40 mm	60 mm	3 mm	Steel	6,300	6,000	0 to 240	DIN 5405-2	000000	00000	1 mm	00000000	0000	3.5 mm	00000000	00000
		45 mm	65 mm	3 mm	Steel	6,700	5,000	0 to 240	DIN 5405-2	0000000	00000	1 mm	0000000	0000	4 mm	0000000	00000
		50 mm	70 mm	3 mm	Steel	7,200	4,800	0 to 240	DIN 5405-2	0000000	00000	1 mm	0000000	0000	4 mm	0000000	00000


		55 mm	78 mm	3 mm	Steel	8,500	4,300	0 to 240	DIN 5405-2	0000000	00000	1 mm	0000000	0000	5 mm	0000000	00000
		60 mm	85 mm	3 mm	Steel	10,000	4,000	0 to 240	DIN 5405-2	000000	00000	1 mm	00000000	0000	4.75 mm	00000000	00000
		65 mm	90 mm	3 mm	Steel	10,400	3,700	0 to 240	DIN 5405-2	0000000	00000	1 mm	00000000	0000	5.25 mm	00000000	00000
		70 mm	95 mm	4 mm	Steel	12,100	3,500	0 to 240	DIN 5405-2	000000	00000	1 mm	00000000	0000	5.25 mm	00000000	00000
		75 mm	100 mm	4 mm	Steel	12,400	3,300	0 to 240	DIN 5405-2	000000	00000	1 mm	00000000	00000	5.75 mm	00000000	00000
		80 mm	105 mm	4 mm	Steel	12,500	3,100	0 to 240	DIN 5405-2	000000	00000	1 mm	00000000	00000	5.75 mm	00000000	00000
		85 mm	110 mm	4 mm	Steel	13,000	2,950	0 to 240	DIN 5405-3, ISO 303	00000000	00000	1 mm	00000000	00000	5.75 mm	00000000	00000
		90 mm	120 mm	4 mm	Steel	16,400	2,700	0 to 240	DIN 5405-3, ISO 303	00000000	00000	1 mm	00000000	00000	—	———	0
		100 mm	135 mm	4 mm	Steel	20,400	2,420	0 to 240	DIN 5405-3, ISO 303	00000000	00000	1 mm	00000000	00000	—	———	0
		110 mm	145 mm	4 mm	Steel	21,800	2,230	0 to 240	DIN 5405-3, ISO 303	00000000	000000	1 mm	00000000	00000	—	———	0

120 mm	155 mm	4 mm	Steel	22,900	2,070	0 to 240	DIN 5405-3, ISO 303	00000000	000000	1 mm	00000000	00000	—	———	0
130 mm	170 mm	5 mm	Steel	29,900	1,900	0 to 240	DIN 5405-3, ISO 303	00000000	000000	1 mm	00000000	00000	—	———	0
140 mm	180 mm	5 mm	Steel	31,000	1,780	0 to 240	DIN 5405-3, ISO 303	00000000	000000	1 mm	00000000	00000	—	———	0
150 mm	190 mm	5 mm	Steel	32,100	1,680	0 to 240	DIN 5405-3, ISO 303	00000000	000000	1 mm	00000000	000000	—	———	0
160 mm	200 mm	5 mm	Steel	33,200	1,590	0 to 240	DIN 5405-3, ISO 303	00000000	000000	1 mm	00000000	000000	—	———	0

Washers for Needle-Roller Thrust Bearings

Adapt needle-roller thrust bearings to use on unhardened, unground surfaces.

For Shaft Dia.	OD	Thk.	Washer Material	Specs. Met		Each
1/4"	11/16"	0.032"	Steel	—	00000000	00000
1/4"	11/16"	0.095"	Steel	—	00000000	0000
5/16"	3/4"	0.032"	Steel	—	00000000	0000
5/16"	3/4"	1/16"	Steel	—	00000000	0000
3/8"	13/16"	0.032"	Steel	—	00000000	0000
3/8"	13/16"	0.063"	Steel	—	00000000	0000
1/2"	15/16"	0.032"	Steel	—	0000000	0000
1/2"	15/16"	0.063"	Steel	—	00000000	0000
1/2"	15/16"	0.095"	Steel	—	00000000	0000
9/16"	1"	1/32"	Steel	—	00000000	0000
9/16"	1"	1/16"	Steel	—	00000000	0000
5/8"	1 1/8"	0.032"	Steel	—	0000000	0000
5/8"	1 1/8"	0.063"	Steel	—	00000000	0000
5/8"	1 1/8"	0.095"	Steel	—	00000000	0000
3/4"	1 1/4"	0.032"	Steel	—	0000000	0000
3/4"	1 1/4"	0.126"	Steel	—	0000000	0000
7/8"	1 7/16"	0.032"	Steel	—	0000000	0000
7/8"	1 7/16"	0.126"	Steel	—	0000000	0000
7/8"	1 11/16"	0.032"	Steel	—	0000000	0000
1"	1 9/16"	0.032"	Steel	—	0000000	0000
1"	1 9/16"	0.126"	Steel	—	0000000	0000
1 1/8"	1 3/4"	0.032"	Steel	—	0000000	0000
1 1/8"	1 3/4"	0.126"	Steel	—	0000000	0000
1 1/4"	1 15/16"	0.032"	Steel	—	0000000	0000
1 1/4"	1 15/16"	0.126"	Steel	—	0000000	0000
1 3/8"	2 1/16"	0.032"	Steel	—	0000000	0000
1 3/8"	2 1/16"	0.126"	Steel	—	0000000	00000
1 1/2"	2 3/16"	0.032"	Steel	—	0000000	0000
1 1/2"	2 3/16"	0.126"	Steel	—	0000000	0000
1 3/4"	2 1/2"	0.032"	Steel	—	0000000	0000
1 3/4"	2 1/2"	0.063"	Steel	—	00000000	0000
1 3/4"	2 1/2"	0.126"	Steel	—	00000000	0000
2"	2 3/4"	0.032"	Steel	—	0000000	0000
2"	2 3/4"	0.126"	Steel	—	0000000	00000
2 1/8"	2 7/8"	1/32"	Steel	—	00000000	0000
2 1/8"	2 7/8"	1/16"	Steel	—	00000000	0000
2 1/4"	3"	1/32"	Steel	—	00000000	0000
2 1/4"	3"	0.032"	Steel	—	00000000	0000
2 1/4"	3"	0.126"	Steel	—	00000000	0000
2 1/4"	3 1/8"	3/32"	Steel	—	00000000	00000
2 1/2"	3 1/4"	0.032"	Steel	—	00000000	0000
2 3/4"	3 5/8"	1/32"	Steel	—	00000000	0000
2 3/4"	3 5/8"	1/16"	Steel	—	00000000	00000
3"	3 3/4"	0.032"	Steel	—	00000000	00000
3"	3 3/4"	0.126"	Steel	—	00000000	00000
3 1/4"	4 1/8"	1/32"	Steel	—	00000000	00000
3 1/4"	4 1/8"	1/8"	Steel	—	00000000	00000
3 3/4"	4 5/8"	1/32"	Steel	—	00000000	00000
3 3/4"	4 5/8"	1/16"	Steel	—	00000000	00000
4 1/8"	5 1/16"	1/32"	Steel	—	00000000	00000
4 1/8"	5 1/16"	3/32"	Steel	—	00000000	00000
4 mm	14 mm	1 mm	Steel	DIN 5405-3, ISO 303	00000000	0000
5 mm	15 mm	1 mm	Steel	DIN 5405-3, ISO 303	00000000	0000
6 mm	19 mm	1 mm	Steel	DIN 5405-3, ISO 303	00000000	0000
6 mm	19 mm	2.75 mm	Steel	—	00000000	00000
8 mm	21 mm	1 mm	Steel	DIN 5405-3, ISO 303	00000000	0000
8 mm	21 mm	2.75 mm	Steel	—	00000000	00000
10 mm	24 mm	1 mm	Steel	DIN 5405-3, ISO 303	0000000	0000
10 mm	24 mm	2.75 mm	Steel	—	0000000	00000
12 mm	26 mm	1 mm	Steel	DIN 5405-3, ISO 303	0000000	0000
12 mm	26 mm	2.75 mm	Steel	—	0000000	0000
15 mm	28 mm	1 mm	Steel	DIN 5405-3, ISO 303	0000000	0000
15 mm	28 mm	2.75 mm	Steel	—	0000000	0000
17 mm	30 mm	1 mm	Steel	DIN 5405-3, ISO 303	0000000	0000
17 mm	30 mm	2.75 mm	Steel	—	0000000	00000
18 mm	31 mm	1 mm	Steel	—	0000000	0000
20 mm	35 mm	1 mm	Steel	DIN 5405-3, ISO 303	0000000	0000
20 mm	35 mm	2.75 mm	Steel	—	0000000	00000
25 mm	42 mm	1 mm	Steel	DIN 5405-3, ISO 303	0000000	0000
25 mm	42 mm	3 mm	Steel	—	0000000	00000
30 mm	47 mm	1 mm	Steel	DIN 5405-3, ISO 303	0000000	0000
30 mm	47 mm	3 mm	Steel	—	0000000	00000
35 mm	52 mm	1 mm	Steel	DIN 5405-3, ISO 303	0000000	0000
35 mm	52 mm	3.5 mm	Steel	—	0000000	00000
40 mm	60 mm	1 mm	Steel	DIN 5405-3, ISO 303	00000000	0000
40 mm	60 mm	3.5 mm	Steel	—	00000000	00000
45 mm	65 mm	1 mm	Steel	DIN 5405-3, ISO 303	0000000	0000
45 mm	65 mm	4 mm	Steel	—	0000000	00000
50 mm	70 mm	1 mm	Steel	DIN 5405-3, ISO 303	0000000	0000
50 mm	70 mm	4 mm	Steel	—	0000000	00000
55 mm	78 mm	1 mm	Steel	DIN 5405-3, ISO 303	0000000	0000
55 mm	78 mm	5 mm	Steel	—	0000000	00000
60 mm	85 mm	1 mm	Steel	DIN 5405-3, ISO 303	00000000	0000
60 mm	85 mm	4.75 mm	Steel	—	00000000	00000
65 mm	90 mm	1 mm	Steel	DIN 5405-3, ISO 303	00000000	0000
65 mm	90 mm	5.25 mm	Steel	—	00000000	00000
70 mm	95 mm	1 mm	Steel	DIN 5405-3, ISO 303	00000000	0000
70 mm	95 mm	5.25 mm	Steel	—	00000000	00000
75 mm	100 mm	1 mm	Steel	DIN 5405-3, ISO 303	00000000	00000
75 mm	100 mm	5.75 mm	Steel	—	00000000	00000
80 mm	105 mm	1 mm	Steel	DIN 5405-3, ISO 303	00000000	00000
80 mm	105 mm	5.75 mm	Steel	—	00000000	00000
85 mm	110 mm	1 mm	Steel	DIN 5405-3, ISO 303	00000000	00000
85 mm	110 mm	5.75 mm	Steel	DIN 5405-3, ISO 303	00000000	00000
90 mm	120 mm	1 mm	Steel	DIN 5405-3, ISO 303	00000000	00000
100 mm	135 mm	1 mm	Steel	DIN 5405-3, ISO 303	00000000	00000
110 mm	145 mm	1 mm	Steel	DIN 5405-3, ISO 303	00000000	00000
120 mm	155 mm	1 mm	Steel	DIN 5405-3, ISO 303	00000000	00000
130 mm	170 mm	1 mm	Steel	DIN 5405-3, ISO 303	00000000	00000
140 mm	180 mm	1 mm	Steel	DIN 5405-3, ISO 303	00000000	00000
150 mm	190 mm	1 mm	Steel	DIN 5405-3, ISO 303	00000000	000000
160 mm	200 mm	1 mm	Steel	DIN 5405-3, ISO 303	00000000	000000

Extreme-Load Tapered-Roller Thrust Bearings

With thick, tapered rollers, these thrust bearings are the strongest we offer. The rollers spin inside a raceway instead of a cage, so there’s room for more rollers to support higher loads than three-piece designs. You’ll often find them on crane hooks and kingpins that connect semi-trailers to semi-tractors. However, they rotate at a fraction of the speed of other roller thrust bearings.

Since they come as one piece, you don’t need to assemble cages and washers to install. An outer band holds the rollers inside the raceway, keeping lubricant in and dirt out.

Steel—Strong and wear resistant. However, these bearings are best for dry environments since moisture will cause them to rust.

Open—With no rubber seal to block airflow, these bearings dissipate heat quickly, extending the life of the lubricant and reducing friction over time.

Sealed—The best choice for dirty environments. In addition to a band, these bearings also have a rubber seal to block dust from creeping in and wearing down the rollers. However, they retain the most heat since air can’t flow through.

	Dynamic Thrust Load Cap., lb.	Max. Rotation Speed, rpm	Temp. Range, ° F		Each
Steel







	Open

	1 1/4"	2.198"	0.625"	12,000	10	0 to 150	00000000	000000


	1 1/4"	2.635"	0.7658"	18,300	10	0 to 150	00000000	00000
	1 3/8"	2.323"	0.656"	14,500	10	0 to 150	00000000	00000
	1 1/2"	2.604"	0.765"	20,300	10	0 to 150	00000000	00000
	1 5/8"	2.869"	0.8438"	20,500	10	0 to 150	00000000	00000
	1 13/16"	3.276"	0.9375"	28,400	10	0 to 150	00000000	00000
	2"	2.948"	0.625"	13,300	10	0 to 150	00000000	000000
	2 1/16"	3.682"	1.062"	37,500	10	0 to 150	00000000	000000




			Sealed

			1 1/4"	2.29"	0.677"	12,000	10	0 to 150	00000000	00000


			1 3/8"	2.398"	0.656"	14,500	10	0 to 150	00000000	00000
			1 1/2"	2.705"	0.815"	20,300	10	0 to 150	00000000	00000
			1 5/8"	2.98"	0.8438"	20,500	10	0 to 150	00000000	00000
			1 13/16"	3.455"	0.99"	28,400	10	0 to 150	00000000	00000
			2 1/16"	3.823"	1.121"	37,500	10	0 to 150	00000000	000000

High-Load Cylindrical-Roller Thrust Bearings

Thick, pop-can-shaped rollers balance strength and speed. These bearings reduce friction and support heavier loads than ball or needle-roller thrust bearings.

They come as three separate pieces—one cage and two washers. The cage holds the rollers in place, while the washers create a surface for the rollers to run on. This design is easy to lubricate, but the oil will attract dust and grime since it’s exposed.

Steel—Strong and wear resistant. However, these bearings are best for dry environments since moisture will cause them to rust.

	OD, mm	Thk., mm	Cage Material	Dynamic Thrust Load Cap., lb.	Max. Rotation Speed, rpm	Temp. Range, ° F	Includes		Each
Steel



	15	28	9	Nylon	3,200	13,400	-25 to 245	Two Washers	0000000	0000000


	17	30	9	Nylon	3,550	12,300	-25 to 245	Two Washers	0000000	000000
	20	35	10	Nylon	5,550	10,500	-25 to 245	Two Washers	0000000	000000
	25	42	11	Nylon	7,400	8,600	-25 to 245	Two Washers	0000000	000000
	30	47	11	Nylon	7,950	7,500	-25 to 245	Two Washers	0000000	000000
	35	52	12	Nylon	8,750	6,600	-25 to 245	Two Washers	0000000	000000
	40	60	13	Nylon	12,550	5,900	-25 to 245	Two Washers	0000000	000000
	45	65	14	Nylon	13,250	5,200	-25 to 245	Two Washers	0000000	000000
	50	70	14	Nylon	13,900	4,900	-25 to 245	Two Washers	0000000	000000
	55	78	16	Nylon	20,200	4,350	-25 to 245	Two Washers	0000000	000000
	60	85	17	Nylon	23,150	3,950	-25 to 245	Two Washers	0000000	000000


	65	90	18	Nylon	24,050	3,700	-25 to 245	Two Washers	0000000	000000
	70	95	18	Nylon	24,950	3,500	-25 to 245	Two Washers	0000000	000000