The flanged ends on these expansion joints rotate for easy bolt hole alignment during installation.

The PTFE body on these expansion joints has a super-smooth surface that stands up to corrosive chemicals.

Slip these joints over your pipe ends and tighten the band clamps for a secure hold.

These joints weld to unthreaded pipe or another butt-weld fitting for a leak-resistant permanent connection.

Connect two pipes that are up to 100 feet apart—cut the connector to the length you need and attach a clamp to each end.

Also know as pump connectors, hose is sized to specific lengths for attaching to pumps.

Run natural and LP gas through this heavy duty hose that's flexible enough for routing through walls and ceilings.

These short lengths of hose have a collar on each end to prevent the clamp from slipping off.

If you need frequent access to your line, these connectors join with a twist. They are also known as J-lock connectors.

These fittings seal out liquids when connecting liquid-tight flexible metal conduit to a knockout in an outlet box or enclosure.

Join pieces of conduit.

Join pieces of conduit.

Also known as antishort bushings, these grommets slide into the ends of conduit and armored cable to protect wire and cable from sharp edges.

Join pieces of conduit.

Preventing wear and cracks, these grommets shield the sections of your conduit that rub and bang against nearby components.

Join pieces of conduit.

Hold flexible plastic conduit in place along walls and machines.

Transition between conduit sizes and types.

One end twists into a piece of conduit for a quick connection; the other end attaches to a knockout in an outlet box or enclosure.

Designed to grip evenly around your shaft, these couplings provide more holding power than set screw couplings without marring the shaft.

Also called double-loop couplings, these have a flexible center that reduces vibration and compensates for high parallel and angular shaft misalignment.

Each hub includes a set screw, which bites into your shaft to hold the coupling in place.

Specially designed ridges allow these bellows couplings to compensate for more misalignment than other precision couplings—useful for low-torque, high-precision applications such as instrumentation and motion control.

An acetal plastic spacer at the center of these couplings insulates bearings, encoders, and other shaft components from stray electric current. Use them with servomotors, which sometimes generate current that travels down the shaft and can damage circuit boards, interfere with readings, and cause wear on bearing raceways.

Designed to grip evenly around your shaft, these couplings provide more holding power than set screw couplings without marring the shaft.

Customize the bore of these flexible couplings to align uncommon shaft sizes as well as shafts that have become undersized from wear or oversized from coatings.

Designed for use in food-processing applications, where a fraying spider could contaminate a batch, these couplings have a metal-detector-grade rubber spider. Small pieces of metal inside the rubber will set off a metal detector, alerting you to the problem.

Also known as Schmidt couplings, these handle higher angular misalignment than other three-piece couplings. Good for applications with varying shaft misalignment, they're commonly used with conveyor rollers and roller feeds in printing and packaging machines.

A flexible tire on these couplings safeguards components on your shafts by reducing vibration and shock.

Use these gear-shaped couplings for high-speed and high-torque applications.

With a rugged roller-chain design, these couplings provide excellent torque and angular misalignment capacities.

Customize the bore size of these joints to fit your shaft. Each end has a small centered starter hole that makes drilling easy.

These pin-and-block style U-joints work at lower speeds but transmit greater torque than needle-bearing joints.

These U-joints handle at least 11,000 in.-lbs. of torque.

Stainless steel hubs allow these U-joints to handle harsh environments.

Made of stainless steel, these U-joints offer excellent corrosion resistance.

These U-joints are made of steel.

Stainless steel U-joints are more corrosion resistant than steel U-joints.

Made of stainless steel, these U-joints offer excellent corrosion resistance. They also meet MIL-U-20625A Class A.

These steel U-joints meet MIL-U-20625A Class A and have hardened yoke ears for added strength and durability.

These stainless steel shafts are more corrosion resistant than steel models.

If they exceed maximum torque, these couplings disengage, sound an alarm, and then automatically re-engage once the overtorque condition is eliminated.