For Drive Style For Drive Style |
|---|
 |  |  |
| Phillips | Slotted | Torx |
 |  |  |
| External Hex | Square | Pozidriv® |
 |  | |
| Tamper- Resistant Hex | Tamper- Resistant Torx |
Size Size |
|---|
Individual/Set Individual/Set |
|---|
|
Overall Length Overall Length |
|---|
|
|
|
For Bit Shank Type For Bit Shank Type |
|---|
 | Hex |
 | Hex for Power Tools |
Grip Style Grip Style |
|---|
 |  |
| Plain | Cushion |
 | |
| Ultra Grip |
Shaft Material Shaft Material |
|---|
|
Bit-Holding Mechanism Bit-Holding Mechanism |
|---|
|
Shaft Finish Shaft Finish |
|---|
|
DFARS (Defense Acquisition Regulations Supplement) DFARS (Defense AcquisitionRegulations Supplement) |
|---|
RoHS (Restriction of Hazardous Substances) RoHS (Restriction ofHazardous Substances) |
|---|
|
REACH (Registration, Evaluation, Authorization and Restriction of Chemicals) REACH (Registration,Evaluation, Authorization and Restriction of Chemicals) |
|---|
|
Container Type Container Type |
|---|
|
For Use On For Use On |
|---|
|
|
About Countersinks
Countersinks cut a cone-shaped opening to install screws and rivets flush with a surface or hold workpieces between centers on a lathe. They can also be used for chamfering and deburring.
More
Tight-Clearance Ratcheting Bit Screwdrivers
A ratchet mechanism allows you to drive fasteners when there's little space to move the handle.
Style A have an offset head to access screws in obstructed areas. A retaining ring holds the bit, and the plastic handle provides comfort and a secure grip.
Style B accept two shank sizes, held in place by magnets.
Style C accept two shank sizes and have offset heads to access screws in obstructed areas. Magnets hold the bits.
Style E have seven interchangeable bits—all of which are compatible with power tools. Store them inside the handle so they don’t get lost or misplaced when you’re not using them. Bits are held in place by magnets. To use these screwdrivers as a nutdriver, remove the bit and turn fasteners with the shaft.
Material | ||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Style | For Bit Hex Shank Size | Number of Sizes | Sizes Included | Overall Lg. | Offset Angle | Bit-Holding Mechanism | Shaft | Bit | Handle | Features | Each | |
| A | 1/4" | __ | __ | 4 1/8" | 10° | Retaining Ring | Chrome-Plated Steel | __ | Plastic | __ | 00000000 | 000000 |
| B | 1/4", 5/16" | __ | __ | 5 1/2" | __ | Magnet | Chrome-Plated Steel | __ | Steel | __ | 00000000 | 00000 |
| C | 1/4", 5/16" | __ | __ | 5 3/8" | 25° | Magnet | Chrome-Plated Steel | __ | Steel | __ | 00000000 | 00000 |
| E | 1/4" | 8 | External Hex: 1/4" Phillips: No. 1, No. 2 Slotted: 1/4", 3/16" Square: No. 1, No. 2 Torx: T15 | 4 5/8" | __ | Magnet | __ | Steel | Plastic | Bit storage inside tool | 00000000 | 00000 |
Ratcheting Bit Screwdrivers
A ratchet mechanism turns fasteners more quickly than a standard driver. Insert a bit into the shaft and a magnet holds it in place.
T-handle drivers have a longer reach and make it easier to turn fasteners from above.
Ultra-grip drivers have a multicomponent handle that provides comfort and the best possible grip for achieving maximum torque.
Shaft | Material | |||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| For Bit Hex Shank Size | Number of Sizes | Sizes Included | Overall Lg. | Lg. | O'all Wd. | Bit-Holding Mechanism | Shaft | Bit | Handle | Grip Style | Driver Style | Features | Each | |
| 1/4" | 1 | Phillips: No. 2 | 3 7/8" | 2" | 3/8" | Magnet | Stainless Steel | Steel | Plastic | Plain | T-Handle | __ | 0000000 | 000000 |
| 1/4" | 1 | Phillips: No. 2 | 5 13/16" | 3 7/8" | 3/8" | Magnet | Stainless Steel | Steel | Plastic | Plain | T-Handle | __ | 0000000 | 00000 |
| 1/4" | 1 | Phillips: No. 2 | 9 3/4" | 7 7/8" | 3/8" | Magnet | Stainless Steel | Steel | Plastic | Plain | T-Handle | __ | 0000000 | 00000 |
| 1/4" | 10 | Phillips: No. 1, No. 2 Slotted: 3/16", 1/4" Torx: T10, T15 Square: No. 1, No. 2 Pozidriv®: No. 1, No. 2 | 10" | 3" | 3/8" | Magnet | Chrome-Plated Steel | Steel | Plastic | Ultra Grip | Driver | Bit storage inside tool | 0000000 | 00000 |
Fast-Driving Ratcheting Bit Screwdrivers
Drive screws four times faster than ratcheting alone. Grip the speed housing at the base of the shaft with one hand while turning the handle with the other. These tools have a magnet at the end of the shaft that holds bits in place. The contoured ultra-grip handle provides comfort and the best possible grip for achieving maximum torque.
Shaft | Material | |||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| For Bit Hex Shank Size | Number of Sizes | Sizes Included | Overall Lg. | Lg. | O'all Wd. | Bit-Holding Mechanism | Shaft | Bit | Handle | Features | Each | |
| 1/4" | 4 | Phillips: No. 1, No. 2 Slotted: 3/16", 1/4" | 9 1/4" | 2 7/8" | 3/8" | Magnet | Stainless Steel | Steel | Rubber | Bit storage inside tool | 0000000 | 000000 |
Bit Screwdrivers
Insert a bit into the shaft and a magnet holds it in place.
Tamper-resistant hex are also known as pin-in-hex.
Tamper-resistant Torx are also known as pin-in-Torx.
Shaft | Material | |||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| For Bit Hex Shank Size | No. of Sizes | Sizes Included | O'all Lg. | Lg. | O'all Wd. | Shaft | Bit | Handle | Grip Style | Features | Each | |
| 1/4" | 5 | Tamper-Resistant Hex: 3/32", 1/8", 5/32", 3/16", 7/32" | 8" | 3 1/4" | 3/8" | Black-Oxide Steel | Steel | Plastic | Plain | __ | 0000000 | 000000 |
| 1/4" | 6 | Phillips: No. 1, No. 2, No. 3 Slotted: 3/16", 7/32", 1/4" | 8" | 4" | 13/32" | Black-Oxide Aluminum | Steel | Plastic | Plain | Bit storage inside tool | 0000000 | 00000 |
| 1/4" | 6 | Torx: T10, T15, T20, T25, T30, T40 | 9 1/4" | 4 3/4" | 7/16" | Nickel-Plated Steel | Steel | Plastic | Plain | __ | 0000000 | 00000 |
| 1/4" | 10 | External Hex: 1/4", 5/16" Tamper-Resistant Torx: T7, T8, T9, T10, T15, T20, T25, T27 | 9 1/2" | 4" | 7/16" | Nickel-Plated Steel | Steel | Steel | Plain | __ | 0000000 | 00000 |
Secure-Hold Bit Screwdrivers
 | Phillips |
Slotted |
Lock your bit into the chuck to prevent accidental disengagement. Pull back on the chuck to insert a bit in the magnetic holder; push it forward to lock it in place.
Shaft | Material | ||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| For Bit Hex Shank Size | Number of Sizes | Sizes Included | Overall Lg. | Lg. | O'all Wd. | Bit-Holding Mechanism | Shaft | Bit | Handle | Features | Container Type | Each | |
| 1/4" | 6 | Phillips: No. 1, No. 2, No. 3 Slotted: 3/16", 7/32", 1/4" | 8" | 3 1/4" | 5/8" | Quick-Change Chuck | Steel | Steel | Plastic | Pop-up bit storage inside tool, Removable Telescoping Shaft | Fabric Case | 0000000 | 000000 |
Illuminated Bit Screwdrivers
LEDs light the tip so you can use these tools dark areas. Bits have a different tip at each end and snap into the shaft.
Shaft | Material | ||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|
| For Bit Hex Shank Size, mm | Number of Sizes | Sizes Included | Overall Lg. | Lg. | O'all Wd. | Shaft | Bit | Handle | Batteries Included | Each | |
| 4 | 8 | Phillips: No. 000, No. 0 Slotted: 5/64", 1/8" Torx: T5, T6, T8, T10 | 5 3/4" | 7/8" | 5/16" | Plastic | Steel | Plastic | Yes | 0000000 | 000000 |
Electrical-Insulating Bit Screwdrivers
An insulated handle and shaft protect against shock from accidental contact with live electrical circuits. These tools are tested to 1,000 volts to meet IEC 60900 and EN 60900. A magnet holds the bit in place.
Shaft | Material | |||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| For Bit Hex Shank Size | Number of Sizes | Sizes Included | Overall Lg. | Lg. | O'all Wd. | Bit-Holding Mechanism | Shaft | Bit | Handle | Specifications Met | Each | |
| 1/4" | 13 | Phillips: No. 0, No. 1, No. 2, No. 3 Slotted: 5/32", 7/32", 1/4" Square: No. 1, No. 2, No. 3 Torx: T15, T20, T25 | 9 1/8" | 3 3/8" | 0.48" | Magnet | Plastic-Coated Steel | Steel | Plastic | IEC 60900, EN 60900 | 0000000 | 000000 |
Reversible-Bit Screwdriver/Nutdrivers
Bits have a different tip at each end and snap into the shaft. A ball detent holds the bit in place. To use as nutdriver, remove the bit and turn fasteners with the shaft, which is also reversible.
Ultra-grip drivers have a multicomponent handle that provides comfort and the best possible grip for achieving maximum torque. For those without a voltage detector, bits turn four screw sizes and the shaft two external hex sizes. Those with a voltage detector safely test for AC voltage without contacting live wires. Light and sound indicators alert you when over 50 volts AC is detected. The detector is attached to the tool’s handle; remove it from the handle to use it on its own. Bits turn eight screw sizes and the shaft three external hex sizes.
Cushion-grip drivers offer comfort and some slip resistance. Bits turn eight screw sizes and the shaft three external hex sizes.
Shaft | Material | |||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| For Bit Hex Shank Size | No. of Sizes | Sizes Included | Overall Lg. | Lg. | O'all Wd. | Bit-Holding Mechanism | Shaft | Bit | Handle | Batteries Included | Specifications Met | Features | Each | |
Ultra Grip | ||||||||||||||
| 1/4", 5/16" | 6 | Phillips: No. 1, No. 2 Slotted: 3/16", 1/4" External Hex: 1/4", 5/16" | 7 3/4" | 2 1/4" | 7/16" | Ball Detent | Chrome-Plated Steel | Steel | Plastic | __ | __ | Bit storage inside shaft | 0000000 | 00000 |
| 1/4", 5/16" | 10 | Phillips: No. 1, No. 2 Slotted: 3/16", 1/4" Torx: T10, T15 Square: No. 1, No. 2 External Hex: 1/4", 5/16" | 9" | 3 3/8" | 1 1/4" | Ball Detent | Plastic-Coated Steel | Steel | Plastic | Yes | C-UL Listed, UL Listed | Bit storage inside shaft, Bit storage inside tool, Voltage Detector | 0000000 | 00000 |
Cushion Grip | ||||||||||||||
| 1/4", 5/16" | 11 | Phillips: No. 1, No. 2 Slotted: 3/16", 1/4" Torx: T10, T15 Square: No. 1, No. 2 External Hex: 1/4" External Hex: 5/16", 3/8" | 7" | 2 1/2" | 17/32" | Ball Detent | Chrome-Plated Steel | Steel | Plastic | __ | __ | Bit storage inside shaft | 0000000 | 00000 |
Stubby Reversible-Bit Screwdriver/Nutdrivers
When working in tight spaces, these short drivers fit where others can't. Bits have a different tip at each end and snap into the shaft. A ball detent holds the bit in place. To use as nutdriver, remove the bit and turn fasteners with the shaft, which is also reversible and turns two external hex sizes. Drivers have a cushion grip for comfort and some slip resistance.
Shaft | Material | |||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| For Bit Hex Shank Size | Number of Sizes | Sizes Included | Overall Lg. | Lg. | O'all Wd. | Bit-Holding Mechanism | Shaft | Bit | Handle | Features | Each | |
| 1/4", 5/16" | 6 | Phillips: No. 1, No. 2 Slotted: 1/4", 3/16" External Hex: 1/4", 5/16" | 3 3/8" | 1 1/4" | 17/32" | Ball Detent | Chrome-Plated Steel | Steel | Plastic | Bit storage inside shaft | 0000000 | 000000 |
Quick-Change Combination Countersinking Drill and Screwdriver Bit Sets
Fasten differently sized screws with these sets. They save you the effort of switching three separate bits in and out of a power tool, instead letting you flip between a countersinking drill and a screwdriver bit with a single hand. You can also attach your own countersinking drills and screwdriver bits as long as they have a 1/4” hex shank.
Countersinking drills have an 82° angle, allowing inch-sized flat- and oval-head screws to sit flush with the surface.
| No. of Pieces | Includes | Countersink Angle | Countersink Body Dia. | No. of Countersink Flutes | Adapter Hex Shank Size | For Use On | Each | |
Black-Oxide High-Speed Steel Countersink | ||||||||
|---|---|---|---|---|---|---|---|---|
| 11 | 1 Drill-Bit Countersink for 3/32" Drill Bit 1 Drill-Bit Countersink for 7/64" Drill Bit 1 Drill Bit (3/32" Drill Bit Size) 2 Drill Bits (7/64" Drill Bit Size) 1 Phillips No. 1 Screwdriver Bit (1" O'all Lg.) 2 Phillips No. 2 Screwdriver Bits (1" O'all Lg.) 1 Reversible Shaft 1 Adapter 1 Hex L-Key | 82° | 3/8" | 4 | 5/16" | Aluminum, Fiberglass, Plastic, Wood | 0000000 | 000000 |
Quick-Change Combination Countersinking Drill and Screwdriver Bits
Drill, countersink, and drive screws without switching three separate bits in and out of your power tool. With a single hand, flip between drilling countersunk holes and driving screws. The countersinking drill and screwdriver bit are secured with set screws, so you can switch them out for any bits with a 1/4” hex shank.
The countersinking drill has an 82° angle, allowing inch-sized flat- and oval-head screws to sit flush with the surface.
For technical drawings and 3-D models, click on a part number.
Combination Countersinking Drill and Screwdriver Bits | Replacement Drill Bits | ||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| For Screw Size | Drill Bit Size | Countersink Body Dia. | Max. Hole Drilling Dp. | Countersink Angle | Screwdriver Bit Size | For Drive Style | Adapter Hex Shank Size | Adapter Lg. | For Use On | Each | Each | ||
Black-Oxide High-Speed Steel Countersink | |||||||||||||
4 Countersink Flutes | |||||||||||||
| No. 6 | 3/32" | 3/8" | 1 3/4" | 82° | No. 2 | Phillips | 5/16" | 3 3/4" | Aluminum, Fiberglass, Plastic, Wood | 0000000 | 000000 | 0000000 | 00000 |
| No. 8 | 7/64" | 3/8" | 2" | 82° | No. 2 | Phillips | 5/16" | 3 3/4" | Aluminum, Fiberglass, Plastic, Wood | 0000000 | 00000 | 0000000 | 0000 |
| No. 10 | 1/8" | 3/8" | 2 1/4" | 82° | No. 2 | Phillips | 5/16" | 3 3/4" | Aluminum, Fiberglass, Plastic, Wood | 0000000 | 00000 | 0000000 | 0000 |