These switches are UL listed for environments with flammable gases and combustible dust. They activate or deactivate equipment when the flow rate reaches your set point. All are single pole, double throw (SPDT) and can be installed to turn one circuit from “off” to “on” (normally open) or from “on” to “off” (normally closed).

Switches with a brass body meet NEC Class I, Divisions 1 and 2, Groups B, C, and D; and NEC Class II, Divisions 1 and 2, Groups E, F, and G.

Switches with a 304 stainless steel body are more corrosion resistant than switches with a brass body and meet NEC Class I, Divisions 1 and 2, Groups A, B, C, and D; and NEC Class II, Divisions 1 and 2, Groups E, F, and G.

For technical drawings and 3-D models, click on a part number.

For applications with a variable flow rate in environments with flammable gases and combustible dust, these UL-listed switches have an adjustment screw to alter the set point. They activate or deactivate equipment when the flow rate reaches your set point. All are single pole, double throw (SPDT) and can be installed to turn one circuit from “off” to “on” (normally open) or from “on” to “off” (normally closed).

Switch with a brass body meets NEC Class I, Divisions 1 and 2, Groups B, C, and D; and NEC Class II, Divisions 1 and 2, Groups E, F, and G.

Switch with a 304 stainless steel body is more corrosion resistant than the switch with a brass body. It meets NEC Class I, Divisions 1 and 2, Groups A, B, C, and D; and NEC Class II, Divisions 1 and 2, Groups E, F, and G.

For technical drawings and 3-D models, click on a part number.

For installation in environments with flammable gases and combustible dust, these flow switches are UL listed for hazardous locations. They meet NEC Class I, Divisions 1 and 2, Groups C and D; and NEC Class II, Divisions 1 and 2, Groups E, F, and G. They’re installed in tees or pipe outlets to detect the flow rate of liquid in contact with the sensing paddle. Switches activate or deactivate equipment when the flow rate reaches your set point. All come with five sensing paddles that can be trimmed to fit a range of pipe sizes. The flow rate varies based on the pipe size and paddle used.

SPDT switches control one circuit. They can be installed to turn the circuit from “off” to “on” (normally open) or from “on” to “off” (normally closed).

DPDT switches control two circuits. They can be installed to turn both circuits from “off” to “on” (normally open) or from “on” to “off” (normally closed).

Switches with a 316 stainless steel body are more corrosion resistant than switches with a brass body.

For technical drawings and 3-D models, click on a part number.

The correlated scale and conversion charts let you use the same flowmeter to measure the flow rate of nitrogen, oxygen, argon, and helium. These flowmeters have fittings on the back for installation in your instrument panel. The flow-control knob lets you open and close the valve at the inlet to adjust the flow rate within the range.

316 stainless steel fittings are more corrosion resistant than aluminum fittings.

For technical drawings and 3-D models, click on a part number.

Adjust the flow by turning the screw. Use these mufflers with air-powered tools and cylinders to reduce noise and filter exhaust fumes.

For mufflers with an external hex drive, twist the screw and then tighten the hex nut with a wrench to secure. These mufflers are more secure than those with a thumb screw.

For mufflers with a thumb screw, twist the screw and friction secures them in place—no need to use a wrench. Often used in valve exhaust ports, these mufflers are not as secure as those with a nut.

Brass, bronze, and nylon mufflers offer good corrosion resistance.

Stainless steel mufflers offer excellent corrosion resistance.

For technical drawings and 3-D models, click on a part number.