Extend your reach in hard-to-access areas—turn these valves on and off using a square ratchet to grasp the hole at the end of the handle. Use with water, oil, air, and inert gas.

Attach a pressure gauge to the side port on these valves. Use with water and air.

A built-in strainer traps debris and allows you to replace the screen without disconnecting your pipeline.

These valves can handle at least twice the pressure of other compact valves. Install them in tight spots. Use with water, oil, air, and inert gas.

Maintain and repair these valves without unthreading pipe connections. They have a three-piece bolted body that disassembles inline for access to internal components. Use with water, oil, air, inert gas, and steam.

For fast installation and removal from pipelines, these valves have a union fitting that disassembles into multiple pieces. They’re for use with water, oil, air, inert gas, and steam.

Use these valves with water, air, and inert gas.

These valves have union fittings that disassemble for fast installation and removal from pipelines. Use with water, air, and inert gas.

Attach these valves to industry-standard two-bolt flanges on circulation pumps from manufacturers such as Bell and Gossett, Taco, Grundfos, and Armstrong. Use with water, air, and steam.

Insert tubing into the fittings on these valves—no heat, solder, or flux required. They’re for use with water, oil, air, and inert gas.

For more durability than plastic valves, these are made of metal. A compression sleeve bites into tubing as you tighten the nut, forming a strong seal. Use these valves with water, oil, air, inert gas, and steam.

Attach gauges or sensors to these valves so you can remove them for maintenance and calibration without depressurizing your line. They are also known as block and bleed valves.

For chemical-processing applications in confined areas, these valves have an EPDM seal and a PVC or CPVC body to withstand aggressive and corrosive solutions and a low-profile handle to fit in tight spots.

The three-piece bolted body comes apart for access to internal components without unthreading pipe connections and removing the valve from your line. Seal is fluoroelastomer and body is polypropylene for excellent resistance to aggressive and corrosive solutions in chemical-processing applications.

Union fittings on both ends of these valves disassemble for fast installation and removal from your pipeline. Insert unthreaded pipe into the socket ends and bond with primer and cement to create a permanent, leak-tight connection. These valves have a fluoroelastomer seal and a plastic body that can withstand aggressive and corrosive solutions in chemical-processing applications.

Barbs grip onto tubing, providing a secure hold. To withstand aggressive and corrosive solutions in chemical-processing applications, these valves have a plastic body and a chemical-resistant seal.

Use these valves with garden hose and other landscaping equipment. All meet NSF/ANSI 61 for use with drinking water.

Disassemble the union fittings on these valves for fast installation and removal from your pipeline. All meet NSF/ANSI 61 for use with drinking water.

With 45° flared tube fittings, these valves form a tight seal on metal tubing lines for natural gas, propane, and butane.

For use in general purpose applications with water, oil, and inert gas.

Maintain and repair these valves without unthreading pipe connections. They have a three-piece bolted body that disassembles inline for access to internal components.

Separate the union fittings on each end of these valves for fast installation and removal from pipelines.

All valves have threaded NPT connections.

Threads and a hex nut below the handle let you install these valves through instrument panels. They are for use with water, oil, air, and inert gas. All divert flow between ports.

For a lightweight alternative to metal valves, these have a plastic body. To fit in tight spots, they have a low-profile handle and a short end-to-end length. Valves are for use with water, oil, air, and inert gas. All divert flow between ports.

For easy installation and removal from pipelines, all ends on these valves have union fittings that disassemble into multiple pieces. Use with water. Valves divert flow between ports.

Perform valve maintenance without unthreading pipe connections. These valves have a three-piece bolted body that comes apart for inline access to internal components. The fluoroelastomer seal and glass-filled polypropylene body can withstand aggressive and corrosive solutions for diverting flow in chemical-processing applications.

To divert flow between ports in drinking water lines, these valves meet NSF/ANSI 61.

Often installed on petroleum loading arms to test fuel quality without interrupting flow, these valves are fire-tested to meet American Petroleum Institute (API) 607, Edition 5, for securely isolating fluid and preventing the spread of fire.

The motor on these valves can handle diverting applications with high flow rates and pressures. They operate on electricity to automatically divert flow between ports.

Lock the handle using a padlock.