Also known as troffers, these lights fit most standard drop-ceiling grids, so they’re often used in indoor spaces such as offices and storage rooms. They can be hardwired to operate on any of the voltages listed.

Lights with a solid lens are frosted and smooth or prismatic to disperse light evenly. With built-in LEDs, these lights last longer, are more efficient, and generate less heat than fluorescent lights. They emit a neutral white light often found in workspaces.

Lights with a parabolic lens are reflective to direct light downward and reduce glare. They require fluorescent bulbs (sold separately).

These fixtures disperse light from the top, bottom, and side to produce ambient lighting. They mount to the wall so they're often used in enclosed spaces such as stairwells, hallways, and storage rooms. Rated for use in damp locations, these lights withstand humidity and moisture. They have built-in LEDs, which last longer, are more efficient, and generate less heat than fluorescent lights. The lens is smooth and frosted to disperse light evenly. They can be hardwired to operate on any of the voltages listed.

For technical drawings and 3-D models, click on a part number.

Mount these lights flush with ceilings in wet locations—all are sealed to keep out humidity and dripping, splashing, and falling liquids. Unlike recessed can lights, which require a separate housing, these fit directly into a cutout in your ceiling and are held in place by springs. With built-in LEDs, these lights last longer, are more efficient, and generate less heat than other light technologies. Use the switch on the power supply to choose between warm, cool, or neutral light—no more mismatched lights. All have passed strict U.S. and Canadian safety standards.

For technical drawings and 3-D models, click on a part number.

Mount lights in recessed spaces so the lens is flush with the wall. These fixtures are ETL and C-ETL listed for Class I, Division 2, Groups A, B, C, and D; and Class II, Division 2, Groups F and G for use where ignitable concentrations of hazardous material occur infrequently, such as in the case of an accidental spill or failure of a ventilation system. They withstand acetylene, hydrogen, ethylene, propane, carbonaceous dusts, and nonconductive dusts. These lights are often used in freestanding buildings, such as paint spray booths, so the back opens like a door for changing light bulbs from the outside. They can be hardwired to operate on any of the voltages listed. They work with tubular fluorescent bulbs (sold separately).

Mount these lights into a recessed opening in your machine—they sit flush against the surface for a streamlined appearance. They have a durable tempered-glass lens that's sealed to keep out fluids, chips, and shavings. These lights are rated IP67 to withstand temporary submersion in a maximum of one meter of water for up to 30 minutes, so they're built tougher than needed for machine environments. With built-in LEDs, these lights last longer, are more efficient, and generate less heat than other light technologies. They cast a cool light that highlights white/blue tones, which is good for inspecting.

Brackets that are sold separately are an alternative mounting option. While not required, they clip onto the light anywhere along its length; this permits you to put the mounting fasteners in a place that works for your machine.

Power supplies, also known as transformers, convert your facility’s 120 or 240 AC voltage into 24 DC voltage, which is required to operate these lights. They cannot be sold to California or Vermont due to local energy efficiency requirements.

Similar in function to tubular machine lights, except strip machine lights have a flat lens that directs light downward. These lights are sealed to keep out fluid, chips, and shavings, so they can be mounted directly inside machines. With built-in LEDs, these lights last longer, are more efficient, and generate less heat than other light technologies. They produce a cool or daylight appearance that highlights white/blue tones, which is good for inspecting.

All lights are rated IP67 to withstand temporary submersion in a maximum of one meter of water for up to 30 minutes, so they're built tougher than needed for machine environments.

Style B lights have a magnetic mounting base for quick, temporary installation, as well as through holes for permanent mounting. They have a tempered glass lens that's more durable than acrylic plastic.