Create a strong joint in a blind hole.

More corrosion resistant than 18-8 stainless steel screws, these have excellent resistance to chemicals and salt water.

Brass screws are corrosion resistant in wet environments and electrically conductive.

Beveled under the head for use in countersunk holes, these steel screws press threads into material for a tight, secure hold.

Brass screws are corrosion resistant in wet environments and electrically conductive.

These steel screws are zinc plated to resist corrosion in wet environments.

18-8 stainless steel screws have good chemical resistance.

More corrosion resistant than 18-8 stainless steel screws, these have excellent resistance to chemicals and salt water.

These steel screws have corrosion-resistant finishes.

These 316 stainless steel screws have excellent resistance to chemicals and salt water.

18-8 stainless steel screws have good chemical resistance.

These Phillips head screws have a decorative rounded top that provides a finished appearance.

These screws speed installation by drilling, tapping, and fastening wood and metal in a single operation.

Thread-forming screws press threads into drilled holes for a tight vibration-resistant assembly.

Because these steel screws cut threads into drilled holes as they’re turned, they require less driving torque and cause less stress on material than thread-forming screws. Also known as trim-head deck screws, they have a small flat head and slender shank to reduce the risk of splitting boards.

More corrosion resistant than 18-8 stainless steel screws, these have excellent resistance to chemicals and salt water.

Also known as deck screws, these Phillips screws have a sharp point and narrow body to penetrate softwood and plastic-wood composite decking material.

More corrosion resistant than 18-8 stainless steel screws, these have excellent resistance to chemicals and salt water.

These steel screws are zinc plated to resist corrosion in wet environments.

18-8 stainless steel screws have good chemical resistance.

These Phillips head screws have a decorative rounded top that provides a finished appearance.

Large threads cut into softwood such as particleboard for a strong hold.

Made from brass, these inserts are nonmagnetic, mildly corrosion resistant, and electrically conductive.

These 18-8 stainless steel inserts have excellent resistance to chemicals and may be mildly magnetic.

Steel inserts have high strength for durability.

The most corrosion resistant tee nut inserts we offer, these inserts stand up to chemicals and salt water.

Fewer prongs than other tee nut inserts reduce the risk of splitting hardwood—these inserts have three short prongs.

Use where vibration is a concern—these tee nut inserts have distorted threads that lock screws in place.

An open end allows long screws and bolts to pass through the insert.

Knurls hold these inserts in hardwoods such as oak, maple, and walnut to prevent twisting.

With the male threaded end on these inserts, mount components directly to plastic parts.

The tapered shape makes it easier to guide these inserts into a hole during installation. Use a drill bit to create a straight hole, then taper the top half.

The flange keeps these inserts from pulling through a hole. Press them in from the underside of material, and install a screw from the top of material.

Made from brass, these inserts are electrically conductive, nonmagnetic, and have good corrosion resistance.

These aluminum inserts are 70% lighter than brass inserts, electrically conductive, and nonmagnetic. They have good corrosion resistance, which is comparable to brass but not as good as stainless steel.

These 18-8 stainless steel inserts have better corrosion resistance than brass inserts and may be mildly magnetic.

These aluminum inserts are 70% lighter than brass inserts, electrically conductive, and nonmagnetic. They have good corrosion resistance, which is comparable to brass but not as good as stainless steel.

Press these inserts into a drilled hole and the flexible metal teeth anchor them in the material. Use them with carbon fiber, fiberglass, and garolite.

Made of compressed wood, these biscuits fit into slots cut into wood. When glued, they expand for a tight fit.

Use these as pivot or hinge pins. The knurled half locks pins in position, while the smooth half acts as a pivot.

These pins make good hinges or pivots. The grooved half locks pins in position, while the smooth half can act as a pivot. Also known as type H pins.

Slip these pins in and out during maintenance or prototyping—they’re undersized to make alignment easier.

Plastic pins are a nonconductive and nonmagnetic alternative to metal dowel pins. Use them as pivots, hinges, shafts, jigs, and fixtures to locate or hold parts.

Center-groove pins are often used in place of clevis pins or to create T-handles. The grooved center locks pins in position, while the smooth ends act as a pivot. Also known as type E pins.

The flat side of these pins relieves trapped air, making them easier to insert in and remove from blind holes. To remove, thread a screw or tool into the tapped hole, then pull the pin out.

Barbs bite into plastics and soft metals such as aluminum for a strong hold, and a round head gives a finished appearance.

To remove these pins, thread a screw or tool into the tapped hole, then pull them out.

These pins are commonly used as anchors for tension springs. The grooved half locks pins in position, and spring ends fit in to the notch. Also known as type G pins.

Quarter-groove pins are well suited for hinges or pivots. The grooved end locks pins in position, while the smooth portion can act as a pivot. Also known as type C pins.