Also resistant to water and salts.

These neoprene gasket sheets are reinforced with a nylon insert to prevent them from losing shape while under pressure up to 1,000 psi.

Made from a blend of cork and rubber, this material is commonly used for low-pressure applications.

This material withstands temperatures up to 850° F and pressure up to 2,000 psi.

Stick these gaskets around door and vent cutouts or replace worn seals to maintain your enclosure's NEMA rating.

Very soft and conformable, this expanded PTFE gasket tape compresses into an extremely thin profile. Use it to create a leak-resistant seal in tight-tolerance applications, such as on precision machinery.

This material resists boric acid, citric acid, isopropyl alcohol, fuel, and oil.

These seals are made of solid EPDM foam rubber.

The hollow construction on these seals provides better compressibility than solid rubber seals. Made of silicone rubber, they also resist water and salts.

These solid silicone rubber seals also stand up to water and salts.

It’s the hollow construction that makes these seals more compressible than solid seals. Made of silicone foam rubber, they also resist water and salts.

Use these Viton® fluoroelastomer rubber seals with fuels and aggressive chemicals, such as petroleum oil, hydrofluoric acid, and propyl alcohol.

These hollow seals offer better compressibility than solid seals.

The foam core makes these vinyl rubber seals firmer and more durable than hollow seals. They also resist salts and detergents.

Made of Viton® fluoroelastomer rubber, these seals stand up to fuels and aggressive chemicals, such as petroleum oil, hydrofluoric acid, and propyl alcohol.

These loosely knitted fiberglass seals are more flexible, compressible, and conformable than High-Temperature Rope Edge Seals.

Made of 96% silica, these seals resist temperatures up to 1800° F.

Made from tightly woven calcium alumina silicate, these seals can handle temperatures from –300° to 1100° F.

These seals have a strong Inconel core covered with woven silica yarn that’s been treated to withstand temperatures up to 2300° F. They resist most refrigerants, salts, and grease.

A ceramic cover makes these seals more chemical resistant than the seals with a silica cover. They resist acids (except hydrofluoric and phosphoric), diluted alkalies, most refrigerants, salts, and grease. Seals can withstand temperatures up to 1700° F.

The X shape of this cord stock provides four points of contact for a better seal in dynamic applications than round profile. It also requires less compression to make a seal, so it offers a longer service life.

This square-profile cord stock has flat edges on all four sides, which creates a better seal than round profile in static applications, such as hose, pipe, and faucet connections.

This cord stock is softer and creates a better seal in low-pressure applications than standard fluoroelastomer cord stock.

Use neoprene cord stock to make O-rings for applications that come into contact with water.

This cord stock is softer and creates a better seal than standard silicone cord stock in low-pressure applications up to 400° F.

Create round-profile O-rings for sealing applications near ovens and other hot areas in your food plant.

In addition to having good resistance to water, sunlight, and oxidation, these neoprene foam sheets and strips resist swelling when they come into contact with oil.

Made of EPDM foam, these sheets and strips have the best resistance to water, sunlight, and oxidation of all the foam we offer.

These vinyl foam sheets and strips are so conformable that once they're compressed they won't fully spring back. Use them to fill gaps and seal uneven surfaces.

This premium silicone is the most resilient foam we offer. It is equivalent to Cohrlastic and is also known as Norseal and silicone sponge.

One layer of fiberglass fabric is sandwiched between layers of silicone foam giving these strips strength to handle high-stress applications, such as gasketing.

Even after exposure to sunlight, rain, and snow, these silicone foam strips remain flexible.

Even after extended compression, these sheets and strips will bounce back to shape.

Good for tough vacuum-sealing and low closure-force applications, these polyurethane foam sheets and strips have open/closed cells to keep water, air, and gases from being absorbed when they are compressed at least 25%. Even after extended compression, all bounce back to shape faster than other foams we offer.

Often used for impact pads, gaskets, and enclosure seals, these polyurethane foam sheets and strips absorb shock better than other resilient foam.

Made from a blend of Buna-N, neoprene, and vinyl, these foam strips have good resistance to oil.

Offering excellent resistance to corrosive environments, these Viton® fluoroelastomer foam sheets and strips stand up to a wide variety of chemicals, fuels, and oils.

These platinum-cured silicone rubber sheets and strips meet the strict purity standards of USP Class VI.

Made from FDA-compliant materials for use with food and beverage, these sheets and strips won’t degrade from animal and vegetable oils.

Seal T-slots, rail ends, and gaps between rails to keep out dust, debris, and other contaminants.

Fill irregularities in valve stem with these soft PTFE seals.

These lubricated PTFE fiber seals stand up to most chemicals. Use them in pumps and valves.

Built for high-speed pump and valve applications, these super-tough seals are made of expanded-graphite yarn with carbon-yarn corners.

Made of ePTFE with a graphite filler and reinforced by Aramid, these seals combine heat protection with chemical and abrasion resistance.

Use these graphite-impregnated graphite seals for steam applications in pumps and valves.

Made of graphite-impregnated carbon, these steam-resistant seals dissipate heat from the shaft to protect pumps and valves when operating at high speeds.

Our most compressible packing seals, these require less pressure than any other to make an effective seal. They’re made of lubricated PTFE-impregnated aramid fiber and are for use in pumps.

The most abrasion resistant of all our packing seals, these are made of PTFE-impregnated aramid fiber that has been saturated in a lubricant. They are for use in pumps.

Also known as Macor, these glass-mica ceramic sheets and bars withstand temperatures up to 1470° F.