With output shaft openings on both sides, these speed reducers adapt to fit multiple configurations. Mount to a NEMA 56C motor.

Mount these speed reducers to a NEMA 56C motor.

The input and output shafts are positioned at the same height, so these speed reducers take up less than half the vertical space as our standard right-angle speed reducers.

Mount right-angle speed reducers to machinery or other surfaces where access from the bottom is not possible.

With shaft diameters of 3/8" and larger, these gear boxes transmit higher speeds and greater torque than Compact Right-Angle Gear Boxes.

For small machinery and tight spots, these gear boxes have 1/4" diameter and smaller shafts and a footprint of less than 2½" square.

Worm gears use screw threads to reduce shaft speed by ratios of 10:1 and greater while transmitting motion at a right angle.

A type of miter gear where one gear is smaller than the other, bevel gears provide right-angle speed reduction at ratios ranging from 2:1 to 5:1. They’re more efficient than worm gears because they create less friction.

Also known as spiral miter gears, these gears have curved teeth that gradually engage and stay in contact longer than straight teeth so they handle heavier loads at higher speeds. Speed ratio is 1:1.

For smooth, quiet operation at high speeds under heavy loads, helical gears have curved teeth that engage gradually and stay in contact longer than straight teeth.

These plastic gears are lighter and quieter than metal gears—pair them with metal worms for lubrication-free operation. Worm gears use screw threads to make large reductions to shaft speed while transmitting motion at a right angle.

Reduce speeds where noise, corrosion, and frequent lubrication are a concern. Compared to metal gears, these nylon gears run more quietly, won't rust, and don't need to be lubricated.

Compared to plastic gears, metal gears are better for high-load, high-speed, and heavy duty applications.

Broad, strong Acme threads make these screw jacks better than ball screw jacks for heavy loads, intermittent positioning applications, and where vibration is present.

Add a flat mounting surface to to a screw jack to support loads.

Add a flat mounting surface to a ball screw jack to support loads.

Combine with a machine key to transmit torque to gears, sprockets, and other power transmission components.

In addition to diameter tolerances that are twice as tight as standard keyed shafts, these shafts include a traceable lot number and test report. Use them with machine keys to transmit torque to gears, sprockets, and other power transmission components.

Mount the flange to a machine or wall to support idler sprockets and pulleys in tensioning applications. They include washers and a nut to position your component and hold it in place.

Connect these internally threaded shafts directly to threaded components, or use a fastener to secure.

Eight times straighter than standard rotary shafts, these tight-tolerance shafts minimize vibrations and reduce wear to bearings and other components. They also have diameter tolerances that are twice as tight as standard rotary shafts.

Attach threaded accessories, such as mixer propellers and fan blades, to the end of these shafts.

Connect these internally threaded shafts directly to threaded components, or use a fastener to secure. They have a flat surface area that allows set screws to dig into the shaft for securely mounting gears, sprockets, and bearings.

From one compact system, transmit linear or rotary motion or both at once (sometimes called spiral motion). Because of these different motions, these ball screw/splines and bearings create efficient, fluid movements in complex automated applications, such as pick-and-place robots.

Mount these externally threaded shafts into tapped holes rather than using a shaft support, or attach a hex nut, shaft collar, or other threaded accessory.

Keep a material certificate on hand for compliance and quality assurance needs. Certificates include a traceable lot number and material test report. These hollow shafts reduce system weight and allow you to run various media such as electrical wiring, compressed air tubing, coolants, or lubricants through the center.

Internal threads allow you to mount these shafts onto threaded studs and fasteners, no shaft supports needed.

For your compliance and quality assurance needs, these shafts come with a material certificate with a traceable lot number.

These shafts include a support rail for a stable setup that eliminates bending and prevents linear bearings from rotating.