These grips are sized to fit in tight areas.

Because these grips resist absorbing water, they are less likely to crack or corrode than other types of plastics and metals.

Wrap the split gland of these grips around ethernet cables with an RJ45 connector or other already installed cables for a water-resistant seal with your enclosure.

Extend your cord’s life while stopping it from coming loose in places that are sanitized with water or steam as hot as 300° F, such as food plants and clean rooms.

Snap these cord grips into place to secure cable in wet environments.

Secure cords installed through enclosures and panels in wet environments while protecting them against sharp bends. With a flared end that keeps cords from bending without limiting too much motion, these grips extend cord life.

These grips are made of nylon, which resists most chemicals. The nylon mesh extension provides a secure hold when the cable is pulled or in motion.

Secure cords in washdown areas where there’s minimal space—these cord grips curve 90° to relieve stress from bending.

These grips have an extension that provides extra support for moving cable and prevents kinking for longer cable life.

Secure cable installed through enclosures in wet environments while venting air to protect electronics from condensation.

Stop cords from coming loose in wet environments while keeping them along the side of your enclosure in tight spaces.

Use these lightweight grips to secure cords entering knockouts at a 45° angle in wet, tight spaces while easing the stress from bending. Made of aluminum, they’re lighter in weight than steel and brass grips yet durable.

Keep your cord at a gentle angle without sacrificing a tight hold, even in tough, wet environments.

These cord grips are lightweight yet durable.

The mesh extension provides a secure hold in applications where cable is pulled or in motion. It reduces stress on the cable and prevents kinking for longer cable life.

Made of nylon, these grips resist chemicals.

Built with snap-in tabs and a spring extension, these cord grips install into panel holes more quickly than standard grips and better prevent damage from sharp bends.

Stronger than aluminum cord grips, these grips are zinc plated for corrosion resistance.

Connect a single flat cable to a junction box.

Tighten the screws to secure your cable.

The mesh offers a secure hold in applications where cable is pulled or in motion. It reduces stress on the cable and prevents kinking for longer cable life.

Made of nylon, these grips resist chemicals. Install them in panels and enclosures—they have a zinc-plated steel locknut and metal-reinforced rubber O-ring that prevents liquid from entering the enclosure.

These cord grips are lightweight yet durable. They have a zinc-plated steel locknut and metal-reinforced rubber O-ring that prevents liquid from entering the connection.

These cord grips are lightweight yet durable. They have a zinc-plated steel locknut and metal-reinforced rubber O-ring that prevents liquid from entering the connection.

Stronger than aluminum cord grips, these grips are zinc plated for corrosion resistance. They have a steel locknut and metal-reinforced O-ring that prevents liquid from entering the connection.

These grips are nickel-plated brass for good corrosion resistance.

These grips meet Class III, Divisions 1 and 2 standards for use in hazardous locations.

FDA compliant for direct food contact, these cord grips have a multi-piece design to wrap around cables in sanitary environments without removing connectors or rewiring.

The face of these grips is flush with the cable-entry point for a seamless appearance. They have a thin, flexible seal that covers the holes until you push a cord through.

Modify these cord grips to get the right fit for your cord even when you don't know the exact diameter.

The face of these grips is flush with the cable-entry point for a seamless appearance.

Secure multiple flat cable through one cord grip—reducing the space and number you need for a project, as well as saving time.

A spring extension prevents sharp bends and kinks in your cord, prolonging its life. These bushings, which are more rigid than grommets, shield cords from rubbing against the edges of holes in enclosures and panels, so they won’t wear down.

Also known as Type B seals, these U-cups are wider than our other O-ring-loaded U-cup seals for better stability and fit in wider grooves.

Rated for pressure up to 10,000 psi, these leather U-cups handle over 80 times more pressure than our Buna-N U-cups.

Avoid common O-ring failure in dynamic applications—the square base of these seals prevents twisting, while backup rings protect against extrusion.

Rated for pressure up to 10,000 psi, these seals withstand the highest pressure of our buffering seals.

For use in air-powered cylinders, these seals prevent the piston from slamming against the cylinder body to minimize wear and noise.

A square O-ring prevents these piston seals from rocking in the groove.

Rated for pressure up to 10,000 psi, these seals withstand the highest pressure of our piston seals.

These rod wipers are also known as U-type wipers.

These wipers seal against the cylinder housing to prevent contaminants from entering between the outside edge and the housing.

These compressors have a spring clutch that allows incremental sizing adjustments for a secure fit. Use them to ensure smooth insertion of your piston into a cylinder.

Also known as a wrinkle-band compressor, this tool has fewer points of contact than other compressors for less friction.

Reduce the risk of distorting and breaking piston rings during installation and removal.

Cut this stock to make wear rings that fit any rod or bore diameter.

Super thin and flexible, these cotton yarn seals fit into tight spaces, such as in faucets.

The Inconel-wire reinforcement in these expanded-graphite yarn seals ensures they keep their shape longer than the High-Flexibility Steam-Resistant Packing Seals. Use them for steam applications in valves.

PTFE has excellent chemical resistance and withstands a wide temperature range of -110° F to 500° F.

Our most compressible packing seals, these require less pressure than any other to make an effective seal. They’re made of lubricated PTFE-impregnated aramid fiber and are for use in pumps.

Made of FDA-listed material for use with food and beverage, these PTFE seals are lubricated with mineral oil. Use them in pumps.

Synthetic yarn that’s comparable in strength to aramid is combined with graphite for soft seals that dissipate heat away from the shaft to extend the life of pumps.

These lubricated PTFE fiber seals stand up to most chemicals. Use them in pumps and valves.

The most abrasion resistant of all our packing seals, these are made of PTFE-impregnated aramid fiber that has been saturated in a lubricant. They are for use in pumps.

Fill irregularities in valve stem with these soft PTFE seals.

Install between layers of packing seals to ensure lubricants are distributed evenly. These lubricating rings are also known as lantern rings.