With excellent resistance to corrosive chemicals and salt water, these epoxies work in tough conditions. Epoxies are the strongest structural adhesives. Choose an adhesive that hardens quickly for fast repairs, or one that hardens slowly to allow more time for positioning.

The size listed is the combined total of the two parts. Use cartridges with a dispensing gun and mixer nozzle to simultaneously mix and dispense adhesives.

Fasten hard-to-bond plastics, such as polypropylene and polyethylene, with these adhesives. Acrylics bond to the widest range of materials, especially plastics, and require the least amount of surface preparation.

The size listed is the combined total of the two parts. Use a dispensing gun and mixer nozzle to simultaneously mix and dispense adhesives.

DP8005 contains 0.008" glass beads to prevent adhesive from squeezing out during clamping and give a consistent bond thickness.

DP8010 and DP8010NS are moisture and corrosion resistant. DP8010NS is nonsagging, so it won't drip from vertical or overhead surfaces.

Acrylics bond to the widest range of materials, especially plastics, and require the least amount of surface preparation.

The size listed is the combined total of the two parts. Use a dispensing gun and mixer nozzle to simultaneously mix and dispense adhesives.

H8000 and H8100 maintain their impact resistance at cold temperatures.

Toughened adhesives are blended with rubber particles for better impact resistance than standard acrylics. They form resilient bonds. Acrylics bond to the widest range of materials, especially plastics, and require the least amount of surface preparation.

The size listed is the combined total of the two parts. Use cartridges with a dispensing gun and mixer nozzle to simultaneously mix and dispense adhesives.

MA310 bonds dissimilar materials.

Apply this glue like tape for a no-mess alternative to liquid adhesives, hot melts, and staples. Also known as adhesive transfer tape, these rolls have a thin film of pressure-sensitive glue on a peel-away liner. They are thinner and more conformable than tape with adhesive on both sides.

9482PC and 9485PC bond well to slippery plastics. They're reinforced with fiber for stability.

Apply these adhesives on two surfaces, air dry, and then bring together to bond.

4693 works on hard-to-bond plastics, such as polypropylene and polyethylene.

Adhesives that cannot be sold to the regions listed exceed local regulatory limits on VOCs (volatile organic compounds).

Spray a thin, uniform coat of adhesive on one or both surfaces, air dry, and then bring together to form strong bonds.

Form bonds with twice the strength of our other spray adhesives. Spray a thin, uniform coat of adhesive on one or both surfaces, air dry, and then bring together to adhere.

Adhesives that cannot be sold to California exceed local regulatory limits on VOCs (volatile organic compounds).

For easy positioning, this adhesive remains tacky for hours. Once items are in place, apply pressure to create a permanent bond. The blue color shows where adhesive has been applied. They cannot be sold to California due to local regulatory limits on VOCs (volatile organic compounds).

These spray glues adhere quickly. Spray a thin, uniform coating on one surface, air dry, and then bring together to bond. They cannot be sold to California due to local regulatory limits on VOCs (volatile organic compounds).

Improve instant-bond adhesive performance on hard-to-bond slippery plastics. These primers cannot be sold to the regions listed because they exceed local regulatory limits on VOCs (volatile organic compounds).

Primers in brush-top bottles also include a spray head for easy dispensing.

These structural sealants combine the mechanical strength of an adhesive with excellent sealing properties and high flexibility. They’re non-sagging, so they won't drip from vertical and overhead surfaces.

Elongation and joint compression/expansion tolerance indicate flexibility—the higher the values are, the more joint movement sealants can sustain. For joints between dissimilar materials and in environments with wide temperature fluctuation, choose a sealant with a higher elongation or joint compression/expansion tolerance. For high-wear applications, choose a harder sealant for the most abrasion resistance.

Impervious to the swelling effects of oils, fuels, and solvents, use this high-strength silicone sealant to assemble and repair fuel systems and tanks. Silicone forms a tough, rubbery, UV-resistant seal that remains flexible over time. It's non-sagging, so it won't drip from vertical and overhead surfaces. Also known as RTV (room-temperature vulcanizing).

Elongation and joint expansion/compression tolerance indicate flexibility—the higher the values are, the more joint movement sealants can sustain. This sealant is best suited to joints between similar materials that aren't exposed to wide temperature fluctuation.

Often used in high-vibration applications that could cause standard thread sealants to fail, these never fully harden and remain pliable enough to self-heal and stop leaks before they start. They have low locking strength, so they can be adjusted without tools.

To adhere to safety standards for drinking water systems, use sealants that meet NSF/ANSI 61.

Sealants that cannot be sold to the regions listed exceed local regulatory limits on VOCs (volatile organic compounds).

These thread sealants are anaerobic, so they don’t begin to harden until coated surfaces are threaded together, blocking exposure to air.

Sealants with medium locking strength prevent threads from loosening due to vibration and shock. They require a hand tool to unthread.

To adhere to safety standards for drinking water systems, use sealants that meet NSF/ANSI 61.

Formulated for high lubricity, these sealants allow easy assembly of finely threaded hydraulic and compressed air system components. They're also free of fillers that could contaminate system media. These sealants are anaerobic, so they don’t begin to harden until coated surfaces are threaded together, blocking exposure to air.

Sealants with medium locking strength prevent threads from loosening due to vibration and shock. They require a hand tool to unthread.

Seal joints and gaps in concrete. These sealants are non-sagging, so they won't drip from vertical and overhead surfaces.

Silicone sealant is RTV (room-temperature vulcanizing).

Elongation and joint compression/expansion tolerance indicate flexibility—the higher the values are, the more joint movement sealants can sustain. These sealants are best suited to joints between similar materials that aren't exposed to wide temperature fluctuation.

Seal concrete joints in high-traffic areas—these sealants stand up to heavy wear and tear, such as steel wheel traffic. They're non-sagging, so they won't drip from vertical and overhead surfaces. Made from silicone, sealants are RTV (room-temperature vulcanizing).

Elongation and joint compression/expansion tolerance indicate flexibility—the higher the values are, the more joint movement sealants can sustain. These sealants are best suited to joints between similar materials that aren't exposed to wide temperature fluctuation. For high-wear applications, choose a harder sealant for the most abrasion resistance.

Keep out the elements by sealing roof joints. These sealants are non-sagging, so they won't drip from vertical and overhead surfaces. They are good for use in environments with wide temperature fluctuation.

Also known as sloshing compounds, these two-part epoxies bond to rough and rusty surfaces in fuel tanks to repair leaks and prevent further corrosion. They withstand permanent immersion in fuel, oil, and harsh solvents. Use them with metal, plastic, and fiberglass tanks. Mix the smaller can with the bigger one and pour into your fuel tank. Rotate the tank to coat the interior and dump out any excess. Allow to cure overnight. Size listed is the combined total of the two parts.

1.5-pint container can treat a 10-gallon fuel tank. 3-pint container can treat a 20-gallon fuel tank.

Repair small leaks and cracks in coolant systems for commercial vehicles and industrial equipment. These surface fillers meet ASTM D3147 for their ability to stop leaks in engine cooling systems. Pour them into your coolant to fix both internal and external leaks. They contain ceramic microfibers and copper particles to create a permanent seal. They’re compatible with antifreeze and other coolant system additives.