Pick up objects on the ground, grab items on high shelves, and reach into deep tanks.

An LED lights the wire jaws and the shaft bends to reach objects in awkward spaces.

Thin wire jaws grasp small or oddly shaped objects.

LEDs light the magnetized tip and the shaft bends and stays in position to reach objects in awkward spaces.

Bend the shaft to reach objects in awkward spaces.

A fluorescent orange handle makes these retrievers stand out, so they’re less likely to be misplaced.

An extra-long shaft enables access to material in hard-to-reach areas. These retrievers can pick up heavier objects than our other magnetic retrievers.

The head pivots, so you can pick up screws, nuts, bolts, and other small steel objects from any angle.

LEDs light the magnetized tip for picking up small steel objects in dark areas. Pivot the head to access material from any angle.

Also known as rescue hooks, these retrievers are often used to pull an injured worker away from electrical hazards without risking the safety of other workers. They have a fiberglass handle and insulated hook to protect against accidental contact with live electrical circuits. The handle is tested to meet the requirements of ASTM F711.

Slip the cable over an object and it locks in place once tightened.

The pointed tip with curved hook is good for holding and pulling cylindrical material.

When there isn't clearance to use standard-grip locking pliers, the angled handle on these tools gives you access. Lock the jaws around a workpiece and these pliers stay clamped in place.

Attach your locking pliers to a slide hammer to pull stubborn objects.

Choose a stainless steel tool for environments where moisture and other contaminants are present. These pliers resist corrosion that can hinder joint movement, but the jaws will wear more quickly than a steel tool. Lock the jaws around a workpiece and they stay clamped in a vise-like grip.

Curved jaws grip bolt heads and nuts with rounded corners. These pliers lock in a vise-like grip and stay clamped in place, leaving your hands free.

Lock the jaws in a vise-like grip around a workpiece and these pliers stay clamped in place to leave your hands free.

Squeeze the handles and the jaws automatically adjust to fit a workpiece and lock in place.

Removable and reusable, these rubber covers fit most slip-joint pliers and resist most oils and chemicals.

Prevent damage to your workpieces with pliers that have nonmarring jaws. Adjust the pivot point to switch between two different jaw opening sizes.

Made of aluminum-bronze that is FM approved, these pliers satisfy OSHA requirements that specify nonsparking tools for locations where flammable vapors and combustible residues are present.

Insulated grips protect against accidental contact with live electrical circuits. These pliers are tested to 1,000 volts to meet IEC 60900 and ASTM F1505.

Two curved openings on the jaws grip multiple sizes of round stock, tubing, and pipe.

Tips almost twice as wide as those of standard long-nose pliers give you a better grip on your work. These are also known as duckbill and flat-nose pliers.

Prevent damage to your workpieces with pliers that have nonmarring jaws.

With thinner tips than standard long-nose pliers, these tools fit into tight spaces.

With thinner tips than standard long-nose pliers, these stainless steel tools fit into tight spaces and are good for environments where moisture and other contaminants are present. They resist corrosion that can hinder joint movement, but the jaws will wear more quickly than a steel tool.

Secure a lanyard to the ring on the handle to prevent dropping your pliers when working at height.

Also known as duckbill and flat-nose pliers, the extra-wide tips give you better grip on your work. These stainless steel tools are good for environments where moisture and other contaminants are present. They resist corrosion that can hinder joint movement, but the jaws will wear more quickly than a steel tool.

Made entirely of plastic, these pliers eliminate the potential for an arc flash or short circuit that can occur when using conventional insulated tools with metal components. They are tested to 1,000 volts to meet IEC 60900 and ASTM F1505.

Extra-wide tips give you a better grip on your work, and smooth, consistent movement ensures precision. These tools have a slip-resistant ultra grip that’s shaped to fit comfortably in your hand and reduce strain in repetitive tasks. They are also known as miniature and electronics pliers.

Replaceable rubber jaw pads protect surfaces from damage. These tools grip round objects and won't mar delicate materials, such as glass and ceramic.

Lock the jaws in a vise-like grip around a workpiece and these assorted pliers stay clamped in place to leave your hands free.

More jaw positions than standard adjustable pliers enable fine adjustment and a firm grip. Push and hold the button to adjust the jaws, and then release the button to lock them in place.

Colorful plastic grips make these assorted pliers stand out, so they’re less likely to be misplaced.

Smooth, consistent movement ensures precision. These assorted pliers have slip-resistant ultra grips that are shaped to fit comfortably in your hand and reduce strain in repetitive tasks. They are also known as miniature and electronics pliers.

Choose these stainless steel pliers for environments where moisture and other contaminants are present. They resist corrosion that can hinder joint movement, but the jaws will wear more quickly than a steel tool.

Clamp down on nonreinforced hose and tube to squeeze it shut, eliminating the need to drain the hose when working on pumps, heating and cooling systems, and fuel lines. Squeeze the handles to lock the jaws and these pliers stay in place.

Also known as lineman’s and combination pliers, use these tools to pull, bend, and cut wire.

When there isn't clearance to use standard-grip pliers, the angled head on these tools gives you access. Also known as lineman’s and combination pliers, use them to pull, bend, and cut wire.

Deep serrations provide the firm grip necessary for pulling rebar tie wire, and the hook-shaped handle end keeps your hand from slipping off. Also known ironworkers’ pliers, these tools also bend and cut wire.

Made of aluminum-bronze that is FM approved, these pliers satisfy OSHA requirements that specify nonsparking tools for locations where flammable vapors and combustible residues are present. Use them to pull, bend, and cut wire.

Secure a lanyard to the ring on the handle to prevent dropping your pliers when working at height. Use these tools to pull, bend, and cut wire.

Squeeze the handles to open the jaws; release to snap them closed. Once closed, they stay clamped in place to leave your hands free. These pliers reach around closely spaced components and other obstructions.

Smooth, consistent movement ensures precision. These tools have a slip-resistant ultra grip that’s shaped to fit comfortably in your hand and reduce strain in repetitive tasks. They are also known as miniature and electronics pliers and shaped to reach around closely spaced components and other obstructions.

The jaws are made of brass, which won't damage steel workpieces. These pliers are shaped to reach around closely spaced components and other obstructions.

Insulated grips protect against accidental contact with live electrical circuits. These pliers are tested to 1,000 volts to meet IEC 60900. They are shaped to reach around closely spaced components and other obstructions.

Made of aluminum-bronze that is FM approved, these pliers satisfy OSHA requirements that specify nonsparking tools for locations where flammable vapors and combustible residues are present.

A slim head and long, narrow jaws fit into tight spaces.

Slide the pivot point of the jaws to a range of positions and squeeze the handles to grip.

You don't have to move the pivot point on these pliers—squeeze the handles and the jaws adjust to fit your workpiece.

The grips drain static from your application, preventing buildup from electrostatic discharge (ESD) that can damage sensitive equipment.

More jaw positions than standard adjustable pliers enable fine adjustment and a firm grip. Push and hold the button to adjust the jaws, and then release the button to lock them in place.

The smallest round-nose pliers we offer allow you to bend and loop wire in the smallest spaces, including under a microscope.

Designed for looping and bending wire, these steel tools are also known as round-nose pliers.

Made of beryllium copper that is FM approved, these pliers satisfy OSHA requirements that specify nonsparking tools for locations where flammable vapors and combustible residues are present. Also known as round-nose pliers, use for looping and bending wire.

These general purpose tweezers grip a variety of objects.

Sets include assorted tweezers with each style a different color for easy identification.

Extra-long tips provide access to material in hard-to-reach areas.

These assorted tweezers hold small parts without the need to apply pressure. Squeeze to open the tips and release to close them.

Hold small parts without the need to apply pressure. Squeeze these tweezers to open the tips and release to close them.

A PTFE coating on the tips prevents material from sticking to these tweezers.

The cushioned grips insulate against heat.

Prevent buildup from electrostatic discharge (ESD) that can damage sensitive equipment. The cushioned grips drain static from your application and provide comfort and heat protection.

Wide, flat tips ensure a good grip on thin sheets and labels.

These premium tweezers are Swiss made to tight tolerances for the perfect tip alignment required for work under magnification.

Solder won’t stick to these tweezers. Made of titanium for high strength and durability, they are nonmagnetic and have excellent corrosion resistance. These premium tools are Swiss made to tight tolerances for the perfect tip alignment required for work under magnification.

These assorted tweezers have tips that can be replaced when they become worn. Tips are carbon fiber, which insulates against heat and won’t nick or scratch components.

Designed for placing chips and electronic components on circuit boards, these tweezers have rectangular-shaped tips that are angled to reach over and around obstructions. They are also known as SMD (surface-mount device) tweezers.

Remove chips and other delicate components from circuit boards.

Sets include an assortment of premium tweezers that are Swiss made to tight tolerances for the perfect tip alignment required for work under magnification.

Get a firm grip on beakers and other containers in the curved jaws. You can also use the tips of these tongs to pick up small objects.

A heavy duty steel construction and long handle allow you to grip hot material in furnaces and forging and heat-treating applications.

Keep hands away from machinery—use these lightweight tools to pick up and hold parts. The pliers-style handles provide more comfort and control than standard tongs.