Penetrate gaskets, sealed bearings, and joints to deliver grease to precise locations.

Penetrate gaskets, sealed bearings, and joints to deliver grease to precise locations.

These flexible nozzles come with a dispensing tip and have threads on one end for connecting to a grease gun.

These rigid nozzles come with a dispensing tip and have threads on one end for connecting to a grease gun.

With threads on both ends, these rigid nozzles connect grease guns to dispensing tips.

Convert dispensing tips with male threads into quick-disconnect couplings.

These flexible extensions have a quick-disconnect fitting that snaps into your dispensing tip, so you can lubricate grease fittings that are hard to reach.

Sets include dispensing tips for grease fittings and bare lubrication points.

Dispense small amounts of grease with one of these compact guns.

Because of their one-hand operation, pistol-grip grease guns are easier to use for adding grease to hard-to-reach places than lever-grip guns.

Dispensing more grease per pump than pistol-grip guns, lever-grip guns are better for applications that require high grease output.

These guns deliver twice as much grease per stroke than standard lever-grip guns.

Dispense small amounts of grease with this compact gun.

Switch between high-pressure and low-pressure settings. Use high pressure to dispense thicker grease or to force grease through clogged fittings. Use low pressure for high-volume dispensing.

Use compressed air to dispense grease.

Deliver small amounts of grease with only a light push against the lubrication point.

Replace the dispensing tip on your filler pump.

Turn the metering pin to adjust flow rate.

Tighten the cover to dispense grease.

Useful in remote areas without access to air or electrical power.

Apply lubricant to gear racks with a 14 1/2° pressure angle and a pitch of 16.

Switch between high-pressure and low-pressure settings. Use high pressure to dispense thicker grease or to force grease through clogged fittings. Use low pressure for high-volume dispensing.

Connect these guns to container-mount dispensers for controlled dispensing.

A display allows you to monitor how much grease is dispensed.

Choose from pumps that dispense with a set interval. Turn the dial to adjust the flow from 0.1 oz. to 0.2 oz. per cycle.

With a maximum flow of 0.005 oz. per cycle, these pumps deliver small, precise amounts of oil. Turn the dial to set the cycle interval.

Ready to connect to your air system, these complete systems include a timer and a reservoir.

Connect these modular pumps to a reservoir and a solenoid valve to automate the flow of oil.

A sealed design prevents contamination in dirty and dusty environments.

Customize these dispensers to serve up to 24 lubrication points from a single location.

Control the flow of oil to a single lubrication point.

A sealed design prevents contamination in dirty and dusty environments.

As chain, gears, and conveyors move, these brushes rotate to apply lubricant.

Mount these reservoirs directly to your machine, or use them with a flow-adjustment valve and brush to create a dispenser.

A sealed design prevents contamination in dirty and dusty environments. Install a line between the reservoir's pressure port and the lubricated equipment to balance pressure.

Connect these brushes to oil reservoirs and flow adjustment valves to lubricate chain, gears, and conveyors.

Use this dispenser to brush oil on chain, gears, and conveyors. Often used to replenish lubricant after washdowns.

Flip the lever to start and stop flow.

Equipped with a flowmeter/totalizer, this dispenser displays both the flow rate and the cumulative flow volume of the oil dispensed.

Connect these dispensing stations to your bulk oil container to easily fill hand-held dispensers.

Pull the trigger on these oilers for easier one-hand operation than standard hand-held oil dispensers.

These dispensers have an opening for filling without removing the nozzle.

Deliver a mist of oil using shop air.

Press the lever to stop coolant mist and start a high-velocity air stream to remove dust and shavings.

These dispensers have a reservoir for recirculating coolant.

Replace messy mist coolant dispensers—these convert compressed air into a stream of cold air. They can be used in applications where liquid coolant can't.

Build a custom 1/2" system to deliver coolant, cutting oil, water, or air in any direction.

Kits contain lengths of hose, nozzles, valves, and caps.

Use with Snap-Loc hose to assemble and disassemble components.

Use with Loc-Line hose to assemble and disassemble components.

Kit contains lengths of hose, nozzles, connectors, and assembly pliers.

This hose is made of steel.

These nozzles handle coolant pressure up to 150 psi.

For use in the highest pressure coolant lines, these nozzles are rated for at least 1,000 psi.

For high-pressure coolant lines, these nozzles withstand pressure up to 500 psi.

Connect these needles to adhesive cartridges, grease guns, and other dispensers with a threaded connection.

Thanks to the nickel-plated brass base on these needles, they can be cleaned, washed, boiled, or sterilized.

The nonstick surface is good for liquids that tend to clog, such as instant-bonding adhesives.

Often used to spread adhesives when attached to syringes and dispensers with a luer lock connection.

Attach a needle with a luer lock connection to dispense contents.

Designed for dispensing tiny quantities, these glass syringes are often used in gas chromatography applications. Attach a needle with a luer lock connection to dispense contents.

Often used in chromatography applications, these filters attach to any syringe with a luer lock connection to filter out contaminants both when drawing in and dispensing.

Unlike standard spray bottles, these dispense oil and other high-viscosity liquids without clogging.

Release a fine mist spray similar to an aerosol without propellants or pressure.

Spray at any angle—even upside down.

These spray bottles resist harsh chemicals and solvents.

Access tight spaces with the 36" long tube that extends from these spray bottles.

Assortments contain straight, 45° elbow, and 90° elbow fittings.

Keep thin grease from leaking out—the check valve on these fittings has a Buna-N seat that creates a tighter seal than check valves on other grease fittings.

Often used on earth movers, mining equipment, and other heavy machinery, these fittings have a T-shaped top that holds the dispensing tip in place so it won't pop off when adding grease.

Ensure a secure fit in unthreaded holes—these fittings cut threads as they’re installed. They're also known as hydraulic grease fittings.

Ensure a secure fit in unthreaded holes—these fittings cut threads as they’re installed. Use these fittings in tight spaces where protruding fittings won't work.

When the size or thread type of a fitting doesn't match an existing opening, use these adapters to make the connection.

Fill these tools with light oil, then tap with a hammer to open clogged fittings.

Tap these tools once or twice with a hammer to install fittings.

Keep standard grease fittings free of dirt and moisture.

Install these fittings into threaded holes.