Inject lubricant into motors, bearings, engine blocks, and all kinds of machinery.

Keep thin grease from leaking out—the check valve on these fittings has a Buna-N seat that creates a tighter seal than check valves on other grease fittings.

Often used on earth movers, mining equipment, and other heavy machinery, these fittings have a T-shaped top that holds the dispensing tip in place so it won't pop off when adding grease.

Use these fittings in tight spaces where protruding fittings won't work.

Drive these fittings into unthreaded holes. They're also known as hydraulic grease fittings.

Ensure a secure fit in unthreaded holes—these fittings cut threads as they’re installed. Use these fittings in tight spaces where protruding fittings won't work.

Access difficult-to-reach lubrication points from up to 10 ft. away.

Tap these tools once or twice with a hammer to install fittings.

Remove worn fittings and repair threaded holes.

Install these fittings into threaded holes.

Because of their one-hand operation, pistol-grip grease guns are easier to use for adding grease to hard-to-reach places than lever-grip guns.

Dispense small amounts of grease with one of these compact guns.

Switch between high-pressure and low-pressure settings. Use high pressure to dispense thicker grease or to force grease through clogged fittings. Use low pressure for high-volume dispensing.

Switch between high-pressure and low-pressure settings. Use high pressure to dispense thicker grease or to force grease through clogged fittings. Use low pressure for high-volume dispensing.

Dispense small amounts of grease with this compact gun.

Designed to lubricate linear motion components, such as slide bearings, guides, and ball screws, these guns work exclusively with THK grease cartridges and fittings.

Be sure you’re using the right grease—this gun has a clear barrel for identification at a glance.

This gun comes filled with 2 oz. of lithium-thickened grease.

Dispense from grease guns into grease fittings and bare lubrication points.

Dispense from grease guns into grease fittings and bare lubrication points.

These rigid tip adapters penetrate gaskets, sealed bearings, and joints to deliver grease to precise locations.

With threads on both ends, these rigid nozzles connect grease guns to dispensing tips.

Slide the metal sleeve up to the tip for rigidity. Slide it back down to expose the flexible nozzle.

Penetrate gaskets, sealed bearings, and joints to deliver grease to precise locations.

These flexible extensions have a quick-disconnect fitting that snaps into your dispensing tip, so you can lubricate grease fittings that are hard to reach.

Convert dispensing tips with male threads into quick-disconnect couplings.

Attach these nipples to guns to load grease from bulk filler pumps.

Spring pressure ensures a constant flow of grease.

Tighten the cover to dispense grease.

Connect these modular pumps to your air system and add a solenoid valve to automate the flow of grease.

Apply lubricant to gear racks with a 14 1/2° pressure angle and a pitch of 16.

A display allows you to monitor how much grease is dispensed.

Increase the pressure of your grease system when necessary to dispense thick grease and force grease through clogged fittings.

This dispenser delivers over three times more grease per stroke than our dual-output dispensers.

Move grease-dispensing guns in any direction without kinking the outlet hose.

These dispensers have an opening for filling without removing the nozzle.

A needle dispensing tip provides fine control for lubricating small parts.

Clamp this applicator around control cables to lubricate them with minimal mess.

Use suction to remove old lubricant from gear boxes and transmissions.

A sealed design prevents contamination in dirty and dusty environments.

A solenoid automatically starts and stops flow to a single lubrication point to dispense lubricant while equipment is running.

Deliver an equal amount of oil to multiple lubrication points at once.

A sealed design prevents contamination in dirty and dusty environments.

Connect these brushes to oil reservoirs and flow adjustment valves to lubricate chain, gears, and conveyors.

Customize these dispensers to serve up to 24 lubrication points from a single location.

As chain, gears, and conveyors move, these brushes rotate to apply lubricant.

A sealed design prevents contamination in dirty and dusty environments. Install a line between the reservoir's pressure port and the lubricated equipment to balance pressure.

Flip the lever to start and stop flow.

A solenoid automatically starts and stops flow to dispense lubricant while equipment is running.

As chain, gears, and conveyors move, these brushes rotate to apply lubricant.

Set the cycle interval as well as the dispensing duration. This pump has a maximum flow of 0.1 oz. per second.

Choose from pumps that dispense with a set interval. Turn the dial to adjust the flow from 0.1 oz. to 0.2 oz. per cycle.

Air pressurizes the oil in the reservoir and atomizes the spray. Add a spray valve to direct the flow of oil.

Dispense a fixed amount of oil by pumping the handle.

Driven by an air-powered pump, this dispenser comes with an adapter to mount through a bung opening on a drum.

Measure oil as it's dispensed.

These manual dispensers are more portable than air-powered dispensers.

For use in the highest pressure coolant lines, these nozzles are rated for at least 1,000 psi.

These nozzles handle coolant pressure up to 150 psi.

These nozzles handle coolant pressure up to 150 psi.

Kits contain lengths of hose, nozzles, valves, and caps.

Kit contains lengths of hose, nozzles, connectors, and assembly pliers.

Build a custom 1/2" system to deliver coolant, cutting oil, water, or air in any direction.

Use with Snap-Loc hose to assemble and disassemble components.

Swivel the ball-socket connections to position these arms and then lock them in place.

These dispensers have a reservoir and controls for coolant flow.

Press the lever to stop coolant mist and start a high-velocity air stream to remove dust and shavings.

Draw coolant from your existing tank.

Connect these needles to adhesive cartridges, grease guns, and other dispensers with a threaded connection.

The nonstick surface is good for liquids that tend to clog, such as instant-bonding adhesives.

Use these components to create an air-powered dispensing system. A foot pedal controls the amount released.

A curved plastic tip fits into bearing seals, narrow holes in housings, and around small parts in 3D printers and other machinery. Use these syringes to control the direction of flow so you don't make a mess.

Use these syringes with an air-powered dispenser to make repetitive dispensing easier on your hands.

Spray liquids with these fillable bottles—the head twists on and off to make filling easy.

Protect against excess vacuum and pressure in cylinders, gear boxes, enclosures, manifolds, and tanks.