Designed to stand up to heavy use, these wheels remove more material than our general purpose grinding wheels.

A more durable abrasive allows these wheels to remove more material and last longer than Norton General Purpose Grinding Wheels. They are also known as Type 1 wheels and straight wheels.

Unlike aluminum oxide wheels, these silicon carbide wheels won’t clog when grinding soft metals.

Typically used with cylindrical, surface, and ID grinders, these wheels are specially designed to grind the inside diameter of workpieces.

The flexible backing on these wheels conforms to curved and rough surfaces.

The abrasive grains in these bits are blended with rubber, which cushions during grinding to produce a smoother surface texture than other bits with similar grits.

Use bits in any drill chuck that accepts a 1/4" hex shank.

Each set contains a selection of our most popular grinding bits.

Overlapping abrasive flaps bonded to a backing plate provide consistent material removal and even finishes.

These discs have a harder abrasive than standard flap sanding discs.

The flaps alternate between an abrasive to remove material and a lubricant that minimizes heat to reduce discoloration of the work surface.

These discs have a harder abrasive than standard flap sanding discs for corners.

With more flaps than standard discs, these last 30-40% longer.

The flaps have an abrasive to remove material and a lubricant that minimizes heat to reduce discoloration of the work surface.

The flaps wrap around the outer edge of these discs to sand welds at right angles.

With more flaps than standard discs, these last 30-40% longer.

Set at an angle and widely spaced, the flaps reach into corners.

These discs have a harder abrasive than standard quick-change discs.

These discs have a harder abrasive than standard flexible-edge quick-change discs.

The premium abrasive stays sharp longer.

A special fastener on the back of these discs allows you to easily swap one disc for another.

These discs have a long-lasting diamond abrasive.

The premium abrasive stays sharp longer.

Holes in the disc let you see the surface you’re sanding.

Fit these discs over your tool’s arbor to sand stainless steel and hard metals.

A coating prevents dust and debris from building up on the abrasive surface.

Fit these discs over your tool's arbor to sand aluminum, soft metals, and nonmetals.

A coating prevents dust and debris from building up on the abrasive surface.

Holes allow dust removal when used with a vacuum sander.

Also known as Type 27, raised-hub, and depressed-center cutoff wheels, these wheels outperform Type 1 wheels when making flush cuts in metal.

With an X-shaped arbor hole, these wheels quickly and safely click into X-lock grinders without wrenches or flange nuts.

Made of premium grade abrasives, these wheels are strong and thick for making notches in aluminum, iron, stainless steel, and steel.

Also known as Type 27, raised-hub, and depressed-center cutoff wheels, these wheels outperform Type 1 wheels when making flush cuts.

Also known as Type 27, raised-hub, and depressed-center cutoff wheels, these wheels outperform Type 1 wheels when making flush cuts.

Made of ceramic alumina or a combination of ceramic alumina and zirconia alumina, these wheels last up to ten times longer than standard cutoff wheels when cutting hard metal such as Inconel, Hastelloy, and tool steel.

Run these high-density aluminum oxide wheels at higher speeds than standard cutoff wheels to make quick cuts in aluminum, iron, stainless steel, and steel.

Premium-grade abrasive materials and two layers of fiberglass mesh reinforcement give these wheels a longer life than standard cutoff wheels when cutting metal such as iron, stainless steel, and steel.

The combination of ceramic alumina and zirconia alumina in these wheels lasts up to ten times longer than aluminum oxide when cutting hard metal such as Inconel, Hastelloy, and tool steel.

Use these clog-resistant zirconia alumina wheels to make quick cuts in soft metal such as aluminum, brass, and copper.

An extra-fine layer of fiberglass mesh reinforcement allows these wheels to make smoother cuts than standard bench-grinder cutoff wheels when cutting metal such as aluminum, iron, stainless steel, and steel.

Use these wheels to cut through metal such as aluminum, iron, stainless steel, and steel.

Make fast, burr-free cuts in stainless steel with these premium aluminum oxide wheels.