Maintain a secure hold on uneven or irregularly shaped parts by clamping against these serrated grippers.

Screw in from the top to adjust height or mount from the bottom with a hex key to set the gripping surface flush with the work surface.

Clamp against these grippers for a secure hold on workpiece edges.

Pick up objects on the ground, grab items on high shelves, and reach into deep tanks.

An LED lights the wire jaws and the shaft bends to reach objects in awkward spaces.

Thin wire jaws grasp small or oddly shaped objects.

An extra-long shaft enables access to material in hard-to-reach areas. These retrievers can pick up heavier objects than our other magnetic retrievers.

LEDs light the magnetized tip for picking up screws, nuts, and other small steel objects in dark areas.

An extra-long shaft and pivoting head lets you access hard-to-reach material from almost any angle.

LEDs light the magnetized tip for picking up small steel objects in dark areas. Pivot the head to access material from any angle.

LEDs light the magnetized tip and the shaft bends and stays in position to reach objects in awkward spaces.

Protect against accidental contact with live electrical circuits. These insulated retrievers are tested to 1,000 volts to meet IEC 60900 and ASTM F1505. The shaft bends and stays in position to reach objects in awkward spaces.

Also known as rescue hooks, these retrievers are often used to pull an injured worker away from electrical hazards without risking the safety of other workers. They have a fiberglass handle and insulated hook to protect against accidental contact with live electrical circuits. The handle is tested to meet the requirements of ASTM F711.

Spear litter with the sharp point.

Attach to the end of a screw or threaded stud—the serrated face swivels to grip uneven and angled surfaces. Also known as toggle and swivel-foot pads.

Lock the jaws in a vise-like grip around a workpiece and these pliers stay clamped in place to leave your hands free.

Choose a stainless steel tool for environments where moisture and other contaminants are present. These pliers resist corrosion that can hinder joint movement, but the jaws will wear more quickly than a steel tool. Lock the jaws around a workpiece and they stay clamped in a vise-like grip.

Secure these holders to a table or benchtop and slide in up to three pairs of locking pliers to create a hands-free way to hold your work.

Long jaws reach workpieces in recessed areas. These pliers lock in a vise-like grip around a workpiece and stay clamped in place to leave your hands free.

Curved jaws grip bolt heads and nuts with rounded corners. These pliers lock in a vise-like grip and stay clamped in place, leaving your hands free.

Change out worn or broken springs in the handle of your locking pliers.

Tips almost twice as wide as those of standard long-nose pliers give you a better grip on your work. These are also known as duckbill and flat-nose pliers.

Extra-long handles enable access in hard-to-reach areas.

Additional features, such as wire terminal crimpers and wire stripping holes, enable you to perform a variety of electrical wiring and installation work with a single tool.

With thinner tips than standard long-nose pliers, these tools fit into tight spaces.

With thinner tips than standard long-nose pliers, these stainless steel tools fit into tight spaces and are good for environments where moisture and other contaminants are present. They resist corrosion that can hinder joint movement, but the jaws will wear more quickly than a steel tool.

Made of materials that are FM approved, these pliers satisfy OSHA requirements that specify nonsparking tools for locations where flammable vapors and combustible residues are present.

Secure a lanyard to the ring on the handle to prevent dropping your pliers when working at height.

The grips drain static away from your application, preventing buildup from electrostatic discharge (ESD) that can damage sensitive equipment.

Smooth, consistent movement ensures precision. These tools have a slip-resistant ultra grip that’s shaped to fit comfortably in your hand and reduce strain in repetitive tasks. They are also known as miniature and electronics pliers.

Get the best possible grip on round objects, such as oil filters, connectors, and PVC pipe. These pliers have curved jaws and a slip joint to switch between two opening sizes. They're also known as cannon plug pliers.

Extra-long handles enable access to hard-to-reach areas. These pliers are shaped to reach around closely spaced components and other obstructions.

Choose a stainless steel tool for environments where moisture and other contaminants are present. These pliers resist corrosion that can hinder joint movement, but the jaws will wear more quickly than a steel tool. They are shaped to reach around closely spaced components and other obstructions

Insulated grips protect against accidental contact with live electrical circuits. These pliers are tested to 1,000 volts to meet IEC 60900. They are shaped to reach around closely spaced components and other obstructions.

Smooth, consistent movement ensures precision. These tools have a slip-resistant ultra grip that’s shaped to fit comfortably in your hand and reduce strain in repetitive tasks. They are also known as miniature and electronics pliers and shaped to reach around closely spaced components and other obstructions.

Lock the jaws in a vise-like grip around a workpiece and these assorted pliers stay clamped in place to leave your hands free.

Colorful plastic grips make these assorted pliers stand out, so they’re less likely to be misplaced.

Sets contain an assortment of pliers styles. These tools are steel.

Choose these tools when you need the gripping power of a pipe wrench with the adjustability of pliers. Slide the pivot point of the jaws to a range of positions.

More jaw positions than standard adjustable pliers enable fine adjustment and a firm grip. Push and hold the button to adjust the jaws, and then release the button to lock them in place.

Prevent damage to your workpieces with pliers that have nonmarring jaws. Adjust the pivot point to switch between two different jaw opening sizes.

Adjust the pivot point to switch between two different jaw opening sizes.

Colorful plastic grips make these pliers stand out, so they're less likely to be misplaced.

Insulated grips protect against accidental contact with live electrical circuits. These pliers are tested to 1,000 volts to meet IEC 60900 and ASTM F1505.

You don't have to move the pivot point on these pliers—squeeze the handles and the jaws adjust to fit your workpiece.

Slide the pivot point of the jaws to a range of positions and squeeze the handles to grip.

The bottom jaw is shorter than the top for a firm grip on the flats of bolt heads and nuts that have rounded corners.

Move the curved jaws to 15 positions for fine adjustment. These pliers have a bottom jaw that is shorter than the top for a firm grip on the flats of bolt heads and nuts that have rounded corners.

The grips drain static from your application, preventing buildup from electrostatic discharge (ESD) that can damage sensitive equipment.

Colorful plastic grips make these pliers stand out, so they're less likely to be misplaced.

Avoid the potential for an arc flash or short circuit that can occur when using conventional insulated tools with metal components. Completely metal-free, these pliers are plastic with ceramic cutting blades. They are tested to 1,000 volts to meet IEC 60900 and ASTM F1505. Use to pull, bend, and cut wire.

Extra-long handles enable access to hard-to-reach areas. Also known as lineman’s and combination pliers, use these tools to pull, bend, and cut wire.

Also known as lineman’s and combination pliers, use these tools to pull, bend, and cut wire.

Insulated grips protect against accidental contact with live electrical circuits. These pliers are tested to 1,000 volts to meet IEC 60900 and ASTM F1505. Use them to pull, bend, and cut wire.

Choose a stainless steel tool for environments where moisture and other contaminants are present. These pliers resist corrosion that can hinder joint movement, but the jaws will wear more quickly than a steel tool. Use them to pull, bend, and cut wire.

Smooth, consistent movement ensures precision. These tools have a slip-resistant ultra grip that’s shaped to fit comfortably in your hand and reduce strain in repetitive tasks. Also known as miniature and electronics pliers, they have a round nose for looping and bending wire.

Designed for looping and bending wire, these steel tools are also known as round-nose pliers.

Made of beryllium copper that is FM approved, these pliers satisfy OSHA requirements that specify nonsparking tools for locations where flammable vapors and combustible residues are present. Also known as round-nose pliers, use for looping and bending wire.

Clamp down on nonreinforced hose and tube to squeeze it shut, eliminating the need to drain the hose when working on pumps, heating and cooling systems, and fuel lines. Squeeze the handles to lock the jaws and these pliers stay in place.

Get a firm grip on beakers and other containers in the curved jaws. You can also use the tips of these tongs to pick up small objects.

Keep hands away from machinery—use these lightweight tools to pick up and hold parts. The pliers-style handles provide more comfort and control than standard tongs.

Extra-slim jaws taper to a narrow point that can reach into tight spots.

Hold small parts without the need to apply pressure. Squeeze these tweezers to open the tips and release to close them.

These general purpose tweezers grip a variety of objects.

Each style of tweezer is a different color for easy identification.

An LED lights the tips for picking up and positioning in dark areas.

Extra-long tips provide access to material in hard-to-reach areas.

Prevent buildup from electrostatic discharge (ESD) that can damage sensitive equipment. The cushioned grips drain static from your application and provide comfort and heat protection.

A PTFE coating on the tips prevents material from sticking to these tweezers.

Protect against accidental contact with live electrical circuits. These plastic-insulated tweezers are tested to 1,000 volts to meet IEC 60900 and ASTM F1505.

Toothed tips get a firm hold on thin and flexible material that is difficult to grip with standard tweezers, such as soft fabric and mesh.

These assorted tweezers have tips that can be replaced when they become worn. Tips are carbon fiber, which insulates against heat and won’t nick or scratch components.

Solder won’t stick to these tweezers. Made of titanium for high strength and durability, they are nonmagnetic and have excellent corrosion resistance. These premium tools are Swiss made to tight tolerances for the perfect tip alignment required for work under magnification.

Prevent buildup from electrostatic discharge (ESD) that can damage sensitive equipment. The cushioned grips drain static from your application. These premium tweezers are Swiss made to tight tolerances for the perfect tip alignment required for work under magnification.

Sets include an assortment of premium tweezers that are Swiss made to tight tolerances for the perfect tip alignment required for work under magnification.

Extend the life of these tweezers by replacing the tips when they become worn. Tips are carbon fiber, which insulates against heat and won’t nick or scratch components.

Keep your tweezers organized in these partitioned cases.

Jaw are serrated or grooved to firmly grip workpieces.

Squeeze the body to open the flat jaws; release to grip.

Sets include four vises with different opening sizes. A hollow body allows wires and rods to pass through.

Each end of the vise has a collet to hold a different tool—turn the collar to close the collets around them.

Press the rotating end cap on the handle with your palm to apply constant pressure while turning the body of the vise with your fingertips.

Notches on the jaws hold round material on its outside diameter.

The handles of these assorted picks have a magnet at the end to pick up small steel objects. Use to hold and position wire, springs, and other small parts.

Change tips to use a different size or style pick for holding and positioning wire, springs, and other small parts.

Reach around obstructions and into tight spaces with picks that have long, angled tips. Use these tools to hold, separate, and position wire, springs, and other small parts.

The assorted tools in these sets are used to hold, separate, and position wire, springs, and other small parts.

A different tip at each end allows you to install, extract, and position parts with one tool.

An insulated handle protects against accidental contact with live electrical circuits. These picks are tested to 1,000 volts to meet IEC 60900 and ASTM F1505.

Avoid nicking or scratching sensitive components. Also known as spudgers, these picks are good for adjusting small wires or separating press-fit plastic components.

Solder won’t stick to these assorted picks, which are used for positioning circuit board components.

Shaped for removing the seals around bearings, insert the tip of these tools behind the seal and pull. The curved head provides leverage to remove stuck and stubborn material.