Maintain a secure hold on uneven or irregularly shaped parts by clamping against these serrated grippers.

Clamp against these grippers for a secure hold on workpiece edges.

Bend the shaft to reach into awkward spaces and grab small parts in the wire jaws.

An extra-long shaft enables access to material in hard-to-reach areas. These retrievers can pick up heavier objects than our other magnetic retrievers.

Push the plunger to engage the magnet; release to disengage. These retrievers bend into position and stay in place.

Extra-long handles enable access in hard-to-reach areas.

Grip, bend, and twist wire and other small workpieces. Also known as needle-nose and chain-nose pliers, these tools have long, tapered jaws.

Prevent damage to your workpiece.

Tips almost twice as wide as those of standard long-nose pliers give you a better grip on your work. These are also known as duckbill and flat-nose pliers.

Secure a lanyard to the ring on the handle to prevent dropping your pliers when working at height.

Extra-wide tips give you a better grip on your work. These pliers have insulated grips that protect against accidental contact with live electrical circuits. They are tested to 1,000 volts to meet IEC 60900 and ASTM F1505.

Smooth, consistent movement ensures precision. These tools have a slip-resistant ultra grip that’s shaped to fit comfortably in your hand and reduce strain in repetitive tasks. They are also known as miniature and electronics pliers.

When there isn't clearance to use standard-grip locking pliers, the angled handle on these tools gives you access. Lock the jaws around a workpiece and these pliers stay clamped in place.

Lock the jaws in a vise-like grip around a workpiece and these pliers stay clamped in place to leave your hands free.

Squeeze the handles and the jaws automatically adjust to fit a workpiece and lock in place.

Clamp down on nonreinforced hose and tube to squeeze it shut, eliminating the need to drain the hose when working on pumps, heating and cooling systems, and fuel lines.

Attach your locking pliers to a slide hammer to pull stubborn objects.

Prevent damage to your workpieces with pliers that have nonmarring jaws. Adjust the pivot point to switch between two different jaw opening sizes.

Adjust the pivot point to switch between two different jaw opening sizes.

Insulated grips protect against accidental contact with live electrical circuits. These pliers are tested to 1,000 volts to meet IEC 60900 and ASTM F1505.

Get the best possible grip on round objects, such as oil filters, connectors, and PVC pipe. Also known as cannon plug pliers, all of these pliers have curved jaws.

Reach around closely spaced components and other obstructions.

Insulated grips protect against accidental contact with live electrical circuits. These pliers are tested to 1,000 volts to meet IEC 60900. They are shaped to reach around closely spaced components and other obstructions.

Colorful plastic grips make these assorted pliers stand out, so they’re less likely to be misplaced.

Insulated grips protect against accidental contact with live electrical circuits. These assorted pliers are tested to 1,000 volts to meet IEC 60900 and ASTM F1505.

You don't have to move the pivot point on these pliers—squeeze the handle and the jaws adjust to fit your workpiece.

More jaw positions than standard adjustable pliers enable fine adjustment and a firm grip. Push and hold the button to adjust the jaws, and then release the button to lock them in place.

Extra-long handles enable access to hard-to-reach areas. Also known as lineman’s and combination pliers, use these tools to pull, bend, and cut wire.

When there isn't clearance to use standard-grip pliers, the angled head on these tools gives you access. Also known as lineman’s and combination pliers, use them to pull, bend, and cut wire.

Deep serrations provide the firm grip necessary for pulling rebar tie wire, and the hook-shaped handle end keeps your hand from slipping off. Also known ironworkers’ pliers, these tools also bend and cut wire.

Curved, serrated jaws firmly grip hose and tube for installation and removal without damage.

Slide the pivot point of the jaws to a range of positions and squeeze the handles to grip.

More jaw positions than standard adjustable pliers enable fine adjustment and a firm grip. Push and hold the button to adjust the jaws, and then release the button to lock them in place.

A slim head and long, narrow jaws fit into tight spaces.

Avoid damaging workpieces without sacrificing gripping power and adjustability.

Secure a lanyard to the ring on the handle to prevent dropping your pliers when working at height.

Insulated grips protect against accidental contact with live electrical circuits. These pliers are tested to 1,000 volts to meet IEC 60900. Designed for looping and bending wire, they are also known as round-nose pliers.

These general purpose tweezers grip a variety of objects.

An LED lights the tips for picking up and positioning in dark areas.

Sets include an assortment of tweezers used to remove chips and other delicate components from circuit boards.

A heavy duty steel construction and long handle allow you to grip hot material in furnaces and forging and heat-treating applications.

Shaped for removing the seals around bearings, insert the tip of these tools behind the seal and pull. The curved head provides leverage to remove stuck and stubborn material.

The assorted tools in these sets are used to hold, separate, and position wire, springs, and other small parts.

Reach around obstructions and into tight spaces with picks that have long, angled tips. Use these tools to hold, separate, and position wire, springs, and other small parts.

Change tips to use a different size or style pick for holding and positioning wire, springs, and other small parts.

The handles of these assorted picks have a magnet at the end to pick up small steel objects. Use to hold and position wire, springs, and other small parts.

These assorted picks have insulated handles that protect against accidental contact with live electrical circuits. They are tested to 1,000 volts to meet IEC 60900 and ASTM F1505.

Solder won’t stick to these assorted picks, which are used for positioning circuit board components.

Replace tips when they become worn or to use a different style. The corkscrew tip twists into material to provide a firm hold while the handle provides the necessary leverage for pulling.

Sets include an assortment of handles and tips for pulling material out of tight spots. Replace tips when they become worn or to use a different style.

A different tip at each end installs and positions tiny springs and wires. Unlike conventional picks that have pointed tips, these are rounded to prevent damage to sensitive components.

Also known as packing irons, the offset handle allows you to install packing into hard-to-reach areas while the blunt tip prevents accidentally cutting or damaging the packing material.

Also known as spring plungers, these fittings are spring-loaded to accommodate items with variable heights.

These finger blanks come ready to mount to SMC or Schunk grippers, so you can make custom fingers without starting from scratch. Just machine the blank’s gripping end to create fingers that will securely grip your specific parts.

Also known as skidding tongs, these tongs have fine points that grab and hold even the hardest wood.

Pads on these clamps prevent the grip from biting into the load.

Pads on these clamps prevent the grip from biting into the load.

Clamps can take a metal plate that is stacked horizontally and tilt it up 90° to lift vertically. After lifting, clamps can place the plate back down in the original position (plate can not be flipped over).

Store tools such as brooms, cordless drills, screwdrivers, and flashlights.

Store tools such as brooms, screwdrivers, and flashlights with these holders that attach to magnetic surfaces.

Assortments include hooks, holders, and bin boxes to organize tools on a pegboard. A locking tab and mounting screw secure each piece on hardboard pegboard.

Hold instructions, safety sheets, and small bags with these clips.

Pull wire and cable while maintaining tension until the line can be permanently anchored. Use these clamps with stranded bare steel wire and cable.

Each set includes six grips for pulling one or more cables through conduit.

Stronger than aluminum cord grips, these grips are zinc plated for corrosion resistance.

Stronger than aluminum cord grips, these steel grips are zinc plated for corrosion resistance. They have a steel locknut and metal-reinforced O-ring that prevents liquid from entering the connection.

The loops tighten by the weight of your cable or by manual adjustment. These grips are often wrapped around a beam or pipe.

Hold different square drive sizes on the four clip rails stored in these trays.