Push these flexible grommets into place to protect wire, cable, and cords by turning rough-edged and uneven holes into smooth, insulated holes. Commonly used in metal panels, they also damp vibration.

These flexible grommets withstand temperatures of 450° F or greater, which is approximately twice as high as our standard grommets. Push them into place to protect wire, cable, and cords by turning rough-edged and uneven holes into smooth, insulated holes. Commonly used in metal panels, they also damp vibration.

The center hole has flaps that flex to hold and protect various sizes of wire, cable, and cords while keeping out dust and debris. Push these grommets into place. They turn rough-edged and uneven holes into smooth, insulated holes.

The center hole has flaps that flex to hold and protect various sizes of wire, cable, and cords while keeping out dust and debris. Snap these grommets into place and their wings expand against the sides of the hole to lock them in position. Use them to turn rough-edged and uneven holes into smooth holes.

Press these grommets into a hole you've already cut. They strengthen and prevent holes from fraying in tarps, covers, and curtains. They also provide a way to run rope and cable through your material.

A rolled rim provides added grip while the elongated neck and teeth on the washer, also known as a spur washer, add reinforcement and reduce rotation so you can use these grommets in thick materials such as canvas. Press the grommets into a hole you've already cut. They strengthen and prevent holes from fraying in tarps, covers, and curtains. They also provide a way to run rope and cable through your material.

The sharp neck on these grommets cuts the material as you press them into place, eliminating the need for a cutting punch. They strengthen and prevent holes from fraying in tarps, covers, and curtains. They also provide a way to run rope and cable through your material.

Create a tight seal around wire, cable, and cords with these grommets to keep out dust, debris, and moisture.

Cut the center of these grommets with a utility knife to create custom IDs. The two‐piece design makes it easy to install and seal these grommets around wire, cable, and cords that are already in place. Use them to keep out dust, debris, and moisture.

Create a sanitary seal on through-wall piping, tubing, and cables in food-, cosmetic-, and pharmaceutical-processing areas.

These grommets have two flanges that snap around holes and flex to compensate for misalignment and movement of pipe and tubing. They're often used for routing applications in panel walls.

Eliminate clutter on desktops, countertops, benchtops, and other work surfaces by organizing wire, cable, and cords.

Squeeze these flexible grommets to open the center flap—once wire, cable, and cords pass through, the flap closes tightly for dust and debris protection as well as a finished look. Use them to eliminate cord clutter on desktops, countertops, benchtops, and other work surfaces.

Made of rubber, this trim resists abrasion better than plastic trim. Often used on panels, boards, signs, and mirrors, it protects edges from impact.

A metal core adds strength and stability, making this trim more durable than standard rubber trim. Made of rubber, it resists abrasion better than plastic trim. Use it to protect the edges of panels, boards, signs, and mirrors from impact.

A metal core adds strength and stability, making this trim more durable than other high-temperature rubber trim. It withstands temperatures up to 400° F, which is generally twice as high as our standard rubber trim. Use it to protect the edges of panels, boards, and signs from impact. Made of rubber, it resists abrasion better than plastic trim.

Select this plastic trim for its chemical resistance. Often used on panels, boards, signs, and mirrors, it protects edges from impact.

With a slippery surface, this trim minimizes friction between parts and is often used on conveyor rails, chutes, and guides. Made of plastic, it's also chemical resistant.

Sample multiple sizes and styles of heavy duty plastic trim.

With a surface resistivity of 10 ⁵ ohms this trim safeguards equipment from static electricity by diverting electrostatic charges quickly. Made of plastic, it's also chemical resistant. Use it to protect the edges of of electronics equipment and circuit boards from impact.

Cushioning on the top provides added protection from impact. This nylon-coated stainless steel trim combines strength with flexibility for a snug hold. It can also protect wire, cable, and hose.

This nylon-coated stainless steel trim combines strength with flexibility to hold snugly on flat, round, and irregular-shaped edges. It can also protect wire, cable, and hose.

Black and yellow stripes create a visual alert to draw attention to equipment and obstructions. Designed to cushion during impact, this foam trim protects edges on posts, shelving, and other surfaces from damage.

A ridge on the stem provides a tighter grip than other push-in bumpers. Push the stem into a hole for quick installation. These bumpers are commonly used as feet on instruments and bench-top equipment to keep them from sliding. They're also good as spacers between sheets of material. Also known as stem and grommet bumpers.

These grips are sized to fit in tight areas.

Able to withstand temperatures up to 300° F, these grips are also corrosion- and chemical-resistant.

Because these grips resist absorbing water, they are less likely to crack or corrode than other types of plastics and metals.

A rubber bushing with an oval slot resists water and provides entry for building cable, which is also known as Romex type NM-B or type UF-B cable.

Wrap the split gland of these grips around ethernet cables with an RJ45 connector or other already installed cables for a water-resistant seal with your enclosure.

Snap these cord grips into place to secure cable in wet environments.

Tighten the screw-down clamp for superior pull-out resistance.

These grips are made of nylon, which resists most chemicals. The nylon mesh extension provides a secure hold when the cable is pulled or in motion.

Suitable for use in applications where cords are underwater—these grips are rated IP68 for protection from prolonged submersion.

Keep cords from coming loose and seal water out of enclosures in extremely cold labs and storage areas. Thanks to their plastic bushing and rubber O-ring, these grips withstand temperatures as low as -75° F.

Lighter in weight than steel and brass grips, these aluminum grips are strong enough to secure cords in demanding wet environments.

Good for wet areas where space is tight, these lightweight grips secure cords at a 90° angle while reducing the stress from bending. Made of aluminum, they’re lighter in weight than steel and brass grips yet durable.

Use these lightweight grips to secure cords entering knockouts at a 45° angle in wet, tight spaces while easing the stress from bending. Made of aluminum, they’re lighter in weight than steel and brass grips yet durable.

Made of nylon, these grips resist chemicals.

Built with snap-in tabs and a spring extension, these cord grips install into panel holes more quickly than standard grips and better prevent damage from sharp bends.

These cord grips are lightweight yet durable.

Secure and seal electrical cords entering knockouts at a 45° angle.

Stronger than aluminum cord grips, these grips are zinc plated for corrosion resistance.

Able to stand up to rust better than steel grips, these 300 series stainless steel grips secure electrical cables in corrosive environments.

Tighten the screws to secure your cable.

Also known as cable-entry seals, the cable-entry side has heat-shrinkable polyolefin with an adhesive lining.

Made of nylon, these grips resist chemicals. Install them in panels and enclosures—they have a zinc-plated steel locknut and metal-reinforced rubber O-ring that prevents liquid from entering the enclosure.

These cord grips are lightweight yet durable. They have a zinc-plated steel locknut and metal-reinforced rubber O-ring that prevents liquid from entering the connection.

These stainless steel grips offer the most protection from wet, corrosive environments of any of our metal wet-location cord grips. They are rated IP67 for protection from temporary water submersion.

Stronger than aluminum cord grips, these steel grips are zinc plated for corrosion resistance. They have a steel locknut and metal-reinforced O-ring that prevents liquid from entering the connection.

Stainless steel construction offers the most corrosion-resistance of any of our multi-diameter wet-location cord grips.

These grips meet Class III, Divisions 1 and 2 standards for use in hazardous locations.

Grips have a rubber inner grommet with multiple holes and a rubber O-ring that create a tight seal to prevent liquid from entering the connection.

The cable-entry side has heat-shrinkable polyolefin with an adhesive lining. These are also known as cable-entry seals.

Modify these cord grips to get the right fit for your cord even when you don't know the exact diameter.

FDA compliant for direct food contact, these cord grips have a multi-piece design to wrap around cables in sanitary environments without removing connectors or rewiring.

These grips have a thin, flexible seal that covers the holes until you push cords through.

Slide these grommets into conduit ends to protect wire and cable from abrasion when being pulled.

Also known as antishort bushings, these grommets slide into the ends of conduit and armored cable to protect wire and cable from sharp edges.

Protect cords routed through holes in enclosures and panels.

Press these grommets into a hole to add cushion on both sides.

Ribbed grommets are more flexible than our smooth vibration-damping grommets, so they're easier to install.

Easier to install than grommets, push these bushings through your mounting hole to dampen vibration. Use them with a vibration-damping washer to isolate vibration.

Ribbed bushings are more flexible than our smooth vibration-damping bushings, so they're easier to install.

Use these in place of normal washers to damp vibration and cushion your joint.

These female snap halves create the finished button-look of a snap. Pair them with male snap halves to create a complete snap.

Male and female snaps are included to create complete snaps.

Once installed, these fasteners provide a male snap half on both sides of your fabric. Create a complete snap by joining each male side with a female snap half for a finished look on assembled layers of fabric.

Everything you need to fasten a fabric snap to a solid surface.