These grommets snap into place and have wings that expand against the sides of the hole to lock them in position. Use them to protect wire, cable, and cords by turning rough-edged and uneven holes into smooth holes.

A slit in the side of these grommets allows you to install them around wire, cable, and cords that are already in place. They snap into the hole and their wings hold them tight. Use them to turn rough-edged and uneven holes into smooth, insulated holes.

No setting tools needed—snap the two parts together in a hole you've already cut to strengthen the hole and eliminate fraying. Use these grommets in tarps, covers, curtains, and other material.

Press these flexible grommets into holes and their tapered inner wall will expand when pipe or tubing is inserted to hold them snugly in place. They're often used for routing applications on metal, plastic, and fiberglass tanks.

Eliminate clutter on desktops, countertops, benchtops, and other work surfaces by organizing wire, cable, and cords.

Support shafts, bearings, and other moving parts that are routed through a hole. These grommets are slippery to allow parts to move freely in the hole. Install them on thin sheet-metal panels.

This trim has a metal core for added strength and stability. Made of plastic, it's also chemical resistant. Use it to protect the edges of panels, boards, signs, and mirrors from impact.

With a slippery surface, this trim minimizes friction between parts and is often used on conveyor rails, chutes, and guides. Made of plastic, it's also chemical resistant.

This trim meets FMVSS-302 for Federal Motor Vehicle Safety Standards for flammability, UL 94 HB flame requirements, and NFPA (National Fire Protection Agency) standards. Made of plastic, it's also chemical resistant. Use it to protect the edges of panels, boards, and signs from impact.

With a surface resistivity of 10 ⁵ ohms this trim safeguards equipment from static electricity by diverting electrostatic charges quickly. Made of plastic, it's also chemical resistant. Use it to protect the edges of of electronics equipment and circuit boards from impact.

Push the stem into a hole for quick installation. These bumpers are commonly used as feet on instruments and bench-top equipment to keep them from sliding. They're also good as spacers between sheets of material. Also known as stem and grommet bumpers.

Able to withstand temperatures up to 300° F, these grips are also corrosion- and chemical-resistant.

Push to install these cord grips in wet environments and high-movement applications such as robotics and handheld equipment.

Because these grips resist absorbing water, they are less likely to crack or corrode than other types of plastics and metals.

A rubber bushing with an oval slot resists water and provides entry for building cable, which is also known as Romex type NM-B or type UF-B cable.

Secure cords installed through enclosures and panels in wet environments while protecting them against sharp bends. With a flared end that keeps cords from bending without limiting too much motion, these grips extend cord life.

Made of nylon with a nylon mesh extension, these grips resist most chemicals. The mesh provides a secure hold in applications where cable is pulled or in motion.

Secure cords in washdown areas where there’s minimal space—these cord grips curve 90° to relieve stress from bending.

These grips install into enclosure holes quickly to stabilize and relieve strain on cords.

Made of nylon, these grips resist chemicals.

An insert clamps the cable in place to provide more strain relief than other snap-in cord grips for building cable.

Made of nylon, these grips resist chemicals. Install them in panels and enclosures—they have a zinc-plated steel locknut and metal-reinforced rubber O-ring that prevents liquid from entering the enclosure.

The face of these grips is flush with the cable-entry point for a seamless appearance. They have a thin, flexible seal that covers the holes until you push a cord through.

Peel away layers of rubber inserts to fit around cord grips, even when you don't know the exact diameter.

The face of these grips is flush with the cable-entry point for a seamless appearance.

Slide these grommets into conduit ends to protect wire and cable from abrasion when being pulled.

Preventing wear and cracks, these grommets shield the sections of your conduit that rub and bang against nearby components.

A spring extension prevents sharp bends and kinks in your cord, prolonging its life. These bushings, which are more rigid than grommets, shield cords from rubbing against the edges of holes in enclosures and panels, so they won’t wear down.

Ribbed grommets are more flexible than our smooth vibration-damping grommets, so they're easier to install.

Ribbed bushings are more flexible than our smooth vibration-damping bushings, so they're easier to install.

These nylon nuts are chemical resistant, nonconductive, and lightweight.

These wing-head screws have a clip-on nut that allows you to mount them near the edge of a thin panel. Use them to lock and release access panels, doors, and covers with a quarter-turn.

These rounded head nuts can be riveted into thin panels for a flush fit. They can be mounted without spaces between the panels. A quarter-turn locks and releases access panels, doors, and covers.