Hardened for increased abrasion and impact resistance, these precision-ground rods have a tight diameter tolerance and are ready for turning in your lathe.

With an oversized thickness, length, and width, these bars can be finished to your exact requirements.

These rod sets are supplied in a metal index case with fold-out panels.

Ready for turning in a lathe, these precision-ground rods have a tight diameter tolerance and are held to a strict straightness tolerance.

These bars are precision ground to a tight thickness tolerance.

Made from powdered metal, M4 tool steel has a consistent microstructure that gives it outstanding resistance to wear and abrasion. It is comparable to CPM Rex M4.

Hardened for increased abrasion and impact resistance, these rods are precision ground with a tight diameter tolerance.

These sheets and bars are precision ground to a tight thickness tolerance.

An oversized diameter allows for finishing to your exact requirements.

The thickness, length, and width are oversized for finishing to your exact requirements.

An oversized diameter allows for finishing to your exact requirements.

Also known as flat stock, these bars have an oversized thickness, length, and width for finishing to your exact requirements.

When compared to standard 304 stainless steel, this material can be machined faster with less wear on cutting tools. It's also called Prodec and Project 70+.

Each piece is precision ground to offer tighter tolerances than standard 17-4 PH stainless steel.

Also known as Project 70+, this material machines faster with less wear on cutting tools than standard 17-4 PH stainless steel.

With a diameter that’s held to a close tolerance, this material is hardened for increased wear and abrasion resistance.

Precision ground to a tight diameter tolerance, these rods are all set for turning applications in a lathe.

Also called flat stock, these precision-ground bars are held to tight thickness and width tolerances.

These sheets and bars are hardened for increased abrasion and impact resistance. Also known as chrome-moly steel, 4140 alloy steel resists fracturing from repeated stress.

Because the thickness is oversized, you can finish these bars to your exact requirements.

Also known as chrome steel, 52100 is an extremely hard and wear-resistant material. It’s used for parts such as bearings, bushings, and punches.

Stronger than low-carbon steel with equally good machinability, 1045 carbon steel is widely used for bolts, studs, and shafts.

Also known as mild steel, low-carbon steel is easy to machine, form, and weld. It's widely fabricated into parts that don’t require high strength.

Choose between sheets and bars that are precision ground on all six sides or just on the top and bottom.

Also known as flat stock, these sheets and bars are precision ground on the top and bottom.

These rods and discs are precision ground to offer tighter tolerances than standard 6061 rods and discs.

MIC6 is cast from a high-strength 7000-series aluminum, then stress relieved to maintain dimensional stability during high-speed machining.

A cobalt alloy, Cobalt 6 is tough and wear resistant.

Mount these externally threaded shafts into tapped holes rather than using a shaft support, or attach a hex nut, shaft collar, or other threaded accessory.

Lighter than solid shafts, hollow shafts reduce your total system weight and allow you to run various media such as electrical wiring, compressed air tubing, coolants, or lubricants through the center.

With 2" of each end softened, it's easier to machine a custom end for mounting. The rest of the shaft is case-hardened, which increases hardness and wear resistance on the surface of the shaft while allowing the center to remain soft for absorbing stresses caused by shifting loads.

Clip retaining rings into the grooves to separate and position collars, supports, and housings.

These shafts include a support rail for a stable setup that eliminates bending and prevents linear bearings from rotating.

Eight times straighter than standard rotary shafts, these tight-tolerance shafts minimize vibrations and reduce wear to bearings and other components. They also have diameter tolerances that are twice as tight as standard rotary shafts.

These shafts have keyways only on the ends, leaving a plain shaft in the center. Use the keyways with machine keys to transmit torque to gears, sprockets, and other keyed components. Use the middle of the shaft with bearings and other round-bore components.

Thread these shafts into a tapped hole to support idler sprockets and pulleys in tensioning applications. They have a retaining-ring groove, retaining ring, and spacers to position your component and hold it in place.

A flat surface area allows set screws to dig into the shaft for securely mounting gears, sprockets, and bearings.

Connect these internally threaded shafts directly to threaded components, or use a fastener to secure.

A shoulder near the end of the shaft provides a stop for gears, sprockets, and bearings.

With a splined profile on one end, these shafts transmit high rotational loads—good for hydraulic systems, machine tools, and other high-torque applications. Compared to keyed shafts, they last longer, handle higher torque, and do not require as tight of a fit.

Connect bare-copper ground wire to grounding rods.

Attach grounding wire to pipes.

Straps fit around pipes and grounding rods.