Clamps hold guide rails in place or join ends of a rail together.

Separate products into distinct lanes with guides and nose plows.

These brackets mount to the frame of a conveyor to hold guide clamps.

Spacers increase the distance between a bracket and the conveyor frame.

Idler wheels keep the belt moving and prevent sagging.

Find tube, pipe, fastener, wire, and drill bit sizes with one tool.

Use on external and internal fastener threads.

Trace specialty symbols for pipe fitting, electrical work, plumbing, and more.

Trace numbers and letters in three different heights.

Drill precise holes without building a fixture. Clamp the jig onto your material and lift and turn the turret to select the hole size you need.

Use these components in coordinate measuring machine (CMM) applications to raise a workpiece and reliably position it on a fixture plate with ¼"-20 holes.

Minimize friction, reduce noise, and prolong the life of your roller chain. Guides can be cut to the exact length you need.

Also known as captured guides, deep-channel guides prevent chain from slipping off track.

Also known as footman's loops, use these guides to prevent webbing from twisting, or as anchor points in tie-down applications.

Also known as sheaves, use these pulleys to assist with horizontal pulling or to guide a rope.

Also known as snatch blocks, these open so it’s easier to feed the rope through the housing—a free rope end is not needed.

Mount these pulleys to a flat surface to assist with horizontal pulling or to guide a rope.

Use the bore to mount these pulleys on a shaft. These pulleys are also known as sheaves.

Surface mount with the adhesive back to route low-voltage data and control cable where you can't get inside walls.

Insert and remove cable at any point along the length of this open-top, hook-shaped raceway.

Slide these grommets into conduit ends to protect wire and cable from abrasion when being pulled.

Also known as conduit bodies, these ports provide access to wire and cable inside PVC conduit for pulling, splicing, and maintenance. They are also used to change the direction of a run.

Connect different sizes and genders of conduit.

Also known as Type A, this conduit meets the demands of continuous motion while sealing out liquid when used with liquid-tight fittings.

One end twists into a piece of conduit for a quick connection; the other end attaches to a knockout in an outlet box or enclosure.

Visually identify different runs of wire and cable in machine and equipment wiring.

Also known as Type B, this conduit is more crush and abrasion resistant than liquid-tight flexible plastic conduit.

The spiral design makes this conduit more flexible than abrasion-resistant liquid-tight flexible plastic conduit.

Also known as antishort bushings, these grommets slide into the ends of conduit and armored cable to protect wire and cable from sharp edges.

Join pieces of conduit.

Join pieces of conduit.

Preventing wear and cracks, these grommets shield the sections of your conduit that rub and bang against nearby components.

Connect different sizes of conduit.

Curve these ramps to route cable around bends and corners in indoor areas with heavy pedestrian and equipment traffic.

Often used as an alternative to cable ties, wire duct guides and organizes short runs of electrical wiring in enclosures, control panels, and machines.

Route wire and cable around curves with this bendable wire duct.

Thread cable and hose through the entire length.

Designed for smooth, quiet travel, these carriers minimize clicking and jumping in vibration-sensitive applications such as printing and scanning.

By completely surrounding the cable and hose, these carriers protect them from dirt, chips, and debris.

Made of PVC, this sleeving resists chemicals, oil, and acids.

Made of PTFE, this sleeving has excellent resistance to chemicals and acids. A reusable alternative to tape and cable ties, it allows you to route wire and cable between the spirals.

Wrap this sleeving around cable, cords and wires to protect them and to form bundles.

Protect cables, cords, and wire and form them into bundles in your food-processing plant while lowering the risk of contaminating the food.

A hinge along the entire length makes this one-piece sleeving easy to open for installation. Interlocking ridges overlap along the opening to protect contents from dust and dirt. The corrugated construction gives it the impact and abrasion resistance of conduit, with more flexibility.

Coated with PVC, this polyester sleeving resists chemicals and solvents. It has a slit along the entire length so it easily wraps around wire, cable, and hose without disconnecting them.

Made of nylon, this sleeving is the most impact- and abrasion-resistant slit corrugated sleeving we offer. A slit along the length makes it easy to install over wire, cable, and hose without disconnecting them.

Cut, bend, and connect these wire mesh tray systems to route cable and hose in configurations such as curves, slopes, and tees.

Organize multiple lines of pipe, tubing, or hose with a single clamp. They are polyethylene for good chemical and UV resistance.