Steel Guides | McMaster-Carr

Mount these externally threaded shafts into tapped holes rather than using a shaft support, or attach a hex nut, shaft collar, or other threaded accessory.

Tapped Linear Motion Shafts

Internal threads allow you to mount these shafts onto threaded studs and fasteners, no shaft supports needed.

Hollow Linear Motion Shafts

Lighter than solid shafts, hollow shafts reduce your total system weight and allow you to run various media such as electrical wiring, compressed air tubing, coolants, or lubricants through the center.

Hollow Linear Motion Shafts with Material Certification

Keep a material certificate on hand for compliance and quality assurance needs. Certificates include a traceable lot number and material test report. These hollow shafts reduce system weight and allow you to run various media such as electrical wiring, compressed air tubing, coolants, or lubricants through the center.

Linear Motion Shafts with Retaining Ring Grooves

Clip retaining rings into the grooves to separate and position collars, supports, and housings.

Step-Down Linear Motion Shafts

A shoulder near the end of the shaft allows for easy positioning of housings, shaft supports, and collars.

Linear Motion Shafts with Machinable Ends

With 2" of each end softened, it's easier to machine a custom end for mounting. The rest of the shaft is case-hardened, which increases hardness and wear resistance on the surface of the shaft while allowing the center to remain soft for absorbing stresses caused by shifting loads.

Support-Rail Shafts

These shafts include a support rail for a stable setup that eliminates bending and prevents linear bearings from rotating.

Low-Profile Support Rails

At approximately one-third the height of standard versions, these rails provide linear shaft support in applications with low vertical clearance. They provide stability over the entire length of shaft, allow virtually unlimited travel lengths, and eliminate bending under moderate to heavy loads.

Shafts for Support Rails

Replace worn shafts in two-piece support-rail shaft systems, or mate with a support rail to create your own. The tapped mounting holes match those on our Support Rails.

Easy-Access Flange-Mounted Shaft Supports

A removable collar allows access to the shaft without unbolting the flange. For use with light to medium loads where shaft alignment is not critical, these carbon steel supports allow you to hold linear shafts perpendicular to the mounting surface. Secure the shaft by tightening the clamping screw.

Splined Shafts for Rotary and Linear Motion

Grooves on the surface of these shafts transmit rotary power while allowing bearings to move freely along the length of the shaft.

Angle Rails for V-Groove Track Rollers

Use these rails with any track rollers that have a 90° V-groove.

Measuring and Inspecting

Thread-It Screw, Bolt, and Nut Size Identifiers

Thread your fastener into holes or onto plugs for quick and accurate size identification.

Wall-Mount Thread-It Screw,
Bolt, and Nut Size Identifiers

Mount to a wall for easy access, and thread your fastener into holes or onto plugs for quick and accurate size identification.

Threads per Inch and Thread Pitch Identifiers

Determine threads per inch and thread pitch on a variety of external and internal threads.

Screw Size Identifiers

Find thread size, screw size, thread pitch, diameter, and drill bit size with one tool.

Acme Thread Identifiers

Identify Acme threads and use as a guide while grinding and cutting Acme threads to a 29° included angle.

Threads per Inch and Center Identifiers

Identify threads per inch on external threads and find the center of your workpiece to line up thread cutting tools.

Thread Identifier Sets

Set includes calipers and gauges to identify external and internal threads

Drill Bit Size Identifiers

Measure drill bit sizes with these identifiers.

Threaded Ring Gauges

Check a part’s external threads to ensure they fall within tolerance.

Threaded Ring Gauges for NPT Pipe Threads

Measure NPT pipe threads.

Threaded Plug Gauges for NPT Pipe Threads

A notch on the handle indicates when the internal NPT threads you’re checking are in tolerance.

Threaded Plug Gauges

These have a go gauge on one end and a no-go gauge on the other end.

Straightedges

Use these highly accurate straightedges as a guide to scribe and cut straight lines and to check surface straightness.

Pipe Flange Aligner Pins

Insert a pair of these nut-and bolt pins into adjacent flange holes and tighten to align flanges before connecting two pipes.

Pipe Flange Aligner Pins with Horizontal Level

Ensure horizontal alignment of pipe flanges with a level rod that runs between two alignment pins.

Stepped Pipe Flange Aligner Pins

Each step on these aligner pins matches common bolt holes on pipe flanges, so they're more precise than conical aligner pins and don’t require nuts. Press the pair of pins into mated flanges to make sure the flanges are aligned.

Drill Guides and Bushings

Press-Fit Drill Bushings

Made-to-Order Press-Fit Drill Bushings

Choose the ID, OD, and length you need.

Finish-Your-Own Press-Fit Drill Bushings

Larger OD tolerances than standard press-fit bushings allow for finishing. Bushings should be machine ground.

Metric Press-Fit Drill Bushings

Also known as jig bushings, these metric drill bushings fit inside fixture plate holes to guide drill bits, counterbores, reamers, and other cutting tools. They improve accuracy so that your drilled holes and cuts are consistent from part to part.

Made-to-Order Metric Press-Fit Drill Bushings

Choose the ID, OD, and length you need.

Press-Fit Drill Bushings with Head

The head prevents these bushings from being pushed through the jig when drilling pressure is extreme. The head sits above the jig plate or can be mounted flush by installing in a counterbored hole.

Metric Press-Fit Drill Bushings with Head

Even under extreme drilling pressure, these metric bushings won't press through your jig plate. A flanged head on the top of the bushing acts as a stop, preventing it from moving as you push down your drill bit, reamer, or other cutting bit.

Made-to-Order Press-Fit Drill Bushings with Head

Choose the ID, OD, and length you need.

Removable Drill Bushings

Replace worn bushings and quickly change IDs without needing to repeatedly use a lever press. Instead of pressing bushings in and out of your jig fixture, which can cause damage, these bushings slide in and out of sleeves.

Made-to-Order Removable Drill Bushings

Choose the ID, OD, and length you need.

Drill Bushings for Plastic

The serrations grip to prevent rotation and spin out. Press or encase into plastic tooling.

Secure-Hold Drill Bushings for Plastic

The knurls resist force and provide better holding strength than serrations. Encase in plastic tooling.

Drill Bushings for Soft Metal and Wood

The serrations at the top of the bushing grip to prevent rotation and spin out.

Removable Drill Bushings for Thin Metal

Insert these bushings into a drilled hole and twist the lock ring to secure. Reusable and easy to replace, they are held in in place by a separate locking part.

Clamp-On Drill Guides

Drill precise holes without building a fixture. Clamp the jig onto your material and lift and turn the turret to select the hole size you need.

Drill Guides

Place on your workpiece.

Tap Guides

Ensure straight, accurate threading without building a fixture.

Locators, Supports, and Stops

Screw-Mount Locating and Support Buttons

Mount through the counterbored hole with a socket head cap screw to support and position workpieces and fixtures from the bottom or side.

Press-Fit Locating and Support Buttons

Support and position workpieces and fixtures from the bottom or side. These buttons press into a drilled hole for permanent installation.

Threaded Locating and Support Buttons

Use these buttons to support and position workpieces and fixtures from the bottom or side. Their hex shape lets you screw them into a threaded hole with a wrench or socket.

Swiveling Locating and Support Buttons

The swiveling tip supports uneven and angled surfaces.

Domed-Head Locating and Support Buttons

Support rounded or irregularly shaped workpieces from the bottom or side with minimal contact.

Mating Locating Pins and Hole Liners

Maintain consistent alignment in mating parts by installing a pin in one part and a liner in the other.

Locating Pins

Install these pins in a plate or table and mate with holes in a workpiece for precise alignment.

Shoulder-Style Locating Pins

The shoulder provides a consistent height reference point and keeps the pin from being pressed through the fixture.

Threaded Locating Pins

Screw the shank into a threaded hole for quick installation and removal.

Removable Locating Pins

A slightly undersized shank makes these pins easy to install and replace. Also known as slip-fit and lock-screw locating pins, they are held in place by a separate lock screw.

Cast-In Locating Pins for Plastics

Encase these pins while molding plastic or composite parts. Once set, the knurls resist movement, letting you align the workpiece with precision on a plate or table.

Slotted Bushings

When locating a workpiece using through-hole alignment pins, use one of these bushings and one standard bushing to prevent the pins from binding in your fixture.

Through-Hole Alignment Pins

Precisely align drilled holes in two parts.

Floating Locating Pins

The head on these pins slides side-to-side in one direction. Use one of these pins and one standard round-head pin to prevent jamming when loading and unloading workpieces with inconsistent hole spacing.

Installation Tools for Spring-Loaded Guide Pins

Use these tools for easier guide pin installation.

High-Precision Index Plungers

To align two parts with more precision than standard spring plungers, these index plungers have a mating bushing that improves alignment and repeatability.

Inspection and Measuring Fixturing

Use these components in coordinate measuring machine (CMM) applications to raise a workpiece and reliably position it on a fixture plate with ¼"-20 holes.

Ball-Lock Quick-Change Fixture Clamps

Build these components into fixture plates, machine subplates, and tombstones for quick changes. The system clamps and locates at the same time for accurate positioning with repeatability of ±0.0005".

Door Track and Rollers

Roller Track for Doors

Combine track, mounting brackets, and hangers to create a system for hanging doors.

Roller Track Sets for Doors

These complete sets contain everything you need to create a system for hanging doors.

Low-Profile Roller Track for Doors

Narrow track allows you to hang doors in tight spaces.

Dust-Resistant Roller Track for Doors

Round track eliminates edges where dust and debris can accumulate.

Curved Roller Track for Doors,
Curtains, and Strip Doors

Curved track pieces allow you to create a wide variety of layouts for doors, curtains, and strip doors.

Roller Track Sets for Bypassing Doors

These sets include everything you need to hang two doors that slide past each other.

Roller Track Sets for Bypassing Cabinet Doors

For smoother operation, these sets include upper and lower roller track for hanging lightweight cabinet doors that slide past each other.

Drawer Slides

These slides fully extend for convenient access to the back of drawers.

Stacked Drawer Slides

The stacked design provides stability for deep and wide drawers.

Pass-Through Drawer Slides

Open drawers from either side of a cart or cabinet—these slides let drawers pass through for two-way access to contents.

Lock-Open/Lock-Closed Drawer Slides

A lever locks the drawer in the open as well as closed position; push the lever to release the lock.

Partial-Extension Drawer Slides

Slides only extend 3/4 of the closed length to reduce the chance that a heavy load will tip your cabinet.

Lock-Open Drawer Slides

These slides provide full extension for convenient access to the back of your drawers.

Partial-Extension Lock-Open Drawer Slides

Slides only extend 3/4 of the closed length to reduce the chance that a heavy load will tip your cabinet.

Push-to-Open Drawer Slides

When you push on the drawer, these slides force the drawer open.

Hold-Open Drawer Slides

A stop holds the drawer open; push firmly on the drawer to close.

Self-Closing Drawer Slides

These slides automatically pull the drawer closed when it approaches the closed position.

Hold-Closed Base-Mount Drawer Slides

A stop holds the drawer closed; pull firmly on the drawer to open.

Soft-Closing Heavy Duty Base-
and Under-Mount Drawer Slides

To prevent drawers from slamming shut and support them even if they’re tall and full of heavy equipment, these steel slides have soft-closing bumpers and mount to the top and bottom of drawers.

Base-Mount Drawer Slides

When you don't have enough clearance for side-mount or under-the-counter slides, mount these to the base of your drawer.

Under-the-Counter Drawer Slides

Mount these slides underneath countertops, desktops, shelves, and tables. They are often used to hold keyboard trays.

Door Guides

Use these guides to help control your door's motion and keep the bottom of the door from swinging.

Cabinet Drawer and Door Rollers

No need for drawer slides or roller track—add rollers to wood cabinet drawers and doors for smooth operation.

Webbing Guides

Also known as footman's loops, use these guides to prevent webbing from twisting, or as anchor points in tie-down applications.

Webbing Anchor Plates

Sew webbing onto these plates for a permanent anchor point or run webbing through to use them as guides.

Pulleys—For Horizontal Pulling

Pulleys for Wire Rope—For Horizontal Pulling

Also known as sheaves, use these pulleys to assist with horizontal pulling or to guide a rope.

Mounted Pulleys for Wire Rope—For Horizontal Pulling

Mount these pulleys to a flat surface to assist with horizontal pulling or to guide a rope.

Hanging Pulleys for Wire Rope—For Horizontal Pulling

Hang these pulleys from hooks, screws, and bolts to assist with horizontal pulling or to guide a rope.

Easy-Open Hanging Pulleys for
Wire Rope—For Horizontal Pulling

Also known as snatch blocks, these open so it’s easier to feed the rope through the housing—a free rope end is not needed.

Pulleys for Rope—For Horizontal Pulling

Also known as sheaves, use these pulleys to assist with horizontal pulling or to guide a rope.

Mounted Pulleys for Rope—For Horizontal Pulling

Mount these pulleys to a flat surface to assist with horizontal pulling or to guide a rope.

Hanging Pulleys for Rope—For Horizontal Pulling

Hang these pulleys from hooks, screws, and bolts to assist with horizontal pulling or to guide a rope.

Pulleys—For Lifting

Pulleys for Wire Rope—For Lifting

Use the bore to mount these pulleys on a shaft. These pulleys are also known as sheaves.

Mounted Pulleys for Wire Rope—For Lifting

Mount these pulleys to a flat surface.

Hanging Pulleys for Wire Rope—For Lifting

Hang these pulleys from hooks, screws, and bolts.

Easy-Open Hanging Pulleys for Wire Rope—For Lifting

Also known as snatch blocks, these open so it’s easier to feed the rope through the housing—a free rope end is not needed.

Easy-Open Hanging Pulleys for Rope—For Lifting

Also known as snatch blocks, these open so it’s easier to feed the rope through the housing—a free rope end is not needed.

Hanging Pulleys for Rope—For Lifting

Hang these pulleys from hooks, screws, and bolts.

Conduit, Raceway, and Wire Duct

Cable-Pulling Grip Sets

Each set includes six grips for pulling one or more cables through conduit.

Cable-Pulling Grips

Pull one or more cables through conduit.

Wire and Cable Pulling Clamps

Pull wire and cable while maintaining tension until the line can be permanently anchored. Use these clamps with stranded bare steel wire and cable.

Connectors for Choose-a-Color
Thin-Wall (EMT) Steel Conduit

Join pieces of conduit.

Adapters for Choose-a-Color
Thin-Wall (EMT) Steel Conduit

Attach conduit to a knockout in an outlet box or enclosure.

Thin-Wall (EMT) Steel Conduit

Also known as electrical metallic tubing (EMT), this conduit has thin walls that easily bend with a conduit bender and can be cut with a hacksaw.

Adapters for Thin-Wall (EMT) Steel Conduit

Attach conduit to a knockout in an outlet box or enclosure.

Connectors for Thin-Wall (EMT) Steel Conduit

Join pieces of conduit.

Choose-a-Color Thin-Wall (EMT) Steel Conduit

Visually identify different runs of wire and cable along walls and ceilings with this conduit that has a painted exterior.

Low-Profile Raceway

Route power, data, and control cable rated up to 600 volts AC/DC.

Medium-Wall (IMC) Steel Conduit

Also known as intermediate metallic conduit (IMC), this is lighter in weight than thick-wall (rigid) steel conduit, yet it has the same strength.

Thick-Wall (Rigid) Steel Conduit

This impact- and crush-resistant conduit is also known as galvanized rigid conduit (GRC).

Reducing Washers for Medium-Wall (IMC)
and Thick-Wall (Rigid) Steel Conduit

Reduce the knockout size in an outlet box or enclosure so you can attach a different size of conduit to it.

Adapters for Medium-Wall (IMC) and
Thick-Wall (Rigid) Steel Conduit

Attach conduit to a knockout in an outlet box or enclosure.

Raintight Reducing Washers for Medium-Wall
(IMC) and Thick-Wall (Rigid) Steel Conduit

Seal out moisture while reducing the knockout size in an outlet box or enclosure so you can attach a different size of conduit to it.

Bushings for Medium-Wall (IMC)
and Thick-Wall (Rigid) Steel Conduit

Join different sizes of conduit.

Connectors for Medium-Wall (IMC)
and Thick-Wall (Rigid) Steel Conduit

Join pieces of conduit.

Fittings for Liquid-Tight Flexible Metal Conduit

These fittings seal out liquids when connecting liquid-tight flexible metal conduit to a knockout in an outlet box or enclosure.

Locknuts for Metal Conduit Fittings

Secure threaded metal conduit fittings to a knockout in an outlet box or enclosure.

Adapters for Flexible Metal Conduit

Attach conduit to a knockout in an outlet box or enclosure.

Oil-Resistant Liquid-Tight Flexible Metal Conduit

In addition to resisting oil, this conduit resists lubricants and grease.

Flexible Metal Conduit

Also known as FMC, this conduit offers the crush resistance of metal combined with flexibility to handle bends in tight spaces.

Food Industry Liquid-Tight Flexible Metal Conduit

Run conduit in food areas—the cover can be cleaned and sterilized without weakening or splitting. This conduit meets NSF/ANSI standard 169 for special-purpose food equipment.

Raceway

This raceway system is also known as wireway and wire trough.

Dust-Tight Raceway

Gaskets on the covers and at connection points protect against dust as well as seeping oil and coolant.

Fittings for Continuous-Flex Liquid-Tight Plastic Conduit

These fittings seal out liquid when used with continuous-flex liquid-tight plastic conduit.

Harsh Environment Liquid-Tight Flexible Metal Conduit

The toughest liquid-tight flexible metal conduit we offer, this resists oil, chemicals, and extreme temperature fluctuations.

Conduit Adapters

Transition between types of conduit.

Extreme-Temperature Liquid-Tight
Flexible Metal Conduit

Even in temperatures as low as -50° F and as high as 220° F, this conduit stays flexible.

Liquid-Tight Flexible Metal Conduit

When used with liquid-tight fittings, this conduit seals out liquid. The steel core provides crush resistance, and the cover is UV light resistant.

Cable and Hose Carriers

Heavy Duty Open Cable and Hose Carriers

A more durable construction with a zinc-plated steel frame provides strength for a longer service life than other open cable and hose carriers.

Accessories for Any-Which-Way
Cable and Hose Carriers

Use these accessories to mount carriers to your machinery without creating an obstruction.

Corrugated Sleeving

The corrugated construction gives this sleeving impact and abrasion resistance similar to conduit, but with more flexibility.

Cable and Hose Trays

Steel Formable Cable and Hose Trays

Cut, bend, and connect these wire mesh tray systems to route cable and hose in configurations such as curves, slopes, and tees.

Zinc-Plated Steel Formable Cable and Hose Trays

The zinc plating on these tray systems offers good corrosion resistance.

Cable and Hose Trays

Create a system to route cable and hose by connecting components such as straight trays and tees.

Quick-Release Pins

Ring-Grip Quick-Release Pins

The smooth ring handle on these pins won't catch on parts. A spring-loaded, nonlocking retaining ball pops out when the pin is pushed through a hole, and retracts when the pin is pulled out.

Loop-Grip Quick-Release Pins

A bright-orange plastic-coated handle makes these pins easy to see and easy to grip. Pins have a spring-loaded ball that pops out when the pin is pushed into a hole, and retracts when the pin is pulled out.

Ball-Grip Quick-Release Pins

A smooth ball handle is easy to grip and won't catch on other parts. A spring-loaded, nonlocking retaining ball pops out when the pin is pushed through a hole, and retracts when the pin is pulled out.

Flat-Head Quick-Release Pins

These pins have a low-profile head, so they won't get knocked out of place. A spring-loaded, nonlocking retaining ball pops out when the pin is pushed through a hole, and retracts when the pin is pulled out.

T-Handle Quick-Release Pins

A T-handle makes these pins easy to grip. A spring-loaded, nonlocking retaining ball pops out when the pin is pushed through a hole, and retracts when the pin is pulled out.

Ring-Grip Shoulder-Style Quick-Release Pins

The smooth ring handle on these pins won't catch on parts. The shoulder keeps a portion of the pin outside the hole and makes them easy to grab.

T-Handle Shoulder-Style Quick-Release Pins

A T-handle makes these pins easy to grip. The shoulder keeps a portion of the pin outside the hole and makes them easy to grab.

Adjustable-Length Locking Quick-Release Pins

These pins adjust to take up play in a system or hold parts in holes of varying thicknesses. Spin the handle up or down, then tighten the locknut to change the length by up to ½”. Pins lock in place until you push the button to release the spring-loaded retaining balls.

Keyed Double-Locking Quick-Release Pins

Use the key to unlock these pins, then press the button to release the spring-loaded retaining balls. Two-step locking prevents accidental removal.

Quick-Release Pins for Access Panels

Attach these pins to a machine cover or access panel, then clip them in to receptacles installed in the enclosure for quick access. Pins lock in place until you release them.

Dowel Pins

Use these metal dowel pins as pivots, hinges, shafts, jigs, and fixtures to locate or hold parts.

Dowel Pin Stock

Cut this 12" stock to the length you need.

Oversized Dowel Pins

Oversized to fit worn and enlarged holes, these pins work well as repair and replacement parts.

Undersized Dowel Pins

Slip these pins in and out during maintenance or prototyping—they’re undersized to make alignment easier.

Half-Knurled Dowel Pins

Use these as pivot or hinge pins. The knurled half locks pins in position, while the smooth half acts as a pivot.

Knurled Dowel Pins

The full length of these pins is knurled for a tight grip that won't spin.

Two-Way Barbed Dowel Pins

Use these pins to fasten components made of soft materials such as plastic or aluminum. Opposing barbs bite into each piece, pulling them together for a tight, secure fit.

Pins for Shear Hubs

For use with Browning shear hubs, these pins are designed to fail at specific loads to protect heavy duty machinery from torque overload.

Round Head Barbed Dowel Pins

Barbs bite into plastics and soft metals such as aluminum for a strong hold, and a round head gives a finished appearance.

Spiral-Vent Pull-Out Dowel Pins

A spiral groove cut into these pins relieves trapped air but stays in 360° contact with the hole for a secure fit that's easy to insert in and remove from blind holes. To remove, thread a screw or tool into the tapped hole, then pull the pin out.

Conveying

Sensor and Reflector Brackets for Conveyors

Track for Overhead Enclosed-Track Conveyors

Brackets for Overhead Enclosed-Track Conveyors

Carriers for OverheadEnclosed-Track Powered Conveyors

Trolley Chain for OverheadEnclosed-Track Powered Conveyors

Cable Rollers

Linear Motion Shafts

Linear Motion Shafts

Threaded Linear Motion Shafts

Tapped Linear Motion Shafts

Hollow Linear Motion Shafts

Hollow Linear Motion Shafts with Material Certification

Linear Motion Shafts with Retaining Ring Grooves

Step-Down Linear Motion Shafts

Linear Motion Shafts with Machinable Ends

Support-Rail Shafts

Low-Profile Support Rails

Shafts for Support Rails

Easy-Access Flange-Mounted Shaft Supports

Splined Shafts for Rotary and Linear Motion

Splined Shafts for Rotary and Linear Motion

Angle Rails for V-Groove Track Rollers

Angle Rails for V-Groove Track Rollers

Measuring and Inspecting

Thread-It Screw, Bolt, and Nut Size Identifiers

Wall-Mount Thread-It Screw,Bolt, and Nut Size Identifiers

Threads per Inch and Thread Pitch Identifiers

Screw Size Identifiers

Acme Thread Identifiers

Threads per Inch and Center Identifiers

Thread Identifier Sets

Drill Bit Size Identifiers

Threaded Ring Gauges

Threaded Ring Gauges for NPT Pipe Threads

Threaded Plug Gauges for NPT Pipe Threads

Threaded Plug Gauges

Straightedges

Pipe Flange Aligner Pins

Pipe Flange Aligner Pins with Horizontal Level

Stepped Pipe Flange Aligner Pins

Drill Guides and Bushings

Press-Fit Drill Bushings

Made-to-Order Press-Fit Drill Bushings

Finish-Your-Own Press-Fit Drill Bushings

Metric Press-Fit Drill Bushings

Made-to-Order Metric Press-Fit Drill Bushings

Press-Fit Drill Bushings with Head

Metric Press-Fit Drill Bushings with Head

Made-to-Order Press-Fit Drill Bushings with Head

Removable Drill Bushings

Made-to-Order Removable Drill Bushings

Drill Bushings for Plastic

Secure-Hold Drill Bushings for Plastic

Drill Bushings for Soft Metal and Wood

Removable Drill Bushings for Thin Metal

Clamp-On Drill Guides

Drill Guides

Tap Guides

Locators, Supports, and Stops

Screw-Mount Locating and Support Buttons

Press-Fit Locating and Support Buttons

Threaded Locating and Support Buttons

Swiveling Locating and Support Buttons

Domed-Head Locating and Support Buttons

Mating Locating Pins and Hole Liners

Locating Pins

Shoulder-Style Locating Pins

Threaded Locating Pins

Removable Locating Pins

Cast-In Locating Pins for Plastics

Slotted Bushings

Through-Hole Alignment Pins

Floating Locating Pins

Installation Tools for Spring-Loaded Guide Pins

High-Precision Index Plungers

Inspection and Measuring Fixturing

Inspection and Measuring Fixturing

Ball-Lock Quick-Change Fixture Clamps

Ball-Lock Quick-Change Fixture Clamps

Carriers for Overhead
Enclosed-Track Powered Conveyors

Trolley Chain for Overhead
Enclosed-Track Powered Conveyors

Wall-Mount Thread-It Screw,
Bolt, and Nut Size Identifiers

Curved Roller Track for Doors,
Curtains, and Strip Doors

Soft-Closing Heavy Duty Base-
and Under-Mount Drawer Slides

Easy-Open Hanging Pulleys for
Wire Rope—For Horizontal Pulling

Connectors for Choose-a-Color
Thin-Wall (EMT) Steel Conduit

Adapters for Choose-a-Color
Thin-Wall (EMT) Steel Conduit

Reducing Washers for Medium-Wall (IMC)
and Thick-Wall (Rigid) Steel Conduit

Adapters for Medium-Wall (IMC) and
Thick-Wall (Rigid) Steel Conduit

Raintight Reducing Washers for Medium-Wall
(IMC) and Thick-Wall (Rigid) Steel Conduit

Bushings for Medium-Wall (IMC)
and Thick-Wall (Rigid) Steel Conduit

Connectors for Medium-Wall (IMC)
and Thick-Wall (Rigid) Steel Conduit