Thin wire jaws grasp small or oddly shaped objects.

An LED lights the wire jaws and the shaft bends to reach objects in awkward spaces.

Protect against accidental contact with live electrical circuits. These insulated retrievers are tested to 1,000 volts to meet IEC 60900 and ASTM F1505. The shaft bends and stays in position to reach objects in awkward spaces.

LEDs light the magnetized tip and the shaft bends and stays in position to reach objects in awkward spaces.

Push the plunger to engage the magnet; release to disengage. These retrievers bend into position and stay in place.

LEDs light the magnetized tip for picking up screws, nuts, and other small steel objects in dark areas.

An extra-long shaft enables access to material in hard-to-reach areas. These retrievers can pick up heavier objects than our other magnetic retrievers.

An extra-long shaft and pivoting head lets you access hard-to-reach material from almost any angle.

Also known as rescue hooks, these retrievers are often used to pull an injured worker away from electrical hazards without risking the safety of other workers. They have a fiberglass handle and insulated hook to protect against accidental contact with live electrical circuits. The handle is tested to meet the requirements of ASTM F711.

Magnetized on all sides, these wand-like tools remove steel chips from machinery, the floor, and your clothing. Pull the plunger to demagnetize and drop the chips into your collection bin.

The pointed tip with curved hook is good for holding and pulling cylindrical material.

The handle has a magnet at the end to pick up small steel objects. Use these picks to hold and position wire, springs, and other small parts.

A different tip at each end allows you to install, extract, and position parts with one tool.

Reach around obstructions and into tight spaces with picks that have long, angled tips. Use these tools to hold, separate, and position wire, springs, and other small parts.

Sets include a handle and an assortment of tips for holding and positioning wire, springs, and other small parts.

An insulated handle protects against accidental contact with live electrical circuits. These picks are tested to 1,000 volts to meet IEC 60900 and ASTM F1505.

Made of beryllium copper that is FM approved, these picks satisfy OSHA requirements that specify nonsparking tools for locations where flammable vapors and combustible residues are present.

Solder won’t stick to these assorted picks, which are used for positioning circuit board components.

The assorted needle-sharp picks in these sets are similar to dental instruments and suitable for work around delicate circuits and components.

Hold small parts without the need to apply pressure. Squeeze these tweezers to open the tips and release to close them.

Extra-long tips provide access to material in hard-to-reach areas.

Each style of tweezer is a different color for easy identification.

These general purpose tweezers grip a variety of objects.

Made of brass, these tweezers inhibit sparking.

A PTFE coating on the tips prevents material from sticking to these tweezers.

Choose plastic tweezers for a soft, nonmarring grip. These tools are corrosion resistant and nonmagnetic.

Sets include an assortment of tweezers used to remove chips and other delicate components from circuit boards.

These assorted tweezers have tips that can be replaced when they become worn. Tips are carbon fiber, which insulates against heat and won’t nick or scratch components.

Hold small components such as wire, capacitors, and screws in the cylindrical tips.

Cap the tips of your tweezers to protect them from damage. These flexible silicone covers fit most styles of tweezers.

Extend the life of these tweezers by replacing the tips when they become worn. Tips are carbon fiber, which insulates against heat and won’t nick or scratch components.

Designed for placing chips and electronic components on circuit boards, these tweezers have rectangular-shaped tips that are angled to reach over and around obstructions. They are also known as SMD (surface-mount device) tweezers.

These premium tweezers are Swiss made to tight tolerances for the perfect tip alignment required for work under magnification.

Keep hands away from machinery—use these lightweight tools to pick up and hold parts. The pliers-style handles provide more comfort and control than standard tongs.

Extra-slim jaws taper to a narrow point that can reach into tight spots.

Use these general purpose tongs for gripping and positioning.

Get the best possible grip on round objects, such as oil filters, connectors, and PVC pipe. Also known as cannon plug pliers, all of these pliers have curved jaws.

Smooth, consistent movement ensures precision. These tools have a slip-resistant ultra grip that’s shaped to fit comfortably in your hand and reduce strain in repetitive tasks. They are also known as miniature and electronics pliers and shaped to reach around closely spaced components and other obstructions.

Squeeze the handles to open the jaws; release to snap them closed. Once closed, they stay clamped in place to leave your hands free. These pliers reach around closely spaced components and other obstructions.

Choose a stainless steel tool for environments where moisture and other contaminants are present. These pliers resist corrosion that can hinder joint movement, but the jaws will wear more quickly than a steel tool. They are shaped to reach around closely spaced components and other obstructions

The jaws are made of brass, which won't damage steel workpieces. These pliers are shaped to reach around closely spaced components and other obstructions.

Made of stainless steel, these pliers are good for environments where moisture and other contaminants are present. They resist corrosion that can hinder joint movement, but the jaws will wear more quickly than a steel tool.

Made entirely of plastic, these pliers eliminate the potential for an arc flash or short circuit that can occur when using conventional insulated tools with metal components. They are tested to 1,000 volts to meet IEC 60900 and ASTM F1505.

Additional features, such as wire terminal crimpers and wire stripping holes, enable you to perform a variety of electrical wiring and installation work with a single tool.

Secure a lanyard to the ring on the handle to prevent dropping your pliers when working at height.

Insulated grips protect against accidental contact with live electrical circuits. These pliers are tested to 1,000 volts to meet IEC 60900 and ASTM F1505.

Prevent damage to your workpiece.

Two curved openings on the jaws grip multiple sizes of round stock, tubing, and pipe.

With thinner tips than standard long-nose pliers, these stainless steel tools fit into tight spaces and are good for environments where moisture and other contaminants are present. They resist corrosion that can hinder joint movement, but the jaws will wear more quickly than a steel tool.

Extra-wide tips give you a better grip on your work, and smooth, consistent movement ensures precision. These tools have a slip-resistant ultra grip that’s shaped to fit comfortably in your hand and reduce strain in repetitive tasks. They are also known as miniature and electronics pliers.

Choose these stainless steel pliers for environments where moisture and other contaminants are present. They resist corrosion that can hinder joint movement, but the jaws will wear more quickly than a steel tool.

Colorful plastic grips make these assorted pliers stand out, so they’re less likely to be misplaced.

Choose these tools when you need the gripping power of a pipe wrench with the adjustability of pliers. Slide the pivot point of the jaws to a range of positions.

Smooth, consistent movement ensures precision. These assorted pliers have slip-resistant ultra grips that are shaped to fit comfortably in your hand and reduce strain in repetitive tasks. They are also known as miniature and electronics pliers.

The smallest round-nose pliers we offer allow you to bend and loop wire in the smallest spaces, including under a microscope.

Choose these stainless steel pliers for environments where moisture and other contaminants are present. They resist corrosion that can hinder joint movement, but the jaws will wear more quickly than a steel tool. Also known as round-nose pliers, use them for looping and bending wire.

Insulated grips protect against accidental contact with live electrical circuits. These pliers are tested to 1,000 volts to meet IEC 60900. Designed for looping and bending wire, they are also known as round-nose pliers.

Insulated grips protect against accidental contact with live electrical circuits. These pliers are tested to 1,000 volts to meet IEC 60900 and ASTM F1505. Use them to pull, bend, and cut wire.

Deep serrations provide the firm grip necessary for pulling rebar tie wire, and the hook-shaped handle end keeps your hand from slipping off. Also known ironworkers’ pliers, these tools also bend and cut wire.

Choose a stainless steel tool for environments where moisture and other contaminants are present. These pliers resist corrosion that can hinder joint movement, but the jaws will wear more quickly than a steel tool. Use them to pull, bend, and cut wire.

When there isn't clearance to use standard-grip pliers, the angled head on these tools gives you access. Also known as lineman’s and combination pliers, use them to pull, bend, and cut wire.

Also known as lineman’s and combination pliers, use these tools to pull, bend, and cut wire.

The bottom jaw is shorter than the top for a firm grip on the flats of bolt heads and nuts that have rounded corners.

Secure a lanyard to the ring on the handle to prevent dropping your pliers when working at height.

These stainless steel pliers are good for environments where moisture and other contaminants are present. They resist corrosion that can hinder joint movement, but the jaws will wear more quickly than a steel tool.

Insulated grips protect against accidental contact with live electrical circuits. These pliers are tested to 1,000 volts to meet IEC 60900 and ASTM F1505.

Move the curved jaws to 15 positions for fine adjustment. These pliers have a bottom jaw that is shorter than the top for a firm grip on the flats of bolt heads and nuts that have rounded corners.

Avoid damaging workpieces without sacrificing gripping power and adjustability.

The narrow jaws fit into tight spaces, and the slip joint allows you to switch between two different jaw opening sizes.

Made of aluminum-bronze that is FM approved, these pliers satisfy OSHA requirements that specify nonsparking tools for locations where flammable vapors and combustible residues are present.

Removable and reusable, these rubber covers fit most slip-joint pliers and resist most oils and chemicals.

Prevent damage to your workpieces with pliers that have nonmarring jaws. Adjust the pivot point to switch between two different jaw opening sizes.

Slide steel plates and blocks off a stack.