A rubber seal protects these switches from splashing water.

Prevent accidental actuation—these toggle switches must be pulled up before they can switch a circuit.

The built-in contact block in these switches extends behind the panel half the depth of most other 22 mm switches, saving valuable space.

Because these switches mount flush against a panel, they're easy to clean and hard to damage.

Install in 14 mm dia. cutouts.

Use these switches where ignitable gas and dust may be present. Their contact blocks are UL listed for Class I, Division 2, Groups B, C, and D hazardous locations.

Immediately cut power with a single push.

Because these switches mount flush against a panel, they're easy to clean and hard to damage.

Rated NEMA 4X and 13, all switches resist corrosion and can withstand washdowns and oil/coolant spraying.

With a stainless steel enclosure, these switches are more durable than aluminum and plastic. They're rated NEMA 4X for protection from corrosion and washdowns.

These aluminum switches are rated NEMA 4, NEMA 13, and IP66 for protection from washdowns and oil/coolant spraying.

Mount these switches in an outlet box. Also known as palm-button switches, they have a large button that makes them easy to use even while wearing gloves.

These switches withstand temporary submersion.

Operate equipment from up to 330 feet away—these switches include a transmitter and a receiver that connects to equipment.

Rated IP67, these switches are protected from temporary submersion.

Rated NEMA 3S, 4X and 13, these switches are protected from corrosion, washdowns, and oil/coolant spraying.

Switches are rated NEMA 4, 13, and IP66.

These plastic switches are rated NEMA 4X, 13, and IP65 for protection from corrosion, washdowns, and oil/coolant spraying. Install them in 30 mm dia. cutouts.

Rated NEMA 4, 13, and IP66, these metal switches are protected from washdowns and oil/coolant spraying. Install them in 30 mm dia. cutouts.

Choose an actuator and contact block to make your own 16 mm switch.

Rated NEMA 6P, 13, and IP68, these switches protect against corrosion, washdowns, and temporary submersion.

Press these switches with your foot for convenient, hands-free operation.

Choose an actuator and contact block to make your own 30 mm switch.

Choose an actuator and contact block to make your own 22 mm plastic switch.

Immediately cut power by pulling the cable.

Use fingerprints to confirm the identity of personnel before granting access to secure areas or equipment.

Thicker than standard safety switch mats, these withstand repeated impact from heavy and sharp objects.

Rated NEMA 4, these switches are protected from washdowns.

Prevent personnel from getting too close to dangerous equipment when equipment is on—these mats turn equipment off when someone steps on them or when a fault is detected.

These 16 mm switches require a key to turn circuits on or off, limiting access to sensitive equipment.

Rated IP69K, these switches can withstand high-pressure, high-temperature washdowns and temporary submersion.

Set these switches to delay activation by up to five seconds after detecting an object.

Scanning 275° side-to-side for people and objects, these switches (known as safety laser scanners) cover large areas and send signals to machinery to prevent accidents.

Detect the presence or absence of an object moving at high speeds with a light beam. These switches have a longer sensing distance than proximity and ultrasonic switches.

Safely detect the presence or absence of an object moving at high speeds with a light beam. These switches produce a low-current, low-voltage NAMUR signal, so they won’t create sparks or ignite. ATEX and IECEx certified, they protect against explosion in environments containing flammable gases and combustible dust.

Set these switches to delay activation by up to fifteen seconds after detecting an object.

Easily mount these flat switches to a base or rail.

These inductive proximity switches sense metallic objects each time they pass through the slot, even when they’re obscured by water, oil, dirt, or a surface finish. Use them to measure the speed of rotating equipment and to count or detect moving objects, such as sheet metal being fed into a stamping process.

Eliminate the need to calculate the sensing distance when using different metals—these switches sense all metal at the same distance. Also known as K=1 sensors.

The flexible cable on these switches withstands applications that require frequent motion, such as robotics.

Turn the face on these switches to sense metallic objects from the front, sides, top, or bottom.

For use in volatile areas, these intrinsically safe switches detect objects when they pass through the slot. They use a NAMUR signal to operate at a low current and voltage, so they won’t ignite or create sparks. ATEX and IECEx certified, they protect against explosion.

Rotate the face on these switches five different directions for easy installation and positioning—they work with both AC and DC inputs.

Most often found in older devices, these switches require AC input voltage.

Rated NEMA 4X, 6P, IP68 and IP69K, these switches resist corrosion and high-pressure, high-temperature washdowns, and can withstand temporary submersion.

Often used with programmable logic controllers (PLCs), these switches use DC input voltage and produce PNP or NPN signal output.

Support flow and temperature control in your system with these intrinsically safe switches, which sense when a valve is open or closed in volatile areas. They are ATEX and IECEx certified to protect against explosion.

These switches actuate when a magnet comes within sensing distance, and reset when the magnet moves away.

With a rubber-encased housing and stainless steel bracket, these switches resist vibration and corrosion. They're rated IP68 for protection from dust and temporary submersion.

Keep out dirt and moisture—the sealed housing on these switches is watertight and meets MIL-PRF-8805.

Enclosures protect these snap-acting switches from the environment.

Prevent equipment from automatically restarting—these switches must be manually reset each time they're actuated.

Secure these switches into panels using mounting nuts.

Rated NEMA 6P, 13, and IP67, these switches are protected from corrosion, oil/coolant spraying, washdowns, and temporary submersion.

Rated IP67, these switches are protected from temporary submersion. When an object in motion comes into contact with the actuator, it sends a signal to open or close a circuit.

Use these switches where ignitable gas and dust may be present. They meet NEC Class I, Division 1, Groups B, C, and D; and Class II, Division 1, Groups E, F, and G for hazardous locations.

Delay access to hazardous areas until conditions are safe; use these switches with machines that take time to stop after they are turned off. They mount to a door frame.

Minimize false triggers—these switches require 10 lbs. of actuation force in order to shut off machinery immediately.

Rated IP69K, these switches are protected from high-pressure and high-temperature washdowns.

Install these switches in a panel cutout.

These switches are housed in a protective enclosure so they can be mounted wherever needed.

The NEMA 4X rated enclosure protects these starters from corrosion and washdowns.

Assemble your own motor starter by combining a switch and a thermal overload element.

Link industrial equipment with multiple computers to expand your data network.

Get NEMA 4 and IP66 protection from dirt and water. If vibration or shock exceeds a set activation point, the contacts actuate to either shut down your machine or activate an alarm.