Form this reusable putty around metal pipes and tubing or spread on a flat metal surface to stop heat from traveling to adjoining surfaces when soldering, welding, and brazing.

Thinner than most rigid insulation for furnaces and other high-heat applications, these millboard sheets are also used for gasket fabrication.

Made of high-strength calcium silicate, these durable sheets withstand high temperatures and are often used in power-generating applications.

Often used in high-humidity applications for its low moisture absorption, this flexible paper insulation is made of inorganic materials. It’s typically used in appliances and electrical devices.

Wet these rigid sheets and they become formable. They can be molded multiple times until exposed to heat, which causes them to become rigid again.

Typically used in ovens and furnaces, these are the most efficient of our rigid high-temperature insulation sheets. Please note that they require special care when installing since the crumbly material is difficult to work with and will crack easily. Sheets lose strength over time and are intended to be installed behind another facing or insulation material.

Commonly used in furnaces and engine compartments, these flexible silica fiber sheets resist corrosive acids.

The fiberglass facing on these flexible silicone foam sheets protects against highly abrasive conditions and resists tearing.

Even when subjected to heavy compression, these rigid polyimide sheets won't crack.

Stronger than standard firebricks but with lower insulation capabilities, these withstand heavy abrasion on the floors and sides of furnaces. Also known as hard firebricks.

Often used in furnaces, these firebricks have been machined for a snug fit to minimize heat loss.

Soft and easy to install, this insulation restricts absorption of water, air, and gas. It is often used on cold and hot water lines and refrigeration lines.

Lightweight and super thin, these fiber-reinforced silica aerogel sheets and strips flex into tight spaces other insulation can't. Use on process piping and in power-generating applications.

Less flexible than rubber foam, this insulation restricts absorption of water, air, and gas. It is typically used in plumbing applications

This common insulation material is typically used on hot and cold water lines and in process piping.

These rigid, lightweight melamine foam tubes are wrapped in an ISO Class 5 and Fed. Spec. Class 100 clean room jacket that is suitable for sanitary and washdown applications. They’re typically used on cold and hot water piping and with refrigeration systems.

Very rigid with a 0% water absorption rate, this insulation is unaffected by corrosive environments, organic solvents, and most acids. It is typically used in chemical-processing systems and underground lines.

These kits insulate one P-trap and two stop valves to reduce the risk of burns from accidental contact with hot pipes under your sink. The molded, flexible pipe covers are ADA compliant when properly installed.

This very rigid insulation offers the lowest heat-flow rate of our pipe insulation and restricts absorption of water, air, and gas. It is typically used in process piping and chiller plants and performs best in applications below 50° F.

Protect insulation from light impact and moisture with this durable PVC jacketing.

Wrap pipes, tubing, and fittings to prevent condensation from forming. These strips are for use on copper, iron, and steel.

Prevent condensation from forming on refrigeration and air conditioning lines and cold‐water piping.

Wrap rectangular and round ductwork with this flexible insulation.

Also known as fire wrap, these flame-resistant sheets meet ASTM E84 0/0 for flame and smoke and create a fire barrier around rectangular and round ductwork. They are often used to wrap kitchen grease exhaust ducts and air ducts.

Also known as batts, these fiberglass sheets and strips are used to insulate walls, ceilings, and floors.

Fill cracks with this single-use can of expanding foam insulation. It hardens enough to be cut in one hour.

Expanding quickly to fill large voids, this foam insulation begins to harden in 4 minutes and can be cut within 10 minutes.

Made of rugged PVC foam, these rigid sheets absorb impact and restrict the absorption of water, air, and gas. Use in applications with operating temperatures below 32° F.

These sheets are 50% more tear resistant than other fiberglass fabric sheets.

These sheets can be grounded to reduce static electricity.

Commonly used as curtains and in sealing applications.

Often used to create curtains and screens, this fabric has an aluminum foil backing that deflects radiant heat.

In addition to being oil resistant, this fabric protects against molten metal spatter when used vertically. Use as a heat shield or a welding curtain.

Resistant to sparks and molten metal spatter, this fabric withstands temperatures up to 1000° F. It's often used for curtains, blankets, and gaskets.

Use these strips for high-temperature seals and heat insulation.

More flexible than standard silica fabric, wrap these sheets and strips to insulate pipes, wires, and hose. This fabric also protects against welding spatter.

Aluminum foil is laminated to a tough fiberglass cloth to form a high-strength, reflective tape that resists temperatures up to 500° F. Use it for flame-spray masking and wire harness heat shielding.

Prevent shielding gas from escaping and protect torch components from excessive heat—these insulators form a seal between nozzle and torch.

Made of neoprene rubber, this sleeving has excellent abrasion resistance. It can be quickly applied to hose or cable like tape, so it's a good option for emergency patches.

Zip this sleeving around wire, cable, or hose that are connected at both ends to quickly bundle them.

Unlike traditional sleeving that bunches wire and cable into a circle, this sleeving holds them flat, so it’s good for tight spaces such as vehicle interiors. It has a slit along the entire length so it easily wraps around wire and cable without disconnecting them.

Coated with PVC, this polyester sleeving resists chemicals and solvents. It has a slit along the entire length so it easily wraps around wire, cable, and hose without disconnecting them.

Use this shielded sleeving to protect wire and cable from signal distortion caused by nearby equipment and devices. It has a slit along the entire length so it easily wraps around wire and cable without disconnecting them.

The tightly braided construction makes this polyester sleeving abrasion resistant. It has a slit along the entire length so it easily wraps around wire, cable, and hose without disconnecting them.

The corrugated construction gives this sleeving impact and abrasion resistance similar to conduit, but with more flexibility.

This sleeving reflects heat away from contents and withstands temperatures up to 300°F. A slit along the length makes it easy to install over wire, cable, and hose without disconnecting them. The corrugated construction gives it impact and abrasion resistance similar to conduit, with more flexibility.

A hinge along the entire length makes this one-piece sleeving easy to open for installation. Interlocking ridges overlap along the opening to protect contents from dust and dirt. The corrugated construction gives it the impact and abrasion resistance of conduit, with more flexibility.

The two halves of this sleeving nest into each other, fully enclosing contents. It has interlocking ridges that overlap to keep out dust and dirt. The corrugated construction gives it the impact and abrasion resistance of conduit, with more flexibility.

This sleeving withstands temperatures over 1000°F, such as in refineries.

A blend of Aramid and fiberglass gives this sleeving excellent abrasion resistance. It can withstand temperatures up to 650° F

Made of Nomex fabric, this sleeving has excellent tear resistance and better abrasion resistance than nylon sleeving.

Made of PVC, this sleeving resists chemicals, oil, and acids.

A specially formulated silicone rubber coating allows this sleeving to stretch over items during installation; it then tightens around its contents for a secure fit.

This sleeving withstands temperatures up to 390°F and is often used to insulate connections in transformers and relays. It prevents electricity and heat from dissipating from wire and cable.

This sleeving stretches to fit over items for easy installation, and then tightens around its contents for a secure fit. Choose from multiple colors to organize wire and cable.

Reduce the likelihood of slipping in high-traffic areas. This sleeving has thick, nonslip fibers that create friction so it doesn’t slide when you step on it. It stretches to fit over items for easy installation, then tightens around its contents for a secure fit.

With excellent torsional strength, this sleeving withstands the extreme twisting found in robotics. It has impact strength similar to steel yet is lighter than most other sleeving materials. Stretch it to fit over items for easy installation; it tightens around its contents for a secure fit.

Use this braided copper sleeving to protect wire and cable from signal distortion caused by nearby equipment and devices. It stretches to fit over items for easy installation, then tightens around its contents for a secure fit.

This sleeving absorbs UV light, so it can be used in direct sunlight without getting damaged. A reusable alternative to tape and cable ties, it allows you to route wire and cable between the spirals.

Made of PTFE, this sleeving has excellent resistance to chemicals and acids. A reusable alternative to tape and cable ties, it allows you to route wire and cable between the spirals.

Blankets are for intermittent contact with flames and hot surfaces.

Provide excellent chemical resistance with these silica cloth curtains.

The aluminum on one side of these curtains reflects radiant heat.

Shield workers while allowing them to see and be seen.

Cut with scissors to create custom see-through curtains—they have grommets and are ready to hang.

Curtains are clear so workers can see and be seen.

The vinyl coating on these panels withstands oil.

Everything you need to build a four-sided curtain partition.

Lightweight and flexible enough to roll up and carry, these panels are wire reinforced so they stand on their own.

Combine straight and curved sections to build a hanging one- to four-sided curtain partition.

Also known as wave solder gloves, wear these to avoid damaging static-sensitive electronic parts. They have a nitrile coating that protects hands while soldering.

These flexible leather gloves protect your hands from intermittent direct contact with objects or surfaces heated up to 500° F. They are more abrasion resistant than other heat-protection gloves.

Often used for casting and ceramics production, these cotton gloves are the traditional choice for jobs involving intermittent moderate heat.

Made of aluminized fabric, these gloves reflect radiant heat and protect against sparks.

Used in firefighting and similar severe duty applications, these fire-retardant gloves meet OSHA, CAL-OSHA, and NFPA requirements.