Made of high-strength calcium silicate, these durable sheets withstand high temperatures and are often used in power-generating applications.

Thinner than most rigid insulation for furnaces and other high-heat applications, these millboard sheets are also used for gasket fabrication.

The perforated vinyl facing allows moisture to evaporate and resists cracking and fading. These flexible sheets are good for insulating large enclosures.

Wet these rigid sheets and they become formable. They can be molded multiple times until exposed to heat, which causes them to become rigid again.

Typically used in ovens and furnaces, these are the most efficient of our rigid high-temperature insulation sheets. Please note that they require special care when installing since the crumbly material is difficult to work with and will crack easily. Sheets lose strength over time and are intended to be installed behind another facing or insulation material.

These durable sheets resist compression and are often used in oven and power-generating applications.

Designed for fluctuating, high-temperature applications, these semi-rigid sheets are typically used in furnaces and fire protection applications. They experience very little shrinkage at high temperatures, but the brittle material can be somewhat difficult to work with.

Made of flexible composite paper, these sheets won't shrink or lose shape in the high temperatures of air furnaces and hot water tanks.

Lay, coat, and bond firebricks. Apply this mortar with a trowel.

Often used in furnaces, these firebricks have been machined for a snug fit to minimize heat loss.

Shield against extreme heat with these flexible ceramic strips. They are often used to insulate hose, cables, and process piping.

Soft and easy to install, this insulation restricts absorption of water, air, and gas. It is often used on cold and hot water lines and refrigeration lines.

Rigid and flame resistant, these insulation tubes are typically used in process piping and mechanical systems.

Lightweight and super thin, these fiber-reinforced silica aerogel sheets and strips flex into tight spaces other insulation can't. Use on process piping and in power-generating applications.

Less flexible than rubber foam, this insulation restricts absorption of water, air, and gas. It is typically used in plumbing applications

These rigid, lightweight melamine foam tubes are wrapped in an ISO Class 5 and Fed. Spec. Class 100 clean room jacket that is suitable for sanitary and washdown applications. They’re typically used on cold and hot water piping and with refrigeration systems.

Reduce the risk of burns from accidental contact with hot pipes under your sink. These molded, flexible pipe covers are ADA compliant when properly installed.

Able to withstand temperatures as low as -290° F, these super-thin, lightweight sheets are made of fiber-reinforced silica aerogel that can flex into tight spaces other insulation can't. Use in process piping and power-generating applications.

Guard insulation from heavy impact and chemical exposure. This metal jacketing is corrosion resistant and often used outdoors.

Save installation time with banding that’s ready to use. It has an easy-to-close fastener on one end.

Wrap pipes, tubing, and fittings to prevent condensation from forming. These strips are for use on copper, iron, and steel.

Protect equipment and surfaces from radiant heat. These flexible sheets have an adhesive back for installation.

Small puffs of loose-fill insulation can be packed as densely as you choose. Pour or blow it into walls and ceilings, or mix it into insulating cements as a filler.

Cover large areas with this two-part expanding foam insulation.

Fill cracks with this single-use can of expanding foam insulation. It hardens enough to be cut in one hour.

These sheets resist the absorption of water, air, and gas and are widely used in cold-storage and packaging applications.

Typically used as duct wrap, these flexible sheets consist of polyethylene bubbles covered with aluminum polyester foil that prevent 96% of heat from radiating into or away from duct. Use on rectangular and round ductwork.

Wrap rectangular and round ductwork with this flexible insulation.

Made from thicker and denser fiberglass than standard spark-resistant sleeving, this sleeving is more abrasion resistant and provides better insulation. The silicone rubber coating protects against sparks and molten metal splash.

This sleeving withstands temperatures up to 390°F and is often used to insulate connections in transformers and relays. It prevents electricity and heat from dissipating from wire and cable.

Add a layer of insulation to prevent electricity and heat from dissipating from wire and cable.

With a temperature rating of 1800°F or higher, this sleeving can withstand hotter temperatures than fiberglass and most ceramic.

Unlike fiberglass and silica, this sleeving won't irritate skin, so it's easier to handle. It has a temperature rating of 1100° F or higher.

Made of Nomex fabric, this sleeving has excellent tear resistance and better abrasion resistance than nylon sleeving.

Rated UL 2024 and NFPA 262, this sleeving is approved for use in plenum spaces such as duct work and above a drop ceiling. It self-extinguishes and emits minimal amounts of smoke and gas during combustion. Stretch to fit over items for easy installation; it tightens around its contents for a secure fit.

Protect cable, hose, and pipe in high temperature environments—this sleeving withstands temperatures over 450° F. It stretches to fit over items for easy installation, then tightens around its contents for a secure fit.

Made of aluminum with a fiberglass liner, this sleeving reflects heat away from contents and withstands temperatures up to 390°F. A slit along the entire length makes it easy to install around wire, cable, and hose without disconnecting them.

The tightly braided construction makes this polyester sleeving abrasion resistant. It has a slit along the entire length so it easily wraps around wire, cable, and hose without disconnecting them.

This sleeving reflects heat away from contents and withstands temperatures up to 900°F. The corrugated construction gives it impact and abrasion resistance similar to conduit, but with more flexibility.

Rated UL 94 V-2, this sleeving resists combustion and minimizes the spread of flames. A slit along the length makes it easy to install over wire, cable, and hose without disconnecting them. It has impact and abrasion resistance similar to conduit, with more flexibility.

With larger openings than porous fiberglass fabric, these sheets allow for more air circulation in drying applications.

These sheets can be grounded to reduce static electricity.

These sheets are 50% more tear resistant than other fiberglass fabric sheets.

Commonly used as curtains and in sealing applications.

A blend of aramid and fiberglass, this fabric resists mildew and abrasion. It is self-extinguishing and won't melt, so it's often used for insulation applications.

Resistant to sparks and molten metal spatter, this fabric withstands temperatures up to 1000° F. It's often used for curtains, blankets, and gaskets.

Even when exposed for as long as 2 minutes to temperatures up to 2600° F, these sheets won't ignite or melt.

Commonly used as curtains, covers, insulation, and splash shields, these sheets protect against welding spatter.

With an aramid honeycomb core sandwiched between carbon fiber or fiberglass for rigidity, these panels are strong, but lightweight, and won’t conduct heat. Often used as wall panels in structural and insulating applications, they’re a lightweight alternative to solid composite and aluminum honeycomb panels.

These curtains are for intermittent contact with flames and hot surfaces.

Made with Kevlar to resist abrasion, scratches, tears, and punctures.

You can see and walk through these strip curtains.

Combine straight and curved sections to build a hanging one- to four-sided curtain partition.

Hinges allow you to fold these panels into the desired configuration while the clear screens let workers see and be seen.

Fold these hinged panels into the configuration you need.

This tape reflects intense heat to protect sensitive components.

The adhesive on this conformable aluminum foil tape is electrically conductive for use on surfaces that can't be soldered. Use it to shield cables and electronic components from EMI (electromagnetic interference).

Prevent shielding gas from escaping and protect torch components from excessive heat—these insulators form a seal between nozzle and torch.

Completely block light to maintain darkness and privacy, while allowing traffic to flow freely.

Made of treated cotton, these pants provide better protection against wear and abrasion than base-layer pants.

Shorter than coats, jackets cover your hips.

Cover your waist and the top of your legs from heat and sparks when welding.

Protect the front of your legs against radiant heat, flames, and welding sparks. Made of flexible leather, these chaps resist cuts and abrasion.

Longer than jackets, coats extend past the knee.

Made of cotton, these coveralls are treated to protect against low radiant heat and minor sparks when welding.

Protect your arms and chest from heat and sparks when welding.

These knee-length coats are made of breathable cotton and are self-extinguishing. A flap in the front conceals the zipper.

Wear these fitted garments under clothing for an added layer of protection against intermittent exposure to flames and radiant heat. They meet NFPA 70E standards for protection against electrical arc flashes for personal protection equipment (PPE) category 1 or 2.

Made of a cotton blend, these pants are lightweight and offer better breathability than denim jeans.

These knee-length coats offer more coverage than jackets to protect against heat and sparks. Hot particles won't get trapped because there are no pockets. Pull tabs allow for quick removal.

These pants have no pockets, so they won’t trap hot particles when protecting against sparks. They have durable leather belt loops, as well as buttons for suspenders.

These adjustable leggings protect your shins and the top of your feet from heat, sparks, and molten metal splashes. They have pull tabs for quick removal.

3000 series aluminum stands up to outdoor use, as well as exposure to chemicals. It offers a good combination of strength, formability, and weldability. It's often used for storage tanks, heat exchangers, garage doors, and general sheet metal work.

A honeycomb core is bonded between two aluminum sheets for rigidity.

Designed for TIG welding, these gloves are thinner than MIG gloves for more flexibility and sensitivity.

Use these sleeves alone or with gloves to protect your arms from welding sparks and spatter.

Protect your hands from intermittent handling of hot objects. These gloves are rated for cut resistance to guard hands from sharp objects.

Designed for intermittent handling of hot pipes, engine parts, and castings, these gloves protect your hands from moderate heat and some abrasion.

Slip these pads over gloves for additional protection against sparks and spatter.

These pads allow you to rest your arm on a hot surface while welding.

Use these sleeves alone or with gloves to protect your arms from heat.

Used in firefighting and similar severe duty applications, these fire-retardant gloves meet OSHA, CAL-OSHA, and NFPA requirements.

Thick aramid fabric protects hands when handling hot, dry objects such as heated ceramics and glass flasks. Gloves are cleaned and bagged in environments with low levels of particulates to avoid work area contamination.

ASTM D120 rated for use when handling live electrical equipment, these gloves come tested and marked with the test date. All gloves meet NFPA 70E for protection against arc-flash hazards.