Turn the dial to control the percentage of time that these heaters cycle on, from 5% to 100%. Commonly used to thaw pipes, prevent valves from freezing, and heat beakers and flasks in labs, they're good for temporary and occasional use where rapid heating is required but precise temperature control is not.

Wrap the flexible fiber heating element around small-diameter pipes and tubes or pack it into tight spaces.

There’s no need for power-connection kits with these finished lengths of cable.

Rated for a maximum heat output of 900° F, these heaters are often used for thawing frozen pipes and rapid spot heating.

For applications requiring high heat over long periods of time, these aluminized steel heaters warm up faster and are more durable than silicone rubber heaters.

Nonstandard-size containers are no problem—use the hook-and-loop closure to adjust these heaters to fit a range of diameters.

These heaters require a separate temperature switch or controller to regulate heat output.

For more durability than other adhesive-mount heaters, a thick layer of fiberglass-reinforced silicone rubber encases the heating element.

Resistant to sparks and molten metal spatter, this fabric withstands temperatures up to 1000° F. It's often used for curtains, blankets, and gaskets.

Similar to plaster, these adhesive-impregnated sheets and strips become moldable when water is added and harden as they dry. They can be used in sealing, insulating, and covering applications.

These sheets can be grounded to reduce static electricity.

Pores allow for air circulation, so these sheets are often used in drying applications.

Often used to create curtains and screens, this fabric has an aluminum foil backing that deflects radiant heat.

In addition to being oil resistant, this fabric protects against molten metal spatter when used vertically. Use as a heat shield or a welding curtain.

More flexible than standard silica fabric, wrap these sheets and strips to insulate pipes, wires, and hose. This fabric also protects against welding spatter.

Use these strips for high-temperature seals and heat insulation.

This temperature-resistant fabric is more cut resistant than Nomex.

This sleeving withstands temperatures over 1000°F, such as in refineries.

Unlike fiberglass and silica, this sleeving won't irritate skin, so it's easier to handle. It has a temperature rating of 1100° F or higher.

Made of Nomex fabric, this sleeving has excellent tear resistance and better abrasion resistance than nylon sleeving.

A silicone rubber coating on this fiberglass sleeving protects against sparks and molten metal splash.

A specially formulated silicone rubber coating allows this sleeving to stretch over items during installation; it then tightens around its contents for a secure fit.

Protect cable, hose, and pipe in high temperature environments—this sleeving withstands temperatures over 450° F. It stretches to fit over items for easy installation, then tightens around its contents for a secure fit.

Made of aluminum with a fiberglass liner, this sleeving reflects heat away from contents and withstands temperatures up to 390°F. A slit along the entire length makes it easy to install around wire, cable, and hose without disconnecting them.

Often used to protect wire, cable, and hose in robotics and other automated applications, this highly flexible sleeving withstands continuous motion without tearing or fraying.

Made of PTFE, this sleeving has excellent resistance to chemicals and acids. A reusable alternative to tape and cable ties, it allows you to route wire and cable between the spirals.

Superior in strength and durability, these thin strips insulate as well as protect personnel from accidental contact with hot pipes. Use for exhaust, hot water, and process pipes.

Even at high temperatures, these tubes remain flexible to stretch over components without tearing. They restrict absorption of water, air, and gas and are typically used on hot and cold water lines and electrical components.

Hook-and-loop fasteners make it easy to install, remove, and reuse this flexible insulation. Use on steam, hot water, and process pipes and fittings.

This common insulation material is typically used on hot and cold water lines and in process piping.

Lightweight and super thin, these fiber-reinforced silica aerogel sheets and strips flex into tight spaces other insulation can't. Use on process piping and in power-generating applications.

These rigid, lightweight melamine foam tubes are wrapped in an ISO Class 5 and Fed. Spec. Class 100 clean room jacket that is suitable for sanitary and washdown applications. They’re typically used on cold and hot water piping and with refrigeration systems.

This very rigid insulation offers the lowest heat-flow rate of our pipe insulation and restricts absorption of water, air, and gas. It is typically used in process piping and chiller plants and performs best in applications below 50° F.