When you don't have exact alignment between the fastener and the tool, the ball end allows angled entry to turn screws in hard-to-reach areas.

A magnet or retaining ring holds the nut in place.

Because they make contact on the flat sides of fasteners rather than only on the corners, these magnetic bits significantly reduce slipping and stripping. They’re also known as lobular bits.

Assortments contain bits with multiple drive styles.

A magnet holds the nut in place.

An opening at the tip accommodates the pin in the recess of tamper-resistant hex screws. These are also known as pin-in-hex or pin-in-socket bits.

The assorted drivers in these sets have a ball end that allows angled entry to turn screws in hard-to-reach areas.

A holding mechanism at the tip of the tool ensures the screw won’t slip off.

When working in tight spaces, these short drivers fit where others can't.

A scaled-down version of standard nutdrivers, these tools are shorter, slimmer, and easy to take with you.

The shaft and handle are drilled all the way through for turning nuts on any length of threaded rod. These drivers have a magnet in the tip to hold nuts in place.

A magnet in the tip holds nuts in place.

The assorted drivers in these sets have an insulated handle and shaft that protect against shock from accidental contact with live electrical circuits. They are tested to 1,000 volts to meet ASTM and IEC standards.

Protect your stainless steel fasteners by using a stainless steel driver. If steel flakes off a standard tool and into the threads, it can lead to rust and contamination. These drivers eliminate that risk.

Sets include an assortment of keys. These simple tools turn fasteners from either end and reach into tight spots.

These assorted keys have a ball end that allows angled entry to make good contact with the screw recess when standard-tip keys can’t. Use to turn screws in hard-to-reach spots.

The extra-short leg of these keys fits in tight spaces other tools can't and the long-leg ball end allows angled entry to turn screws in hard-to-reach areas.

These assorted keys have a bright finish that's easy to see, so they’re less likely to be misplaced. They turn fasteners from either end and reach into tight spots.

When a standard-tip key can't make good contact with the recess, a ball end allows angled entry to turn screws in hard-to-reach places. These keys have a bright gold-plated finish that makes them easy to see and less likely to be misplaced.

These keys have an extra-short leg to fit into tight spaces that other tools can’t, and a ball on the long leg for angled entry to turn screws in hard-to-reach places. A bright chrome-plated finish makes them easy to see and less likely to be misplaced.

Sets include assorted keys with each size a different color for easy identification. When a standard-tip key can't make good contact with the recess, a ball end allows angled entry to turn screws in hard-to-reach places.

These assorted keys have a detent that grips inside the recess to ensure screws won’t fall off. The ball end allows angled entry to drive fasteners in hard-to-reach areas.

The zinc coating on these keys resists salt-spray exposure. They turn fasteners from either end and reach into tight spots.

Sets include an assortment of stainless steel keys with a ball end that allows angled entry to turn screws in hard-to-reach areas. Use a stainless steel L-key to protect your stainless steel screws. If steel flakes off a standard tool and into the recess, it can lead to rust and contamination. These keys eliminate that risk.

Sets include an assortment of stainless steel keys, which protect stainless steel screws. If steel flakes off a standard tool and into the recess, it can lead to rust and contamination. These keys eliminate that risk.

These assorted keys are made of beryllium copper that is FM approved. They help meet OSHA requirements that specify nonsparking tools for locations where flammable vapors and combustible residues are present. Keys turn fasteners from either end and reach into tight spots.

Sets include assorted keys with long shafts that reach into tight spots. The plastic-covered handles provide a good grip for your whole hand.

Sets include an assortment of short keys that fit in tight spaces where others can't.

These assorted keys have a ball end that allows angled entry to make good contact with the screw recess when standard-tip keys can’t.

These assorted keys have a ball end that allows angled entry to make good contact with the screw recess when standard-tip keys can’t. The textured grip provides comfort, slip resistance, and maximum torque.

These assorted keys have a textured grip that provides comfort, slip resistance, and maximum torque. They have a long shaft for reaching into tight spots to turn fasteners.

The economical choice, these sets include an assortment of keys with a simple loop handle. The long shaft reaches into tight spots and the T-handle provides a good grip for your whole hand when turning fasteners.

These sets include an assortment of keys with a ball end on the long shaft, which allows angled entry to turn screws in hard-to-reach areas. The short shaft provides additional torque.

The ball-end tip has a retaining ring that grips inside the recess to hold screws in place and allows angled entry to turn fasteners in hard-to-reach areas.

Protect your stainless steel screws by using a stainless steel key. If steel flakes off a standard tool and into the recess, it can lead to rust and contamination. These keys eliminate that risk.

An insulated handle and shaft protect against shock from accidental contact with live electrical circuits. These tools are tested to 1,000 volts to meet IEC and ASTM standards. They have a long shaft that reaches into tight spots to turn fasteners.

When a straight-end key can't make good contact with the recess, a ball end allows angled entry to turn screws in hard-to-reach places.

Insulated to protect against accidental contact with live electrical circuits, these sockets are tested to 1,000 volts to meet ASTM F1505 and IEC 60900.

The short bit on these sockets fits in spaces where height clearance is limited.

The ball end allows angled entry when you don't have exact alignment between the socket bit and fastener.

These short sockets fit spaces where height clearance is limited.

Insulated to protect against accidental contact with live electrical circuits, these sockets are tested to 1,000 volts to meet IEC 60900.

A ratchet mechanism allows you to turn fasteners without removing and repositioning the socket.

Often used with an extension, these sockets turn fasteners and fittings in obstructed areas that a regular socket can't reach. They are also known as crowfoot wrenches.

Turn nuts on bolts and threaded rod, which pass through these sockets.

Achieve the best possible grip on hex fasteners and prevent rounding.

Pivot the head to access fasteners from an angle.

The 12-point shape quickly positions on hex fasteners.

A magnet holds the fastener securely enough to drive self-tapping screws.

Extra-long bits allow access to hard-to-reach fasteners.

Extra-long bits allow access to hard-to-reach fasteners.

Keep a convenient mix of hex, Torx, Phillips, and slotted bit sockets on hand.

Suitable for occasional maintenance work, these sets are imported.

For high quality at a lower price, choose these U.S.A.-made sets.

Made in the U.S.A., these tools handle the toughest industrial applications, provide the best grip on fasteners, and have a superior finish.

Made of aluminum-bronze, these sockets satisfy OSHA requirements that specify nonsparking tools for locations where flammable vapors and combustible residues are present.

A ratchet mechanism allows you to turn fasteners without removing and repositioning the socket.

The opening shape makes more contact with fasteners for a better grip than standard open-end sockets. Also known as flare-nut or line wrench sockets, they're often used with flared tube fittings and fuel and hydraulic lines.

The hex shape grips hex fasteners and prevents rounding. These sockets are made to withstand the high torque and force of impact tools.

A spline-shaped box end turns spline, hex, and 12-point fasteners. This shape also gets a better grip on rounded fasteners that can be difficult to turn with a traditional wrench.

Open the jaws to fit around a fastener like an open-end wrench; close the jaws and the wrench acts like a ratcheting box wrench.

Open the jaws to fit around a fastener like an open-end wrench; close the jaws and the wrench acts like a ratcheting box wrench.